| /Linux-v4.19/Documentation/devicetree/bindings/clock/ |
| D | ti,cdce925.txt | 28 For all PLL1, PLL2, ... an optional child node can be used to specify spread
30 - spread-spectrum: SSC mode as defined in the data sheet.
31 - spread-spectrum-center: Use "centered" mode instead of "max" mode. When
46 spread-spectrum = <4>;
47 spread-spectrum-center;
|
| D | marvell,berlin.txt | 7 Clock related registers are spread among the chip control registers. Berlin
|
| /Linux-v4.19/Documentation/misc-devices/ |
| D | ics932s401 | 20 frequency. If spread spectrum mode is enabled, the driver also reports by what
21 percent the clock signal is being spread, which should be between 0 and -0.5%.
|
| /Linux-v4.19/Documentation/devicetree/bindings/ata/ |
| D | imx-sata.txt | 24 - fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA
|
| /Linux-v4.19/Documentation/devicetree/bindings/phy/ |
| D | rcar-gen3-phy-usb3.txt | 5 If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL
33 - renesas,ssc-range: Enable/disable spread spectrum clock (ssc) by using
|
| D | brcm-sata-phy.txt | 26 - brcm,enable-ssc: use spread spectrum clocking (SSC) on this port
|
| /Linux-v4.19/fs/udf/ |
| D | balloc.c | 554 uint32_t spread = 0xFFFFFFFF, nspread = 0xFFFFFFFF; in udf_table_new_block() local
585 while (spread && in udf_table_new_block()
598 if (nspread < spread) { in udf_table_new_block()
599 spread = nspread; in udf_table_new_block()
614 if (spread == 0xFFFFFFFF) { in udf_table_new_block()
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | imx6q-dms-ba16.dts | 113 fsl,no-spread-spectrum;
|
| D | imx6q-cubox-i.dts | 58 fsl,no-spread-spectrum;
|
| D | imx6q-cubox-i-emmc-som-v15.dts | 59 fsl,no-spread-spectrum;
|
| D | imx6q-cubox-i-som-v15.dts | 58 fsl,no-spread-spectrum;
|
| D | imx6q-hummingboard2-emmc-som-v15.dts | 62 fsl,no-spread-spectrum;
|
| D | imx6q-hummingboard2-som-v15.dts | 61 fsl,no-spread-spectrum;
|
| D | imx6q-hummingboard2.dts | 60 fsl,no-spread-spectrum;
|
| /Linux-v4.19/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-zx.txt | 40 the pin spread in both controllers. This type of pins are called 'AON pins'.
|
| /Linux-v4.19/Documentation/device-mapper/ |
| D | switch.txt | 21 is created it is spread across multiple members. The details of the
43 spread with an address region size on the order of 10s of MBs, which
|
| /Linux-v4.19/drivers/gpu/drm/bridge/ |
| D | tc358767.c | 185 int spread; member
392 if (tc->link.spread) in tc_srcctrl()
621 tc->link.spread = tmp[0] & BIT(0); /* 0.5% down spread */ in tc_get_display_props()
935 tmp[0] = tc->link.spread ? DP_SPREAD_AMP_0_5 : 0x00; in tc_main_link_setup()
|
| /Linux-v4.19/Documentation/devicetree/bindings/regulator/ |
| D | regulator.txt | 79 - regulator-coupled-max-spread: Max spread between voltages of coupled regulators
|
| /Linux-v4.19/kernel/irq/ |
| D | Kconfig | 118 ( Sparse irqs can also be beneficial on NUMA boxes, as they spread
|
| /Linux-v4.19/Documentation/devicetree/bindings/arm/marvell/ |
| D | marvell,berlin.txt | 59 CPU boot address. Unfortunately, the individual registers are spread among the
|
| /Linux-v4.19/Documentation/cgroup-v1/ |
| D | cpusets.txt | 22 1.6 What is memory spread ?
178 - cpuset.memory_spread_page flag: if set, spread page cache evenly on allowed nodes
179 - cpuset.memory_spread_slab flag: if set, spread slab cache evenly on allowed nodes
303 1.6 What is memory spread ?
311 the kernel will spread the file system buffers (page cache) evenly
316 then the kernel will spread some file system related slab caches,
329 When new cpusets are created, they inherit the memory spread settings
333 or slab caches to ignore the task's NUMA mempolicy and be spread
336 their containing task's memory spread settings. If memory spreading
367 to access large file system data sets that need to be spread across
|
| /Linux-v4.19/tools/perf/Documentation/ |
| D | callchain-overhead-calculation.txt | 19 spread over the children.
|
| /Linux-v4.19/kernel/sched/ |
| D | debug.c | 499 spread, rq0_min_vruntime, spread0; in print_cfs_rq() local
529 spread = max_vruntime - MIN_vruntime; in print_cfs_rq()
531 SPLIT_NS(spread)); in print_cfs_rq()
|
| /Linux-v4.19/include/uapi/linux/ |
| D | omap3isp.h | 607 __u8 spread; member
|
| /Linux-v4.19/Documentation/filesystems/ext4/ondisk/ |
| D | allocators.rst | 48 block group that it can find. This encourages directories to spread out
|
