Searched refs:motor (Results 1 – 18 of 18) sorted by relevance
| /Linux-v4.19/Documentation/devicetree/bindings/mfd/ |
| D | twl6040.txt | 27 - vddvibl-supply: Regulator for the left vibra motor
28 - vddvibr-supply: Regulator for the right vibra motor
33 - ti,viblmotor-res: Resistance parameter for left motor
34 - ti,viblmotor-res: Resistance parameter for right motor
53 /* regulators for vibra motor */
58 /* Vibra driver, motor resistance parameters */
|
| D | max77693.txt | 29 - haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide
35 - haptic-supply : power supply for the haptic motor
|
| /Linux-v4.19/Documentation/devicetree/bindings/input/ |
| D | regulator-haptic.txt | 5 - haptic-supply : Power supply to the haptic motor.
8 - max-microvolt : The maximum voltage value supplied to the haptic motor.
11 - min-microvolt : The minimum voltage value supplied to the haptic motor.
|
| /Linux-v4.19/drivers/of/unittest-data/ |
| D | overlay_base.dts | 30 spin_ctrl_1: motor-1 {
31 compatible = "ot,ferris-wheel-motor";
35 spin_ctrl_2: motor-8 {
36 compatible = "ot,roller-coaster-motor";
|
| D | overlay_bad_phandle.dts | 9 // in the base tree for motor-1.
10 spin_ctrl_1_conflict: motor-1 {
|
| /Linux-v4.19/include/linux/ |
| D | amifd.h | 55 int motor; /* true when motor is at speed */ member
|
| /Linux-v4.19/Documentation/devicetree/bindings/timer/ |
| D | nxp,tpm-timer.txt | 4 and the generation of PWM signals to control electric motor and power
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | sun4i-a10-dserve-dsrv9703c.dts | 78 reg_motor: reg-motor {
80 regulator-name = "vcc-motor";
|
| D | omap4-sdp.dts | 384 /* regulators for vibra motor */
389 /* Vibra driver, motor resistance parameters */
|
| D | da850-lego-ev3.dts | 130 * the sensor (input) ports, the motor (output) ports and the A/DC.
|
| D | lpc32xx.dtsi | 299 compatible = "nxp,lpc3220-motor-pwm";
|
| /Linux-v4.19/drivers/block/ |
| D | amiflop.c | 290 if (unit[drive].motor == 1) in fd_select()
343 if (!unit[nr].motor) { in fd_motor_on()
344 unit[nr].motor = 1; in fd_motor_on()
382 unit[drive].motor = 0; in fd_motor_off()
1580 unit[drive].motor = 0; in fd_probe()
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/adc/ |
| D | st,stm32-dfsdm-adc.txt | 7 - Sigma delta modulators (motor control, metering...)
|
| /Linux-v4.19/Documentation/i2c/busses/ |
| D | i2c-parport | 158 stepper motor card with the simple commands which are in the original
|
| /Linux-v4.19/drivers/input/joystick/ |
| D | Kconfig | 352 To drive rumble motor a dedicated power supply is required.
|
| /Linux-v4.19/Documentation/media/uapi/v4l/ |
| D | vidioc-queryctrl.rst | 477 action (e. g. motor control) but no meaningful value can be
|
| /Linux-v4.19/Documentation/x86/ |
| D | boot.txt | 996 switch off the floppy motor before running the kernel, since the
997 kernel boot leaves interrupts off and thus the motor will not be
|
| /Linux-v4.19/ |
| D | CREDITS | 71 E: tim_alpaerts@toyota-motor-europe.com
|
