| /Linux-v4.19/Documentation/fb/ |
| D | viafb.modes | 14 # Scan Frequency 31.469 kHz 59.94 Hz
29 # D: 25.175 MHz, H: 31.469 kHz, V: 59.94 Hz
32 # D: 24.823 MHz, H: 39.780 kHz, V: 60.00 Hz
39 # Scan Frequency 37.500 kHz 75.00 Hz
53 # D: 31.50 MHz, H: 37.500 kHz, V: 75.00 Hz
60 # Scan Frequency 43.269 kHz 85.00 Hz
74 # D: 36.000 MHz, H: 43.269 kHz, V: 85.00 Hz
81 # Scan Frequency 50.900 kHz 100.00 Hz
95 # D: 43.163 MHz, H: 50.900 kHz, V: 100.00 Hz
102 # Scan Frequency 61.800 kHz 120.00 Hz
[all …]
|
| /Linux-v4.19/Documentation/devicetree/bindings/clock/ |
| D | lpc1850-creg-clk.txt | 5 32 kHz oscillator driver with power up/down and clock gating. Next
6 is a fixed divider that creates a 1 kHz clock from the 32 kHz osc.
9 The 32 kHz can also be routed to other peripherials to enable low
21 Shall contain a phandle to the fixed 32 kHz crystal.
28 0 1 kHz clock
29 1 32 kHz Oscillator
|
| /Linux-v4.19/Documentation/i2c/busses/ |
| D | i2c-ismt | 17 Specify the bus speed in kHz.
20 80 kHz
21 100 kHz
22 400 kHz
23 1000 kHz
|
| /Linux-v4.19/Documentation/arm/sunxi/ |
| D | clocks.txt | 17 24MHz 32kHz
25 When you are about to suspend, you switch the CPU Mux to the 32kHz
28 24Mhz 32kHz
38 32kHz
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | imx6q.dtsi | 25 /* kHz uV */
33 /* ARM kHz SOC-PU uV */
60 /* kHz uV */
68 /* ARM kHz SOC-PU uV */
94 /* kHz uV */
102 /* ARM kHz SOC-PU uV */
128 /* kHz uV */
136 /* ARM kHz SOC-PU uV */
|
| D | highbank.dts | 41 /* kHz ignored */
60 /* kHz ignored */
79 /* kHz ignored */
98 /* kHz ignored */
|
| D | imx6q-cm-fx6.dts | 175 /* kHz uV */
182 /* ARM kHz SOC-PU uV */
197 /* kHz uV */
204 /* ARM kHz SOC-PU uV */
219 /* kHz uV */
226 /* ARM kHz SOC-PU uV */
241 /* kHz uV */
248 /* ARM kHz SOC-PU uV */
|
| D | imx6dl.dtsi | 24 /* kHz uV */
30 /* ARM kHz SOC-PU uV */
55 /* kHz uV */
61 /* ARM kHz SOC-PU uV */
|
| /Linux-v4.19/Documentation/sound/cards/ |
| D | audiophile-usb.rst | 48 * sample rate from 8kHz to 96kHz
57 * 16-bit/48kHz ==> 4 channels in + 4 channels out
61 * 24-bit/48kHz ==> 4 channels in + 2 channels out,
66 * 24-bit/96kHz ==> 2 channels in _or_ 2 channels out (half duplex only)
197 - 16bits 48kHz mode with Di disabled
204 - 16bits 48kHz mode with Di enabled
234 - 24bits 48kHz mode with Di disabled
241 - 24bits 48kHz mode with Di enabled
249 - 24bits 96kHz mode
266 - 16bits 48kHz mode with only the Do port enabled
[all …]
|
| D | hdspm.rst | 143 * Values -- "AutoSync", "Internal 32.0 kHz", "Internal 44.1 kHz",
144 "Internal 48.0 kHz", "Internal 64.0 kHz", "Internal 88.2 kHz",
145 "Internal 96.0 kHz"
|
| /Linux-v4.19/Documentation/media/uapi/dvb/ |
| D | fe-set-tone.rst | 12 FE_SET_TONE - Sets/resets the generation of the continuous 22kHz tone.
35 This ioctl is used to set the generation of the continuous 22kHz tone.
39 to send a 22kHz tone in order to select between high/low band on some
|
| /Linux-v4.19/drivers/mtd/nand/raw/ |
| D | tango_nand.c | 483 static u32 to_ticks(int kHz, int ps) in to_ticks() argument
485 return DIV_ROUND_UP_ULL((u64)kHz * ps, NSEC_PER_SEC); in to_ticks()
496 int kHz = nfc->freq_kHz; in tango_set_timings() local
504 Trdy = to_ticks(kHz, sdr->tCEA_max - sdr->tREA_max); in tango_set_timings()
505 Textw = to_ticks(kHz, sdr->tWB_max); in tango_set_timings()
506 Twc = to_ticks(kHz, sdr->tWC_min); in tango_set_timings()
507 Twpw = to_ticks(kHz, sdr->tWC_min - sdr->tWP_min); in tango_set_timings()
509 Tacc = to_ticks(kHz, sdr->tREA_max); in tango_set_timings()
510 Thold = to_ticks(kHz, sdr->tREH_min); in tango_set_timings()
511 Trpw = to_ticks(kHz, sdr->tRC_min - sdr->tREH_min); in tango_set_timings()
[all …]
|
| /Linux-v4.19/drivers/media/usb/dvb-usb/ |
| D | vp7045-fe.c | 165 .frequency_min_hz = 44250 * kHz,
166 .frequency_max_hz = 867250 * kHz,
167 .frequency_stepsize_hz = 1 * kHz,
|
| D | dtt200u-fe.c | 233 .frequency_min_hz = 44250 * kHz,
234 .frequency_max_hz = 867250 * kHz,
235 .frequency_stepsize_hz = 250 * kHz,
|
| /Linux-v4.19/drivers/media/dvb-frontends/ |
| D | dvb_dummy_fe.c | 174 .frequency_max_hz = 863250 * kHz,
235 .frequency_stepsize_hz = 250 * kHz,
236 .frequency_tolerance_hz = 29500 * kHz,
|
| /Linux-v4.19/Documentation/hwmon/ |
| D | mcp3021 | 27 compatible interface. Standard (100 kHz) and Fast (400 kHz) I2C modes are
|
| D | adt7411 | 36 fast_sampling - Sample at 22.5 kHz instead of 1.4 kHz, but drop filters
|
| D | g760a | 20 cycle counts of an assumed 32kHz clock source.
26 from the measured speed pulse period by assuming again a 32kHz clock
|
| /Linux-v4.19/Documentation/devicetree/bindings/leds/backlight/ |
| D | pm8941-wled.txt | 19 - qcom,switching-freq: kHz; switching frequency; one of:
22 default: 1600kHz
|
| /Linux-v4.19/Documentation/devicetree/bindings/rtc/ |
| D | ingenic,jz4740-rtc.txt | 18 at 32 kHz)
20 time (default 100ms; range 0-2s if RTC clock at 32 kHz)
|
| /Linux-v4.19/Documentation/devicetree/bindings/cpufreq/ |
| D | arm_big_little_dt.txt | 33 /* kHz uV */
52 /* kHz uV */
|
| /Linux-v4.19/Documentation/devicetree/bindings/mfd/ |
| D | mxs-lradc.txt | 18 2 kHz and its default is 2 (= 1 ms)
20 1 ... 2047. It counts at 2 kHz and its default is
|
| /Linux-v4.19/Documentation/devicetree/bindings/sound/ |
| D | st,stm32-i2s.txt | 15 "x8k": I2S parent clock for sampling rates multiple of 8kHz.
16 "x11k": I2S parent clock for sampling rates multiple of 11.025kHz.
|
| D | gtm601.txt | 3 This device has no configuration interface. Sample rate is fixed - 8kHz.
|
| /Linux-v4.19/drivers/media/tuners/ |
| D | qt1010_priv.h | 74 #define QT1010_STEP (125 * kHz) /*
|
