Searched refs:blinking (Results 1 – 22 of 22) sorted by relevance
| /Linux-v4.19/Documentation/admin-guide/ |
| D | vga-softcursor.rst | 9 tricks: you can make your cursor look like a non-blinking red block,
40 on highlight (or sometimes blinking -- it depends on the configuration
52 To get normal blinking underline, use::
56 To get blinking block, use::
60 To get red non-blinking block, use::
|
| /Linux-v4.19/drivers/leds/ |
| D | leds-gpio.c | 28 u8 blinking; member
49 if (led_dat->blinking) { in gpio_led_set()
52 led_dat->blinking = 0; in gpio_led_set()
73 led_dat->blinking = 1; in gpio_blink_set()
120 led_dat->blinking = 0; in create_gpio_led()
|
| D | leds-ss4200.c | 460 int blinking = 0; in nas_led_blink_show() local
462 blinking = 1; in nas_led_blink_show()
463 return sprintf(buf, "%u\n", blinking); in nas_led_blink_show()
|
| D | leds-lm355x.c | 122 u8 blinking; member
372 indicator_pattern[state].blinking); in lm3556_indicator_pattern_store()
|
| D | Kconfig | 141 hardware-accelerated blinking with maximum on and off periods of 9.8
520 can stop the front LED from blinking after startup.
582 cannot be used. This driver supports hardware blinking with an on+off
591 Driver support brightness control and hardware-assisted blinking.
|
| /Linux-v4.19/Documentation/leds/ |
| D | leds-class.txt | 61 blinking,
65 blinking, returns -EBUSY if software blink fallback is enabled.
88 blink_set() function (see <linux/leds.h>). To set an LED to blinking,
92 To turn off blinking, use the API function led_brightness_set()
94 timers that may have been required for blinking.
96 The blink_set() function should choose a user friendly blinking value
103 hardware blinking function, if any.
|
| D | ledtrig-oneshot.txt | 12 event, while in the latter it keeps blinking at constant rate, as to signal
39 echo 1 > shot # led starts blinking, ignored if already blinking
|
| D | leds-lp55xx.txt | 80 For example, run blinking pattern in engine #1 of LP5521
87 For example, run blinking pattern in engine #3 of LP55231
96 To start blinking patterns in engine #2 and #3 simultaneously,
163 /* mode_1: blinking data */
190 echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
|
| D | leds-lp5562.txt | 40 For example, run blinking green channel pattern,
48 To run a blinking white pattern,
|
| D | leds-blinkm.txt | 9 Also you can store blinking sequences as "scripts" in
|
| D | leds-mlxcpld.txt | 109 Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
|
| /Linux-v4.19/Documentation/devicetree/bindings/leds/ |
| D | pca963x.txt | 9 - nxp,hw-blink : use hardware blinking instead of software blinking
|
| D | leds-ns2.txt | 11 - modes-map: A mapping between LED modes (off, on or SATA activity blinking) and
|
| D | common.txt | 5 blinking patterns, flash timeout, flash faults and external flash strobe mode.
|
| /Linux-v4.19/drivers/leds/trigger/ |
| D | Kconfig | 16 blinking the LED without any further software interaction.
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | armada-xp-lenovo-ix4-300d.dts | 198 /* init blinking while booting */
|
| /Linux-v4.19/Documentation/media/kapi/ |
| D | rc-core.rst | 29 The infrared transmission is done by blinking a infrared emitter using a
|
| /Linux-v4.19/Documentation/driver-api/80211/ |
| D | mac80211-advanced.rst | 12 Mac80211 supports various ways of blinking LEDs. Wherever possible,
|
| /Linux-v4.19/Documentation/fb/ |
| D | matroxfb.txt | 194 noblink - disables cursor blinking. Cursor in text mode always blinks (hw
196 blink - enables cursor blinking. It is default.
|
| /Linux-v4.19/drivers/atm/ |
| D | iphase.c | 2437 static u_char blinking[8] = {0, 0, 0, 0, 0, 0, 0, 0}; local
2443 if (blinking[i] == 0) {
2444 blinking[i]++;
2450 blinking[i] = 0;
|
| /Linux-v4.19/arch/sparc/ |
| D | Kconfig | 384 by reading /proc/led and its blinking mode can be changed
|
| /Linux-v4.19/Documentation/networking/ |
| D | arcnet-hardware.txt | 1199 blinking. I don't know what 0x3D0 is for though. I recommend using
|
