Home
last modified time | relevance | path

Searched refs:DIP (Results 1 – 13 of 13) sorted by relevance

/Linux-v4.19/Documentation/serial/
Drocket.txt26 The RocketPort ISA board requires I/O ports to be configured by the DIP
28 information on how to set the DIP switches.
88 card before installing and using it. This is done by setting a set of DIP
99 0x300h, 0x340h, 0x380h. This I/O address must be reflected in the DIP
107 software control. The DIP switch settings for the I/O address must be
112 Rocketport board must be set with the DIP switches corresponding to
113 the first board, the second board must be set with the DIP switches
115 the only place where the DIP switch settings should differ between the
143 DIP Switches DIP Switches
151 DIP Switches I/O Address Range
/Linux-v4.19/arch/sh/boards/
DKconfig218 DIP switch(S2-5). If you set the DIP switch for S2-5 = ON,
/Linux-v4.19/arch/x86/kvm/
Demulate.c4333 #define DIP(_y, _i, _p) { .flags = (_y)|Intercept|CheckPerm, \ macro
4352 #define D2bvIP(_f, _i, _p) DIP((_f) | ByteOp, _i, _p), DIP(_f, _i, _p)
4375 DIP(SrcNone | Prot | Priv, vmrun, check_svme_pa),
4377 DIP(SrcNone | Prot | Priv, vmload, check_svme_pa),
4378 DIP(SrcNone | Prot | Priv, vmsave, check_svme_pa),
4379 DIP(SrcNone | Prot | Priv, stgi, check_svme),
4380 DIP(SrcNone | Prot | Priv, clgi, check_svme),
4381 DIP(SrcNone | Prot | Priv, skinit, check_svme),
4382 DIP(SrcNone | Prot | Priv, invlpga, check_svme),
4387 DIP(SrcNone, rdtscp, check_rdtsc),
[all …]
/Linux-v4.19/arch/arm/boot/dts/
Dam3517-evm.dts209 /* User DIP swithes [1:8] / User LEDS [1:2] */
Ddra72-evm-common.dtsi296 /* To use NAND, DIP switch SW5 must be set like so:
/Linux-v4.19/drivers/scsi/sym53c8xx_2/
Dsym_defs.h185 #define DIP 0x01 /* sta: host/script interrupt */ macro
Dsym_hipd.c166 else if (istat & DIP) { in sym_soft_reset()
1038 if (INB(np, nc_istat) & (INTF|SIP|DIP))
2840 if (!(istat & (SIP|DIP)))
2864 if (istatc & DIP)
2875 } while (istatc & (SIP|DIP));
/Linux-v4.19/Documentation/networking/
Darcnet-hardware.txt1032 SW1: DIP-Switches for Station Address
1033 SW2: DIP-Switches for Memory Base and I/O Base addresses
1052 (DIP-Switch downwards means "0")
1056 The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
1070 DIP Switches 1-5 of SW2 encode the RAM and ROM Address Range:
1169 DIP Switches:
1171 The DIP switches accessible on the accessible end of the card while
1186 There is another array of eight DIP switches at the top of the
1192 are in a weird order. This was tested by setting the DIP switches,
2253 There is a DIP-switch with 8 switches, used to set the shared memory address
D6pack.txt67 is supplied with a DIP switch so you can easily change between the
Darcnet.txt151 default which is still set in DIP switches on the card. If you don't have the
/Linux-v4.19/drivers/scsi/
Dncr53c8xx.h705 #define DIP 0x01 /* sta: host/script interrupt */ macro
Dncr53c8xx.c5781 if (INB(nc_istat) & (INTF|SIP|DIP)) { in ncr_timeout()
5924 if (!(istat & (SIP|DIP))) in ncr_exception()
5936 dstat = (istat & DIP) ? INB (nc_dstat) : 0; in ncr_exception()
7740 if (INB(nc_istat) & (INTF|SIP|DIP))
/Linux-v4.19/drivers/gpio/
DKconfig925 includes reads of pushbuttons and DIP switches as well