Home
last modified time | relevance | path

Searched refs:boost (Results 1 – 25 of 92) sorted by relevance

1234

/Linux-v4.19/drivers/gpu/drm/nouveau/nvkm/subdev/bios/
Dboost.c33 u32 boost = 0; in nvbios_boostTe() local
37 boost = nvbios_rd32(bios, bit_P.offset + 0x30); in nvbios_boostTe()
39 if (boost) { in nvbios_boostTe()
40 *ver = nvbios_rd08(bios, boost + 0); in nvbios_boostTe()
43 *hdr = nvbios_rd08(bios, boost + 1); in nvbios_boostTe()
44 *cnt = nvbios_rd08(bios, boost + 5); in nvbios_boostTe()
45 *len = nvbios_rd08(bios, boost + 2); in nvbios_boostTe()
46 *snr = nvbios_rd08(bios, boost + 4); in nvbios_boostTe()
47 *ssz = nvbios_rd08(bios, boost + 3); in nvbios_boostTe()
48 return boost; in nvbios_boostTe()
/Linux-v4.19/Documentation/devicetree/bindings/power/supply/
Dbq25890.txt16 - ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
17 - ti,boost-max-current: integer, maximum allowed current draw in boost mode
21 - ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
41 ti,boost-voltage = <5000000>;
42 ti,boost-max-current = <1000000>;
Drt9455_charger.txt16 - richtek,boost-output-voltage: integer, maximum voltage provided to consumer
17 devices, when the charger is in boost mode, in uV.
42 richtek,boost-output-voltage = <5050000>;
/Linux-v4.19/Documentation/devicetree/bindings/sound/
Dcs35l34.txt13 - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
17 - cirrus,boost-nanohenry: Inductor value for boost converter. The value is
28 - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The
59 cirrus,boost-vtge-milltvolt = <8000>; /* 8V */
60 cirrus,boost-ind-nanohenry = <1000>; /* 1uH */
61 cirrus,boost-peak-milliamp = <3000>; /* 3A */
Dcs35l35.txt17 - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
37 - cirrus,external-boost : Boolean to specify the device is using an external
38 boost supply, note that sharing a boost from another cs35l35 would constitute
55 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
60 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
61 Configures the peak current by monitoring the current through the boost FET.
150 cirrus,boost-ctl-millivolt = <9000>;
155 cirrus,shared-boost;
Dcs35l33.txt21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
22 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
34 - cirrus,boost-ipk : The maximum current allowed for the boost converter.
109 cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */
110 cirrus,boost-ipk = <0xE0>; /* 3600mA */
Dcs35l32.txt18 - cirrus,boost-manager : Boost voltage control.
59 cirrus,boost-manager = <0x03>;
/Linux-v4.19/Documentation/devicetree/bindings/mfd/
Dmax77693.txt89 - maxim,boost-mode :
90 In boost mode the device can produce up to 1.2A of total current
92 to 625mA then. If not enabled explicitly, boost setting defaults to
95 LEDS_BOOST_OFF (0) - no boost,
98 - maxim,boost-mvout : Output voltage of the boost module in millivolts.
117 (boost mode must be turned off):
181 maxim,boost-mode = <LEDS_BOOST_FIXED>;
182 maxim,boost-mvout = <5000>;
/Linux-v4.19/Documentation/devicetree/bindings/leds/backlight/
Dpm8941-wled.txt16 - qcom,current-boost-limit: mA; boost current limit; one of:
38 qcom,current-boost-limit = <805>;
Dtps65217-backlight.txt3 The TPS65217 chip contains a boost converter and current sinks which can be
/Linux-v4.19/Documentation/usb/
Diuu_phoenix.txt37 parm: boost:overclock boost percent 100 to 500 (int)
48 - boost provide a way to overclock the reader ( my favorite :-) )
51 modprobe boost=195
74 use this settings to deduce de boost but is that feature
/Linux-v4.19/drivers/usb/serial/
Diuu_phoenix.c38 static int boost = 100; variable
61 u32 boost; member
914 baud * priv->boost / 100, in iuu_set_termios()
987 if (boost < 100) in iuu_open()
988 boost = 100; in iuu_open()
989 priv->boost = boost; in iuu_open()
993 iuu_clk(port, IUU_CLK_3680000 * boost / 100); in iuu_open()
995 iuu_uart_baud(port, baud * boost / 100, &actual, in iuu_open()
999 iuu_clk(port, IUU_CLK_6000000 * boost / 100); in iuu_open()
1003 iuu_uart_baud(port, 16457 * boost / 100, &actual, in iuu_open()
[all …]
/Linux-v4.19/Documentation/devicetree/bindings/ata/
Dimx-sata.txt19 - fsl,transmit-boost-mdB : transmit boost level, in milli-decibels
/Linux-v4.19/sound/pcmcia/vx/
Dvxpocket.h50 void vx_set_mic_boost(struct vx_core *chip, int boost);
/Linux-v4.19/tools/power/cpupower/
DToDo5 - Try to read out boost states and frequencies on Intel
/Linux-v4.19/Documentation/ABI/testing/
Dsysfs-bus-iio-distance-srf086 Show or set the gain boost of the amp, from 0-31 range.
Dsysfs-bus-iio-proximity-as393514 Show or set the gain boost of the amp, from 0-31 range.
/Linux-v4.19/Documentation/devicetree/bindings/phy/
Dapm-xgene-phy.txt27 - apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit)
/Linux-v4.19/Documentation/admin-guide/pm/
Dcpufreq.rst606 term "frequency boost" is used here for brevity to refer to all of those
609 The frequency boost mechanism may be either hardware-based or software-based.
616 The ``boost`` File in ``sysfs``
620 the "boost" setting for the whole system. It is not present if the underlying
621 scaling driver does not support the frequency boost mechanism (or supports it,
625 If the value in this file is 1, the frequency boost mechanism is enabled. This
630 permission to use the frequency boost mechanism (which still may never be used
633 If the value in this file is 0, the frequency boost mechanism is disabled and
641 The frequency boost mechanism is generally intended to help to achieve optimum
646 For this reason, many systems make it possible to disable the frequency boost
[all …]
/Linux-v4.19/Documentation/devicetree/bindings/leds/
Dleds-lp8860.txt4 driver with boost controller. It has 4 high-precision
/Linux-v4.19/drivers/power/supply/
Dbq2415x_charger.c735 int boost = 0; in bq2415x_set_mode() local
738 boost = 1; in bq2415x_set_mode()
745 if (!boost) in bq2415x_set_mode()
779 else if (boost) in bq2415x_set_mode()
900 int boost; in bq2415x_timer_work() local
916 boost = bq2415x_exec_command(bq, BQ2415X_BOOST_MODE_STATUS); in bq2415x_timer_work()
917 if (boost < 0) { in bq2415x_timer_work()
928 if (boost) { in bq2415x_timer_work()
/Linux-v4.19/arch/arm64/boot/dts/exynos/
Dexynos7-espresso.dts45 usb3drd_boost_5v: regulator-usb3drd-boost {
396 usb3drd_boost_en: usb3drd-boost-en {
406 vbus-boost-supply = <&usb3drd_boost_5v>;
/Linux-v4.19/arch/arm64/boot/dts/nvidia/
Dtegra210-p2371-2180.dts74 /* boost frequency 1 MHz */
/Linux-v4.19/drivers/gpu/drm/i915/
Di915_sysfs.c307 bool boost = false; in gt_boost_freq_mhz_store() local
323 boost = atomic_read(&rps->num_waiters); in gt_boost_freq_mhz_store()
326 if (boost) in gt_boost_freq_mhz_store()
/Linux-v4.19/Documentation/hwmon/
Dlm93244 For each temperature channel, there is a boost temperature: if the channel
247 There is also a hysteresis temperature for this function: after the boost
249 the boost function is disabled. This temperature is also expressed in degrees
304 temp<n>_auto_boost temperature channel boost (PWMs to 100%) limit
306 temp<n>_auto_boost_hyst temperature channel boost hysteresis

1234