| /Linux-v4.19/drivers/scsi/aic94xx/ |
| D | aic94xx_scb.c | 54 static void get_lrate_mode(struct asd_phy *phy, u8 oob_mode) in get_lrate_mode() argument
58 switch (oob_mode & 7) { in get_lrate_mode()
79 if (oob_mode & SAS_MODE) in get_lrate_mode()
80 phy->sas_phy.oob_mode = SAS_OOB_MODE; in get_lrate_mode()
81 else if (oob_mode & SATA_MODE) in get_lrate_mode()
82 phy->sas_phy.oob_mode = SATA_OOB_MODE; in get_lrate_mode()
94 u8 oob_mode = dl->status_block[2]; in asd_phy_event_tasklet() local
107 get_lrate_mode(phy, oob_mode); in asd_phy_event_tasklet()
157 && phy->sas_phy.oob_mode == SATA_OOB_MODE) { in asd_get_attached_sas_addr()
653 u8 oob_mode = dl->status_block[2]; in control_phy_tasklet_complete() local
[all …]
|
| D | aic94xx_dev.c | 175 if (dev->port->oob_mode != SATA_OOB_MODE) { in asd_init_target_ddb()
|
| D | aic94xx_task.c | 382 if (dev->port->oob_mode == SAS_OOB_MODE) in asd_build_ata_ascb()
|
| D | aic94xx_hwi.c | 98 sas_phy->oob_mode = OOB_NOT_CONNECTED; in asd_init_phy()
|
| /Linux-v4.19/drivers/scsi/libsas/ |
| D | sas_dump.c | 61 SAS_DPRINTK("port%d: oob_mode:0x%x\n", port->id, port->oob_mode); in sas_dump_port()
|
| D | sas_port.c | 169 port->oob_mode = phy->oob_mode; in sas_form_port()
252 port->oob_mode = 0; in sas_deform_port()
|
| D | sas_internal.h | 59 int sas_show_oob_mode(enum sas_oob_mode oob_mode, char *buf);
|
| D | sas_discover.c | 90 if (dev->frame_rcvd[0] == 0x34 && port->oob_mode == SATA_OOB_MODE) { in sas_get_port_device()
|
| /Linux-v4.19/include/scsi/ |
| D | libsas.h | 278 enum sas_oob_mode oob_mode; member
339 enum sas_oob_mode oob_mode; member
449 phy->oob_mode = OOB_NOT_CONNECTED; in sas_phy_disconnected()
|
| /Linux-v4.19/drivers/net/wireless/ath/wil6210/ |
| D | main.c | 37 static u8 oob_mode; variable
38 module_param(oob_mode, byte, 0444);
39 MODULE_PARM_DESC(oob_mode,
1559 wil_set_oob_mode(wil, oob_mode); in wil_reset()
|
| /Linux-v4.19/Documentation/scsi/ |
| D | libsas.txt | 68 class, proto, type, role, oob_mode, linkrate -- must be set
69 oob_mode -- you set this when OOB has finished and then notify
292 PHYE_OOB_DONE -- OOB went fine and oob_mode is valid
|
| /Linux-v4.19/drivers/scsi/isci/ |
| D | port.c | 190 iphy->sas_phy.oob_mode = SATA_OOB_MODE; in isci_port_link_up()
208 iphy->sas_phy.oob_mode = SAS_OOB_MODE; in isci_port_link_up()
|
| D | phy.c | 1415 iphy->sas_phy.oob_mode = OOB_NOT_CONNECTED; in isci_phy_init()
|
| /Linux-v4.19/drivers/scsi/mvsas/ |
| D | mv_init.c | 105 sas_phy->oob_mode = OOB_NOT_CONNECTED; in mvs_phy_init()
|
| D | mv_sas.c | 1045 sas_phy->oob_mode = SATA_OOB_MODE; in mvs_update_phyinfo()
1073 sas_phy->oob_mode = SAS_OOB_MODE; in mvs_update_phyinfo()
|
| /Linux-v4.19/drivers/scsi/hisi_sas/ |
| D | hisi_sas_v3_hw.c | 1204 sas_phy->oob_mode = SATA_OOB_MODE; in phy_up_v3_hw()
1227 sas_phy->oob_mode = SAS_OOB_MODE; in phy_up_v3_hw()
|
| D | hisi_sas_v2_hw.c | 2703 sas_phy->oob_mode = SAS_OOB_MODE; in phy_up_v2_hw()
3274 sas_phy->oob_mode = SATA_OOB_MODE; in sata_int_v2_hw()
|
| D | hisi_sas_v1_hw.c | 1413 sas_phy->oob_mode = SAS_OOB_MODE; in int_phyup_v1_hw()
|
| D | hisi_sas_main.c | 764 sas_phy->oob_mode = OOB_NOT_CONNECTED; in hisi_sas_phy_init()
|
| /Linux-v4.19/drivers/scsi/pm8001/ |
| D | pm8001_init.c | 132 sas_phy->oob_mode = OOB_NOT_CONNECTED; in pm8001_phy_init()
|
| D | pm8001_hwi.c | 3316 && phy->sas_phy.oob_mode == SATA_OOB_MODE) { in pm8001_get_attached_sas_addr()
3426 phy->sas_phy.oob_mode = SAS_OOB_MODE; in hw_event_sas_phy_up()
3471 phy->sas_phy.oob_mode = SATA_OOB_MODE; in hw_event_sata_phy_up()
|
| D | pm80xx_hwi.c | 2893 phy->sas_phy.oob_mode = SAS_OOB_MODE; in hw_event_port_recover()
2968 phy->sas_phy.oob_mode = SAS_OOB_MODE; in hw_event_sas_phy_up()
3016 phy->sas_phy.oob_mode = SATA_OOB_MODE; in hw_event_sata_phy_up()
|
