| /Linux-v4.19/drivers/regulator/ |
| D | lp8788-buck.c | 106 static void lp8788_buck1_set_dvs(struct lp8788_buck *buck) in lp8788_buck1_set_dvs() argument
108 struct lp8788_buck1_dvs *dvs = (struct lp8788_buck1_dvs *)buck->dvs; in lp8788_buck1_set_dvs()
119 static void lp8788_buck2_set_dvs(struct lp8788_buck *buck) in lp8788_buck2_set_dvs() argument
121 struct lp8788_buck2_dvs *dvs = (struct lp8788_buck2_dvs *)buck->dvs; in lp8788_buck2_set_dvs()
155 static void lp8788_set_dvs(struct lp8788_buck *buck, enum lp8788_buck_id id) in lp8788_set_dvs() argument
159 lp8788_buck1_set_dvs(buck); in lp8788_set_dvs()
162 lp8788_buck2_set_dvs(buck); in lp8788_set_dvs()
170 lp8788_get_buck_dvs_ctrl_mode(struct lp8788_buck *buck, enum lp8788_buck_id id) in lp8788_get_buck_dvs_ctrl_mode() argument
185 lp8788_read_byte(buck->lp, LP8788_BUCK_DVS_SEL, &val); in lp8788_get_buck_dvs_ctrl_mode()
207 static u8 lp8788_select_buck_vout_addr(struct lp8788_buck *buck, in lp8788_select_buck_vout_addr() argument
[all …]
|
| D | lp3971.c | 175 int buck = rdev_get_id(dev) - LP3971_DCDC1; in lp3971_dcdc_is_enabled() local
176 u16 mask = 1 << (buck * 2); in lp3971_dcdc_is_enabled()
186 int buck = rdev_get_id(dev) - LP3971_DCDC1; in lp3971_dcdc_enable() local
187 u16 mask = 1 << (buck * 2); in lp3971_dcdc_enable()
195 int buck = rdev_get_id(dev) - LP3971_DCDC1; in lp3971_dcdc_disable() local
196 u16 mask = 1 << (buck * 2); in lp3971_dcdc_disable()
204 int buck = rdev_get_id(dev) - LP3971_DCDC1; in lp3971_dcdc_get_voltage_sel() local
207 reg = lp3971_reg_read(lp3971, LP3971_BUCK_TARGET_VOL1_REG(buck)); in lp3971_dcdc_get_voltage_sel()
217 int buck = rdev_get_id(dev) - LP3971_DCDC1; in lp3971_dcdc_set_voltage_sel() local
220 ret = lp3971_set_bits(lp3971, LP3971_BUCK_TARGET_VOL1_REG(buck), in lp3971_dcdc_set_voltage_sel()
[all …]
|
| D | lp3972.c | 321 int buck = rdev_get_id(dev) - LP3972_DCDC1; in lp3972_dcdc_is_enabled() local
322 u16 mask = 1 << (buck * 2); in lp3972_dcdc_is_enabled()
325 val = lp3972_reg_read(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck)); in lp3972_dcdc_is_enabled()
332 int buck = rdev_get_id(dev) - LP3972_DCDC1; in lp3972_dcdc_enable() local
333 u16 mask = 1 << (buck * 2); in lp3972_dcdc_enable()
336 val = lp3972_set_bits(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck), in lp3972_dcdc_enable()
344 int buck = rdev_get_id(dev) - LP3972_DCDC1; in lp3972_dcdc_disable() local
345 u16 mask = 1 << (buck * 2); in lp3972_dcdc_disable()
348 val = lp3972_set_bits(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck), in lp3972_dcdc_disable()
356 int buck = rdev_get_id(dev) - LP3972_DCDC1; in lp3972_dcdc_get_voltage_sel() local
[all …]
|
| D | lp872x.c | 267 enum lp872x_regulator_id buck) in lp872x_select_buck_vout_addr() argument
274 switch (buck) { in lp872x_select_buck_vout_addr()
324 enum lp872x_regulator_id buck = rdev_get_id(rdev); in lp872x_buck_set_voltage_sel() local
331 addr = lp872x_select_buck_vout_addr(lp, buck); in lp872x_buck_set_voltage_sel()
341 enum lp872x_regulator_id buck = rdev_get_id(rdev); in lp872x_buck_get_voltage_sel() local
345 addr = lp872x_select_buck_vout_addr(lp, buck); in lp872x_buck_get_voltage_sel()
360 enum lp872x_regulator_id buck = rdev_get_id(rdev); in lp8725_buck_set_current_limit() local
364 switch (buck) { in lp8725_buck_set_current_limit()
389 enum lp872x_regulator_id buck = rdev_get_id(rdev); in lp8725_buck_get_current_limit() local
393 switch (buck) { in lp8725_buck_get_current_limit()
[all …]
|
| D | max8998.c | 300 int buck = rdev_get_id(rdev); in max8998_set_voltage_buck_sel() local
308 switch (buck) { in max8998_set_voltage_buck_sel()
404 int buck = rdev_get_id(rdev); in max8998_set_voltage_buck_time_sel() local
408 if (buck < MAX8998_BUCK1 || buck > MAX8998_BUCK4) in max8998_set_voltage_buck_time_sel()
411 desc = ldo_voltage_map[buck]; in max8998_set_voltage_buck_time_sel()
|
| /Linux-v4.19/Documentation/devicetree/bindings/mfd/ |
| D | axp20x.txt | 77 DCDC2 : DC-DC buck : vin2-supply
78 DCDC3 : DC-DC buck : vin3-supply
89 DCDC1 : DC-DC buck : vin1-supply
90 DCDC2 : DC-DC buck : vin2-supply
91 DCDC3 : DC-DC buck : vin3-supply
92 DCDC4 : DC-DC buck : vin4-supply
93 DCDC5 : DC-DC buck : vin5-supply
115 DCDC1 : DC-DC buck : vin1-supply
116 DCDC2 : DC-DC buck : vin2-supply : poly-phase capable
117 DCDC3 : DC-DC buck : vin3-supply : poly-phase capable
[all …]
|
| D | tps65086.txt | 18 after their hardware counterparts: buck[1-6],
25 - ti,regulator-step-size-25mv : This is applicable for buck[1-6], set this
28 - ti,regulator-decay : This is applicable for buck[1-6], set this if
|
| D | max8998.txt | 27 for buck 1 dvs. The format of the gpio specifier depends on the gpio
30 for buck 2 dvs. The format of the gpio specifier depends on the gpio
40 - max8998,pmic-buck-voltage-lock: If present, disallows changing of
41 preprogrammed buck dvfs voltages.
|
| D | samsung,sec-core.txt | 37 unwanted buck warm reset (setting buck voltages to default values).
|
| /Linux-v4.19/Documentation/devicetree/bindings/regulator/ |
| D | mt6380-regulator.txt | 5 to its regulator type, buck-<name> and ldo-<name>. The definition for each
11 buck-core1, buck-vcore, buck-vrf
20 mt6380_vcpu_reg: buck-vcore1 {
29 mt6380_vcore_reg: buck-vcore {
36 mt6380_vrf_reg: buck-vrf {
|
| D | samsung,s5m8767.txt | 7 The S5M8767 device provide buck and LDO regulators.
28 - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
31 [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
32 property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
36 If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
38 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
52 - s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
89 s5m8767,pmic-buck-default-dvs-idx = <0>;
91 s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
95 s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
|
| D | samsung,s2mpa01.txt | 7 The S2MPA01 device provide buck and LDO regulators.
26 Optional properties of buck regulator nodes under "regulators" sub-node:
38 - buck{1,6},
39 - buck{2,4},
40 - buck{8,9,10}.
|
| D | samsung,s2mps11.txt | 7 The S2MPS11/13/14/15 and S2MPU02 devices provide buck and LDO regulators.
47 - buck{1,6},
48 - buck{3,4},
49 - buck{7,8,10}.
|
| D | max8997-regulator.txt | 25 [1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
26 property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage'
30 If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
32 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified.
45 that of another buck, which is the side effect of the change (set_voltage).
|
| D | lp872x.txt | 34 LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck)
88 vcc: buck {
|
| /Linux-v4.19/Documentation/devicetree/bindings/sound/ |
| D | qcom,wcd9335.txt | 58 - vdd-buck-supply:
61 Definition: Should contain a reference to the 1.8V buck supply
63 - vdd-buck-sido-supply:
66 Definition: Should contain a reference to the 1.8V SIDO buck supply
117 vdd-buck-supply = <&pm8994_s4>;
119 vdd-buck-sido-supply = <&pm8994_s4>;
|
| /Linux-v4.19/arch/arm64/boot/dts/mediatek/ |
| D | mt6380.dtsi | 14 mt6380_vcpu_reg: buck-vcore1 {
23 mt6380_vcore_reg: buck-vcore {
32 mt6380_vrf_reg: buck-vrf {
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | exynos4412-itop-scp-core.dtsi | 132 s5m8767,pmic-buck-default-dvs-idx = <3>;
134 s5m8767,pmic-buck-dvs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>,
138 s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>,
|
| D | exynos4412-origen.dts | 120 s5m8767,pmic-buck-default-dvs-idx = <3>;
122 s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>,
126 s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>,
|
| D | rk3288-veyron-speedy.dts | 111 buck-5v {
|
| D | rk3288-veyron-jaq.dts | 145 buck-5v {
|
| D | rk3288-veyron-jerry.dts | 108 buck-5v {
|
| D | rk3288-veyron-minnie.dts | 198 buck-5v {
|
| D | exynos5250-spring.dts | 116 s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
120 s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
|
| D | exynos5250-arndale.dts | 195 s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_HIGH>,
198 s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>,
|
