Searched refs:conversion (Results 1 – 25 of 137) sorted by relevance
123456
| /Linux-v4.19/Documentation/devicetree/bindings/input/touchscreen/ |
| D | ad7879.txt | 14 - adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us)
34 - adi,conversion-interval: : 0 : convert one time only
48 adi,first-conversion-delay = /bits/ 8 <3>;
52 adi,conversion-interval = /bits/ 8 <255>;
66 adi,first-conversion-delay = /bits/ 8 <3>;
70 adi,conversion-interval = /bits/ 8 <255>;
|
| D | fsl-mx25-tcq.txt | 1 Freescale mx25 TS conversion queue module
3 mx25 touchscreen conversion queue module which controls the ADC unit of the
24 This device includes two conversion queues which can be added as subnodes.
|
| /Linux-v4.19/scripts/coccinelle/misc/ |
| D | boolconv.cocci | 1 /// Remove unneeded conversion to bool
4 //# explicit conversion is overly verbose and unneeded.
78 msg = "WARNING: conversion to bool not needed here"
89 msg = "WARNING: conversion to bool not needed here"
|
| /Linux-v4.19/Documentation/hwmon/ |
| D | lm73 | 26 affects the conversion time of the LM73's analog-to-digital converter.
28 conversion time via the 'update_interval' sysfs attribute for the
42 used to change the conversion time:
71 conversion time actively in use.
73 Mathematically, the resolution can be derived from the conversion time
|
| D | max197 | 29 filled with a pointer to a conversion function, defined like:
33 ctrl is the control byte to write to start a new conversion.
43 3 BIP Unipolar or Bipolar conversion mode
49 * in[0-7]_input: The conversion value for the corresponding channel.
|
| D | ina2xx | 42 programmable conversion times and filtering.
61 bus and shunt voltage conversion times multiplied by the averaging rate. We
62 don't touch the conversion times and only modify the number of averages. The
|
| D | da9055 | 13 multiplexer. The analogue input multiplexer will allow conversion of up to 5
15 the input of the ADC during the conversion.
|
| D | da9052 | 13 multiplexer. The analogue input multiplexer will allow conversion of up to 10
15 the input of the ADC during the conversion.
|
| D | ds1621 | 143 used to change the conversion time:
177 after a write operation provides the conversion time used by the device.
179 Mathematically, the resolution can be derived from the conversion time
187 -> 93.75ms = minimum conversion time
|
| /Linux-v4.19/Documentation/devicetree/bindings/mfd/ |
| D | fsl-imx25-tsadc.txt | 3 This device combines two general purpose conversion queues one used for general
15 conversion queues.
20 This device includes two conversion queues which can be added as subnodes.
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/adc/ |
| D | ti-adc12138.txt | 9 - interrupts: Should contain interrupt for EOC (end of conversion)
10 - clocks: phandle to conversion clock input
19 - ti,acquisition-time: The number of conversion clock periods for the S/H's
|
| D | vf610-adc.txt | 16 requirements. Three values are required, depending on conversion mode:
21 to be chosen according to the conversion mode and the connected analog
24 C_as as well as conversion modes is 1000ns.
|
| /Linux-v4.19/Documentation/w1/slaves/ |
| D | w1_therm | 14 w1_therm provides basic temperature conversion for ds18*20 devices, and the
24 read sequence will initiate a temperature conversion then provide two
32 temperature conversion at a time. If none of the devices are parasite
36 precision (which would also reduce the conversion time) when reading values.
55 driven when the conversion is taking place, provided the master driver
|
| D | w1_ds2438 | 46 Opening and reading this file initiates the CONVERT_T (temperature conversion)
55 Opening and reading this file initiates the CONVERT_V (voltage conversion)
62 After the voltage conversion the value is returned as decimal ASCII.
|
| /Linux-v4.19/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-vf610 | 5 Specifies the hardware conversion mode used. The three
14 Specifies the hardware conversion mode used within DAC.
|
| D | sysfs-bus-iio-ina2xx-adc | 8 buffer. This synchronizes the in-chip conversion rate with the
14 or repeated, depending on the beat between the capture and conversion
|
| /Linux-v4.19/tools/perf/Documentation/ |
| D | perf-data.txt | 21 It's possible to set data-convert debug variable to get debug messages from conversion,
28 Triggers the CTF conversion, specify the path of CTF data directory.
|
| /Linux-v4.19/Documentation/devicetree/bindings/media/i2c/ |
| D | tvp514x.txt | 6 to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
7 conversion and decoding of NTSC, PAL and SECAM composite and S-video into
|
| /Linux-v4.19/Documentation/driver-api/iio/ |
| D | intro.rst | 9 analog-to-digital conversion (ADC) or digital-to-analog conversion (DAC)
|
| /Linux-v4.19/drivers/gpu/drm/amd/display/dc/basics/ |
| D | Makefile | 27 BASICS = conversion.o fixpt31_32.o \
|
| /Linux-v4.19/drivers/gpu/drm/rcar-du/ |
| D | rcar_du_of_lvds_r8a7793.dts | 3 * rcar_du_of_lvds_r8a7793.dts - Legacy LVDS DT bindings conversion for R8A7793
|
| D | rcar_du_of_lvds_r8a7791.dts | 3 * rcar_du_of_lvds_r8a7791.dts - Legacy LVDS DT bindings conversion for R8A7791
|
| D | rcar_du_of_lvds_r8a7795.dts | 3 * rcar_du_of_lvds_r8a7795.dts - Legacy LVDS DT bindings conversion for R8A7795
|
| D | rcar_du_of_lvds_r8a7796.dts | 3 * rcar_du_of_lvds_r8a7796.dts - Legacy LVDS DT bindings conversion for R8A7796
|
| /Linux-v4.19/Documentation/devicetree/bindings/iio/pressure/ |
| D | hp03.txt | 7 it must be pulled HI before the conversion and
|
123456
