Home
last modified time | relevance | path

Searched refs:e_dbg (Results 1 – 12 of 12) sorted by relevance

/Linux-v4.19/drivers/net/ethernet/intel/e1000e/
Dmac.c118 e_dbg("Programming MAC Address into RAR[0]\n"); in e1000e_init_rx_addrs()
123 e_dbg("Clearing RAR[1-%u]\n", rar_count - 1); in e1000e_init_rx_addrs()
158 e_dbg("NVM Read Error\n"); in e1000_check_alt_mac_addr_generic()
173 e_dbg("NVM Read Error\n"); in e1000_check_alt_mac_addr_generic()
183 e_dbg("Ignoring Alternate Mac Address with MC bit set\n"); in e1000_check_alt_mac_addr_generic()
443 e_dbg("Error configuring flow control\n"); in e1000e_check_for_copper_link()
485 e_dbg("NOT Rx'ing /C/, disable AutoNeg and force link.\n"); in e1000e_check_for_fiber_link()
498 e_dbg("Error configuring flow control\n"); in e1000e_check_for_fiber_link()
507 e_dbg("Rx'ing /C/, enable AutoNeg and stop forcing link.\n"); in e1000e_check_for_fiber_link()
548 e_dbg("NOT Rx'ing /C/, disable AutoNeg and force link.\n"); in e1000e_check_for_serdes_link()
[all …]
Dnvm.c169 e_dbg("Could not acquire NVM grant\n"); in e1000e_acquire_nvm()
274 e_dbg("SPI NVM Status error\n"); in e1000_ready_nvm_eeprom()
302 e_dbg("nvm parameter(s) out of bounds\n"); in e1000e_read_nvm_eerd()
313 e_dbg("NVM read error: %d\n", ret_val); in e1000e_read_nvm_eerd()
346 e_dbg("nvm parameter(s) out of bounds\n"); in e1000e_write_nvm_spi()
421 e_dbg("PBA string buffer was null\n"); in e1000_read_pba_string_generic()
427 e_dbg("NVM Read Error\n"); in e1000_read_pba_string_generic()
433 e_dbg("NVM Read Error\n"); in e1000_read_pba_string_generic()
442 e_dbg("NVM PBA number is not stored as string\n"); in e1000_read_pba_string_generic()
446 e_dbg("PBA string buffer too small\n"); in e1000_read_pba_string_generic()
[all …]
Dphy.c124 e_dbg("PHY Address %d is out of range\n", offset); in e1000e_read_phy_reg_mdic()
149 e_dbg("MDI Read did not complete\n"); in e1000e_read_phy_reg_mdic()
153 e_dbg("MDI Error\n"); in e1000e_read_phy_reg_mdic()
157 e_dbg("MDI Read offset error - requested %d, returned %d\n", in e1000e_read_phy_reg_mdic()
187 e_dbg("PHY Address %d is out of range\n", offset); in e1000e_write_phy_reg_mdic()
213 e_dbg("MDI Write did not complete\n"); in e1000e_write_phy_reg_mdic()
217 e_dbg("MDI Error\n"); in e1000e_write_phy_reg_mdic()
221 e_dbg("MDI Write offset error - requested %d, returned %d\n", in e1000e_write_phy_reg_mdic()
298 e_dbg("Setting page 0x%x\n", page); in e1000_set_page_igp()
740 e_dbg("Error committing the PHY changes\n"); in e1000e_copper_link_setup_m88()
[all …]
D82571.c85 e_dbg("Error getting PHY ID\n"); in e1000_init_phy_params_82571()
111 e_dbg("PHY ID unknown: type = 0x%08x\n", phy->id); in e1000_init_phy_params_82571()
302 e_dbg("Please update your 82571 Bootagent\n"); in e1000_init_mac_params_82571()
462 e_dbg("Driver can't access device - SMBI bit is set.\n"); in e1000_get_hw_semaphore_82571()
480 e_dbg("Driver can't access the NVM\n"); in e1000_get_hw_semaphore_82571()
530 e_dbg("Driver can't access the PHY\n"); in e1000_get_hw_semaphore_82573()
817 e_dbg("nvm parameter(s) out of bounds\n"); in e1000_write_nvm_eewr_82571()
857 e_dbg("MNG configuration cycle has not completed.\n"); in e1000_get_cfg_done_82571()
951 e_dbg("PCI-E Master disable polling has failed.\n"); in e1000_reset_hw_82571()
953 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw_82571()
[all …]
Dich8lan.c307 e_dbg("Failed to initialize PHY flow\n"); in e1000_init_phy_workarounds_pchlan()
347 e_dbg("Required LANPHYPC toggle blocked by ME\n"); in e1000_init_phy_workarounds_pchlan()
526 e_dbg("Cannot determine PHY addr. Erroring out\n"); in e1000_init_phy_params_ich8lan()
612 e_dbg("ERROR: Flash registers not mapped\n"); in e1000_init_nvm_params_ich8lan()
1008 e_dbg("max_frame_size not set.\n"); in e1000_platform_pm_pch_lpt()
1014 e_dbg("Speed not set.\n"); in e1000_platform_pm_pch_lpt()
1039 e_dbg("Invalid LTR latency scale %d\n", scale); in e1000_platform_pm_pch_lpt()
1110 e_dbg("CABLE_DISCONNECTED %s set after %dmsec\n", in e1000_enable_ulp_lpt_lp()
1194 e_dbg("Error in ULP enable flow: %d\n", ret_val); in e1000_enable_ulp_lpt_lp()
1249 e_dbg("ULP_CONFIG_DONE cleared after %dmsec\n", i * 10); in e1000_disable_ulp_lpt_lp()
[all …]
D80003es2lan.c298 e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n"); in e1000_acquire_swfw_sync_80003es2lan()
507 e_dbg("MNG configuration cycle has not completed.\n"); in e1000_get_cfg_done_80003es2lan()
539 e_dbg("GG82563 PSCR: %X\n", phy_data); in e1000_phy_force_speed_duplex_80003es2lan()
557 e_dbg("Waiting for forced speed/duplex link on GG82563 phy.\n"); in e1000_phy_force_speed_duplex_80003es2lan()
674 e_dbg("PCI-E Master disable polling has failed.\n"); in e1000_reset_hw_80003es2lan()
676 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw_80003es2lan()
691 e_dbg("Issuing a global reset to MAC\n"); in e1000_reset_hw_80003es2lan()
737 e_dbg("Error initializing identification LED\n"); in e1000_init_hw_80003es2lan()
740 e_dbg("Initializing the IEEE VLAN\n"); in e1000_init_hw_80003es2lan()
747 e_dbg("Zeroing the MTA\n"); in e1000_init_hw_80003es2lan()
[all …]
Dmanage.c44 e_dbg("ARC subsystem not valid.\n"); in e1000_mng_enable_host_if()
51 e_dbg("E1000_HOST_EN bit disabled.\n"); in e1000_mng_enable_host_if()
63 e_dbg("Previous command timeout failed.\n"); in e1000_mng_enable_host_if()
Dptp.c238 e_dbg("SYSTIM overflow check at %lld.%09lu\n", in e1000e_systim_overflow_work()
De1000.h30 #define e_dbg(format, arg...) \ macro
Dnetdev.c967 e_dbg("Receive packet consumed multiple buffers\n"); in e1000_clean_rx_irq()
1116 e_dbg("false hang detected, ignoring\n"); in e1000_print_hw_hang()
1352 e_dbg("Packet Split buffers didn't pick up the full packet\n"); in e1000_clean_rx_irq_ps()
1368 e_dbg("Last part of the packet spanning multiple descriptors\n"); in e1000_clean_rx_irq_ps()
3043 e_dbg("failed to enable|disable jumbo frame workaround mode\n"); in e1000_setup_rctl()
4297 e_dbg("failed to disable jumbo frame workaround mode\n"); in e1000e_down()
4450 e_dbg("icr is %08X\n", icr); in e1000_intr_msi_test()
4518 e_dbg("MSI interrupt test succeeded!\n"); in e1000_test_msi_interrupt()
5126 e_dbg("PHY appears hung - resetting\n"); in e1000e_check_82574_phy_workaround()
7283 e_dbg("NVM read error getting WoL initial values: %d\n", ret_val); in e1000_probe()
[all …]
/Linux-v4.19/drivers/net/ethernet/intel/e1000/
De1000_hw.c387 e_dbg("Disabling MWI on 82542 rev 2.0\n"); in e1000_reset_hw()
392 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw()
425 e_dbg("Issuing a global reset to MAC\n"); in e1000_reset_hw()
501 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw()
537 e_dbg("Error Initializing Identification LED\n"); in e1000_init_hw()
545 e_dbg("Initializing the IEEE VLAN\n"); in e1000_init_hw()
552 e_dbg("Disabling MWI on 82542 rev 2.0\n"); in e1000_init_hw()
574 e_dbg("Zeroing the MTA\n"); in e1000_init_hw()
705 e_dbg("EEPROM Read Error\n"); in e1000_setup_link()
729 e_dbg("After fix-ups FlowControl is now = %x\n", hw->fc); in e1000_setup_link()
[all …]
De1000.h316 #define e_dbg(format, arg...) \ macro