Searched refs:muxmode (Results 1 – 12 of 12) sorted by relevance
| /Linux-v4.19/drivers/ata/ |
| D | sata_gemini.c | 38 enum gemini_muxmode muxmode; member
133 if ((sg->muxmode == GEMINI_MUXMODE_2) && in gemini_sata_bridge_enabled()
136 if ((sg->muxmode == GEMINI_MUXMODE_3) && in gemini_sata_bridge_enabled()
146 return sg->muxmode; in gemini_sata_get_muxmode()
160 if (sg->muxmode == GEMINI_MUXMODE_2) in gemini_sata_setup_bridge()
166 if (sg->muxmode == GEMINI_MUXMODE_3) in gemini_sata_setup_bridge()
321 enum gemini_muxmode muxmode; in gemini_sata_probe() local
361 ret = of_property_read_u32(np, "cortina,gemini-ata-muxmode", &muxmode); in gemini_sata_probe()
366 if (muxmode > GEMINI_MUXMODE_3) { in gemini_sata_probe()
367 dev_err(dev, "illegal muxmode %d\n", muxmode); in gemini_sata_probe()
[all …]
|
| D | pata_ftide010.c | 355 enum gemini_muxmode muxmode; in pata_ftide010_gemini_init() local
363 muxmode = gemini_sata_get_muxmode(sg); in pata_ftide010_gemini_init()
391 switch (muxmode) { in pata_ftide010_gemini_init()
414 switch (muxmode) { in pata_ftide010_gemini_init()
|
| /Linux-v4.19/Documentation/devicetree/bindings/ata/ |
| D | cortina,gemini-sata-bridge.txt | 16 - cortina,gemini-ata-muxmode: tell the desired multiplexing mode for
35 The muxmode setting decides whether ATA0 or ATA1 is brought out,
52 cortina,gemini-ata-muxmode = <3>;
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | gemini-dlink-dns-313.dts | 272 /* The ROM uses this muxmode */
273 cortina,gemini-ata-muxmode = <0>;
|
| D | gemini-nas4220b.dts | 178 cortina,gemini-ata-muxmode = <0>;
|
| D | gemini-sl93512r.dts | 266 cortina,gemini-ata-muxmode = <0>;
|
| D | gemini-sq201.dts | 262 cortina,gemini-ata-muxmode = <0>;
|
| D | gemini-dlink-dir-685.dts | 379 cortina,gemini-ata-muxmode = <0>;
|
| /Linux-v4.19/drivers/video/fbdev/aty/ |
| D | mach64_gx.c | 294 int muxmode = 0; in aty_set_dac_ATT21C498() local
303 muxmode = 1; in aty_set_dac_ATT21C498()
329 return muxmode; in aty_set_dac_ATT21C498()
|
| /Linux-v4.19/drivers/pinctrl/ |
| D | pinctrl-tb10x.c | 619 int muxmode = -1; in tb10x_gpio_request_enable() local
650 muxmode = mode; in tb10x_gpio_request_enable()
680 tb10x_pinctrl_set_config(state, muxport, muxmode); in tb10x_gpio_request_enable()
|
| /Linux-v4.19/drivers/media/platform/davinci/ |
| D | vpif_display.c | 55 static void vpif_config_addr(struct channel_obj *ch, int muxmode);
561 static void vpif_config_addr(struct channel_obj *ch, int muxmode) in vpif_config_addr() argument
568 if (2 == muxmode) in vpif_config_addr()
|
| D | vpif_capture.c | 56 static void vpif_config_addr(struct channel_obj *ch, int muxmode);
646 static void vpif_config_addr(struct channel_obj *ch, int muxmode) in vpif_config_addr() argument
656 else if (2 == muxmode) in vpif_config_addr()
|
