Home
last modified time | relevance | path

Searched refs:iomux (Results 1 – 16 of 16) sorted by relevance

/Linux-v4.19/arch/arc/boot/dts/
Dabilis_tb100.dtsi41 iomux: iomux@FF10601c { label
175 gpio-ranges = <&iomux 0 0 0>;
188 gpio-ranges = <&iomux 0 0 0>;
201 gpio-ranges = <&iomux 0 0 0>;
214 gpio-ranges = <&iomux 0 0 0>;
227 gpio-ranges = <&iomux 0 0 0>;
240 gpio-ranges = <&iomux 0 0 0>;
253 gpio-ranges = <&iomux 0 0 0>;
266 gpio-ranges = <&iomux 0 0 0>;
279 gpio-ranges = <&iomux 0 0 0>;
[all …]
Dabilis_tb101.dtsi41 iomux: iomux@FF10601c { label
184 gpio-ranges = <&iomux 0 0 0>;
197 gpio-ranges = <&iomux 0 0 0>;
210 gpio-ranges = <&iomux 0 0 0>;
223 gpio-ranges = <&iomux 0 0 0>;
236 gpio-ranges = <&iomux 0 0 0>;
249 gpio-ranges = <&iomux 0 0 0>;
262 gpio-ranges = <&iomux 0 0 0>;
275 gpio-ranges = <&iomux 0 0 0>;
288 gpio-ranges = <&iomux 0 0 0>;
[all …]
Dabilis_tb10x.dtsi78 iomux: iomux@FF10601c { label
79 compatible = "abilis,tb10x-iomux";
/Linux-v4.19/Documentation/devicetree/bindings/pinctrl/
Dabilis,tb10x-iomux.txt7 - compatible: should be "abilis,tb10x-iomux";
52 iomux: iomux@ff10601c {
53 compatible = "abilis,tb10x-iomux";
78 gpio-ranges = <&iomux 0 0>;
Dfsl,imx27-pinctrl.txt55 The iomux controller has gpio child nodes which are embedded in the iomux
56 control registers. They have to be defined as child nodes of the iomux device
58 properties for the iomux device node are required.
Drockchip,pinctrl.txt21 Required properties for iomux controller:
39 Optional properties for iomux controller:
41 as some SoCs carry parts of the iomux controller registers there.
45 Deprecated properties for iomux controller:
46 - reg: first element is the general register space of the iomux controller
53 - reg: register of the gpio bank (different than the iomux registerset)
Dfsl,imx-pinctrl.txt20 Required properties for iomux controller:
46 1. We have pin function node defined under iomux controller node to represent
Dfsl,imx7d-pinctrl.txt58 any of the iomux controllers. For example the I2C1 IP can use SCL pad from
Datmel,at91-pinctrl.txt20 Required properties for iomux controller:
/Linux-v4.19/Documentation/devicetree/bindings/sound/
Dqcom,apq8016-sbc.txt15 * "mic-iomux"
16 * "spkr-iomux"
54 reg-names = "mic-iomux", "spkr-iomux";
/Linux-v4.19/arch/arm/mach-imx/
DMakefile11 obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o iomux-imx31.o ehci-imx31.o
17 obj-$(CONFIG_IMX_HAVE_IOMUX_V1) += iomux-v1.o
18 obj-$(CONFIG_ARCH_MXC_IOMUX_V3) += iomux-v3.o
/Linux-v4.19/drivers/pinctrl/
Dpinctrl-rockchip.c159 struct rockchip_iomux iomux[4]; member
179 .iomux = { \
192 .iomux = { \
205 .iomux = { \
226 .iomux = { \
252 .iomux = { \
276 .iomux = { \
1129 if (bank->iomux[iomux_num].type & IOMUX_UNROUTED) { in rockchip_get_mux()
1134 if (bank->iomux[iomux_num].type & IOMUX_GPIO_ONLY) in rockchip_get_mux()
1137 regmap = (bank->iomux[iomux_num].type & IOMUX_SOURCE_PMU) in rockchip_get_mux()
[all …]
/Linux-v4.19/Documentation/devicetree/bindings/display/rockchip/
Dinno_hdmi-rockchip.txt17 Switch the iomux of HPD/CEC pins to HDMI function.
/Linux-v4.19/Documentation/devicetree/bindings/gpio/
Dabilis,tb10x-gpio.txt33 gpio-ranges = <&iomux 0 0 0>;
/Linux-v4.19/arch/arm64/boot/dts/qcom/
Dapq8016-sbc.dtsi442 reg-names = "mic-iomux", "spkr-iomux";
/Linux-v4.19/Documentation/devicetree/bindings/arm/
Dfsl.txt63 No iomux setup is done for these boards, so this must have been configured