Searched refs:resistance (Results 1 – 25 of 39) sorted by relevance
12
| /Linux-v4.19/Documentation/devicetree/bindings/hwmon/ |
| D | max6697.txt | 40 - resistance-cancellation
41 Boolean for all chips other than MAX6581. Set to enable resistance
43 For MAX6581, resistance cancellation enabled for all channels if
46 If not specified, resistance cancellation will be disabled for all
61 resistance-cancellation;
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/light/ |
| D | cm3605.txt | 25 - capella,aset-resistance-ohms: the sensitivity calibration resistance,
27 as these are the resistance values that we are supplied with
37 capella,aset-resistance-ohms = <100000>;
|
| /Linux-v4.19/Documentation/devicetree/bindings/input/touchscreen/ |
| D | ad7879.txt | 10 - adi,resistance-plate-x : total resistance of X-plate (for pressure
47 adi,resistance-plate-x = <120>;
65 adi,resistance-plate-x = <120>;
|
| D | ti-tsc-adc.txt | 8 ti,x-plate-resistance: X plate resistance
71 ti,x-plate-resistance = <200>;
|
| D | bu21029.txt | 8 - rohm,x-plate-ohms : x-plate resistance in Ohm
|
| D | tsc2007.txt | 6 - ti,x-plate-ohms: X-plate resistance in ohms.
|
| D | tsc2005.txt | 13 - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates
|
| /Linux-v4.19/drivers/iio/chemical/ |
| D | ams-iaq-core.c | 24 __be32 resistance; member
115 *val = be32_to_cpu(data->buffer.resistance); in ams_iaqcore_read_raw()
|
| /Linux-v4.19/Documentation/hwmon/ |
| D | ntc_thermistor | 26 that requires users to provide the resistance and lookup the corresponding
86 are suitable or the user can get the resistance directly, the user should
|
| D | ina3221 | 26 shunt[123]_resistor Shunt resistance(uOhm) channels
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/afe/ |
| D | current-sense-amplifier.txt | 12 - sense-resistor-micro-ohms : The sense resistance in microohms.
|
| D | current-sense-shunt.txt | 12 - shunt-resistor-micro-ohms : The shunt resistance in microohms.
|
| D | voltage-divider.txt | 5 interesting voltage is often the voltage over the full resistance
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/dac/ |
| D | dpot-dac.txt | 4 current dpot wiper setting and the maximum resistance of the dpot. The
|
| /Linux-v4.19/Documentation/devicetree/bindings/power/supply/ |
| D | qcom,coincell-charger.txt | 20 Definition: resistance (in ohms) for current-limiting resistor
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/adc/ |
| D | vf610-adc.txt | 22 source resistance (R_as) and capacitance (C_as). Refer the datasheet's
|
| /Linux-v4.19/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-health-afe440x | 32 Get and set the resistance and the capacitance settings for the
|
| /Linux-v4.19/Documentation/devicetree/bindings/thermal/ |
| D | thermal-generic-adc.txt | 4 one of ADC channel and sensor resistance is read via voltage across the
|
| /Linux-v4.19/Documentation/misc-devices/ |
| D | ad525x_dpot.txt | 6 work with the immediate resistance settings as well as update the saved startup
|
| /Linux-v4.19/Documentation/devicetree/bindings/mfd/ |
| D | twl6040.txt | 58 /* Vibra driver, motor resistance parameters */
|
| /Linux-v4.19/drivers/gpu/drm/msm/dsi/pll/ |
| D | dsi_pll_28nm.c | 53 u32 resistance; member
163 pll_write(base + REG_DSI_28nm_PHY_PLL_LPFR_CFG, lpfr_lut[i].resistance); in dsi_pll_28nm_clk_set_rate()
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | sun8i-a23-evb.dts | 123 * The RX line has a non-populated resistance. In order to use it, you
|
| D | am437x-cm-t43.dts | 398 ti,x-plate-resistance = <200>;
|
| /Linux-v4.19/Documentation/media/v4l-drivers/ |
| D | si476x.rst | 96 0x04 fmagc1 FMAGC1 attenuator resistance
|
| /Linux-v4.19/Documentation/ |
| D | siphash.txt | 189 resistance of HalfSipHash.
|
12
