Searched refs:temperatures (Results 1 – 25 of 65) sorted by relevance
123
| /Linux-v4.19/Documentation/hwmon/ |
| D | smsc47m192 | 31 Voltages and temperatures are measured by an 8-bit ADC, the resolution
32 of the temperatures is 1 bit per degree C.
38 show voltages in mV and temperatures in units of 0.001 degC.
78 temp[1-3]_max - lower and upper alarm thresholds for temperatures
88 All temperatures and offsets are read and written in
|
| D | tmp103 | 18 temperatures to a resolution of 1°C. The TMP103 is specified for
24 The driver provides the common sysfs-interface for temperatures (see
|
| D | adt7462 | 18 can also measure 13 voltages or 4 temperatures, or various combinations of the
27 response to the measured temperatures without further host intervention. This
41 The ADT7462 have a 10-bit ADC and can therefore measure temperatures
|
| D | lm83 | 28 Using the adm1021 driver for a LM83 should work, but only two temperatures
59 won't have to handle more than two temperatures. Thus, ADM1021 clones
60 are sufficient, and there is no need for a four temperatures sensor
74 is given within a range of 0 to +85 degrees. Remote temperatures are
|
| D | tmp108 | 17 can be set when temperatures exceed minimum or maximum values plus or minus a
35 The driver provides the common sysfs-interface for temperatures (see
|
| D | adt7470 | 20 external temperatures. It has four (4) 16-bit counters for measuring fan speed.
27 response to the measured temperatures with further host intervention. This
43 The ADT7470 has a 8-bit ADC and is capable of measuring temperatures with 1
|
| D | k8temp | 25 will auto-detect the sensors and will display only temperatures from
37 temperature is updated once a second. Valid temperatures are from -49 to
|
| D | lm85 | 54 temperatures and five (5) voltages. It has four (4) 16-bit counters for
64 The temperatures measured are one internal diode, and two remote diodes.
74 response to the measured temperatures without further host intervention.
99 optional filter for smoothing temperatures. The ADM1027 has the same
103 measure temperatures with 0.25 degC resolution. They also provide an offset
124 The SMSC EMC6D100 & EMC6D101 monitor external voltages, temperatures, and
222 the temperatures to compensate for systemic errors in the
|
| D | adt7475 | 42 temperatures and two (2) or more voltages. It has four (4) 16-bit counters
50 response to the measured temperatures without further host intervention.
85 The ADT747x has a 10-bit ADC and can therefore measure temperatures
|
| D | thmc50 | 40 until the temperature falls below the Hysteresis value. All temperatures are in
60 The driver provides up to three temperatures:
|
| D | pc87360 | 44 (PC87366) temperatures.
103 step by step and keep an eye on temperatures.
123 measurement) one. As a consequence, these temperatures are exported as
124 voltages, and converted into temperatures in user-space.
|
| D | tmp102 | 25 The driver provides the common sysfs-interface for temperatures (see
|
| D | sch5627 | 17 capabilities. They can monitor up to 5 voltages, 4 fans and 8 temperatures.
|
| D | wm831x | 31 Temperatures are sampled by a 12 bit ADC. Chip and battery temperatures
|
| D | nct6775 | 61 temperatures. The driver reports up to 10 of the temperatures to the user.
184 points should be set to higher temperatures and higher pwm values to achieve
209 temperatures, and in some cases the reported temperature declines if the actual
|
| D | ftsteutates | 17 enhancements. It can monitor up to 4 voltages, 16 temperatures and
|
| D | adm1031 | 29 degree for the local temperature, 0.125 degree for the remote temperatures.
|
| D | w83773g | 20 therefore reports true temperatures that don't need any user-space adjustments.
|
| /Linux-v4.19/Documentation/devicetree/bindings/hwmon/ |
| D | max6697.txt | 32 Select bit 0 for local temperature, bit 1..7 for remote temperatures.
37 Select bit 0 for local temperature, bit 1..7 for remote temperatures.
45 Only supported for remote temperatures (bit 1..7).
|
| /Linux-v4.19/Documentation/devicetree/bindings/thermal/ |
| D | nvidia,tegra186-bpmp-thermal.txt | 4 interface that is used to read system temperatures, including CPU cluster
5 and GPU temperatures. This binding describes the thermal sensor that is
|
| D | da9062-thermal.txt | 7 high THERMAL_TRIP_HOT temperatures for the PMIC device.
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/adc/ |
| D | mt6577_auxadc.txt | 5 in some Mediatek SoCs which among other things measures the temperatures
7 used by thermal controller which reads the temperatures from the AUXADC
|
| /Linux-v4.19/drivers/thermal/tegra/ |
| D | Kconfig | 10 zones to manage temperatures. This option is also required for the
|
| /Linux-v4.19/drivers/net/can/peak_canfd/ |
| D | Kconfig | 13 operated with ambient temperatures in a range of -40 to +85 °C.
|
| /Linux-v4.19/drivers/gpu/drm/amd/powerplay/inc/ |
| D | power_state.h | 153 struct PP_TemperatureRange temperatures; member
|
123
