| /Linux-v4.19/Documentation/media/uapi/dvb/ |
| D | fe-enable-high-lnb-voltage.rst | 12 FE_ENABLE_HIGH_LNB_VOLTAGE - Select output DC level between normal LNBf voltages or higher LNBf - v…
33 - >0 - enables slightly higher voltages instead of 13/18V, in order
40 Select output DC level between normal LNBf voltages or higher LNBf
41 voltages between 0 (normal) or a value grater than 0 for higher
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | kirkwood-rd88f6281-a.dts | 8 * higher stepping of the SoC. The ethernet switch does not have a
16 model = "Marvell RD88f6281 Reference design, with A0 or higher SoC";
|
| D | exynos4412-prime.dtsi | 10 * Exynos4412 Prime SoC revision supports higher CPU frequencies than
|
| /Linux-v4.19/net/lapb/ |
| D | Kconfig | 11 it is used to transport higher level protocols (mostly X.25 Packet
12 Layer, the higher part of X.25, but others are possible as well).
|
| /Linux-v4.19/arch/x86/power/ |
| D | hibernate_asm_32.S | 36 jecxz 1f # cr4 Pentium and higher, skip if zero
66 jecxz 1f # cr4 Pentium and higher, skip if zero
|
| /Linux-v4.19/arch/powerpc/platforms/maple/ |
| D | pci.c | 39 static int __init fixup_one_level_bus_range(struct device_node *node, int higher) in fixup_one_level_bus_range() argument
53 if (bus_range[1] > higher) in fixup_one_level_bus_range()
54 higher = bus_range[1]; in fixup_one_level_bus_range()
56 higher = fixup_one_level_bus_range(node->child, higher); in fixup_one_level_bus_range()
58 return higher; in fixup_one_level_bus_range()
|
| /Linux-v4.19/Documentation/devicetree/bindings/thermal/ |
| D | nvidia,tegra124-soctherm.txt | 41 Bigger value indicates higher priority, In general, higher priority
43 thermal alarms are given higher priority, and ensure that there is
60 shut down temperature. Once the temperature of this thermal zone is higher
63 temperature. Once the the temperature of this thermal zone is higher
|
| D | imx-thermal.txt | 9 i.MX6Q has one IRQ which will be triggered when temperature is higher than high threshold,
12 is higher than panic threshold, system will auto reboot by SRC module.
|
| /Linux-v4.19/Documentation/devicetree/bindings/display/ |
| D | ssd1307fb.txt | 28 This needs to be the higher, the higher the capacitance
|
| /Linux-v4.19/Documentation/ABI/testing/ |
| D | sysfs-driver-xen-blkfront | 8 is 32 - higher value means more potential throughput but more
|
| D | sysfs-platform-hidma-mgmt | 64 Choosing a higher number gives better performance but
85 Choosing a higher number gives better performance but
|
| D | sysfs-devices-power_state | 17 higher-power (lower-number) states may also be ON because of
|
| /Linux-v4.19/Documentation/filesystems/ |
| D | ecryptfs.txt | 23 1.0 or higher), obtainable from
70 then behavior is undefined. Do not run eCryptfs in higher verbosity
|
| /Linux-v4.19/Documentation/hwmon/ |
| D | adt7462 | 61 point2: Set the pwm speed at a higher temperature bound.
63 The ADT7462 will scale the pwm between the lower and higher pwm speed when
|
| D | nct6775 | 71 configuration. An alarm is triggered when the temperature gets higher than
150 speed increases (if temperature is higher that desired) or decreases (if
184 points should be set to higher temperatures and higher pwm values to achieve
185 higher fan speeds with increasing temperature. The last data point reflects
|
| D | adt7470 | 60 point2: Set the pwm speed at a higher temperature bound.
62 The ADT7470 will scale the pwm between the lower and higher pwm speed when
|
| D | w83627ehf | 59 configurable. temp4 and higher attributes are only reported if its temperature
65 degC for temp1 and and 0.5 degC for temp2 and temp3. For temp4 and higher,
67 An alarm is triggered when the temperature gets higher than high limit;
138 fan speed increases (temp is higher) or decreases if lower than desired.
|
| /Linux-v4.19/arch/arm/crypto/ |
| D | Makefile | 27 $(warning These CRC Extensions modules need binutils 2.23 or higher)
37 $(warning These ARMv8 Crypto Extensions modules need binutils 2.23 or higher)
|
| /Linux-v4.19/arch/arc/ |
| D | Kconfig.debug | 10 on the VM subsystem for higher order allocations.
|
| /Linux-v4.19/Documentation/driver-api/80211/ |
| D | introduction.rst | 13 higher-level overview.
|
| /Linux-v4.19/arch/powerpc/platforms/powermac/ |
| D | pci.c | 63 static int __init fixup_one_level_bus_range(struct device_node *node, int higher) in fixup_one_level_bus_range() argument
77 if (bus_range[1] > higher) in fixup_one_level_bus_range()
78 higher = bus_range[1]; in fixup_one_level_bus_range()
80 higher = fixup_one_level_bus_range(node->child, higher); in fixup_one_level_bus_range()
82 return higher; in fixup_one_level_bus_range()
|
| /Linux-v4.19/Documentation/vm/ |
| D | zsmalloc.rst | 9 never attempts higher order page allocation which is very likely to
17 pages act as a single higher-order page i.e. an object can span 0-order
|
| /Linux-v4.19/tools/testing/selftests/powerpc/include/ |
| D | basic_asm.h | 10 ori reg, reg, (expr)@higher; \
|
| /Linux-v4.19/Documentation/devicetree/bindings/sound/ |
| D | da7219.txt | 46 - dlg,micbias-pulse-lvl : Mic bias higher voltage pulse level (mV).
48 - dlg,micbias-pulse-time : Mic bias higher voltage pulse duration (ms)
|
| /Linux-v4.19/tools/perf/Documentation/ |
| D | perf.txt | 27 Setup buildid cache directory. It has higher priority than
|
