Searched refs:CS1 (Results 1 – 25 of 46) sorted by relevance
12
| /Linux-v4.19/drivers/staging/fbtft/ |
| D | fb_agm1264k-fl.c | 33 #define CS1 gpio.aux[1] macro
119 if (par->CS1 < 0) { in verify_gpios()
149 par->CS1 = gpio->gpio; in request_gpios_match()
198 gpio_set_value(par->CS1, 0); in write_reg8_bus8()
202 gpio_set_value(par->CS1, 1); in write_reg8_bus8()
401 gpio_set_value(par->CS1, 1); in write_vmem()
|
| /Linux-v4.19/Documentation/devicetree/bindings/memory-controllers/ti/ |
| D | emif.txt | 39 - cs1-used : Have this property if CS1 of this EMIF
41 part attached to CS1, it should be the same type as the one on CS0,
|
| /Linux-v4.19/Documentation/devicetree/bindings/mtd/ |
| D | tango-nand.txt | 34 reg = <1>; /* CS1 */
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | armada-370-xp.dtsi | 273 <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */
291 <MBUS_ID(0x01, 0x5a) 0 0xffffffff>, /* CS1 */
|
| D | armada-388-clearfog.dts | 234 * CS1:
|
| D | imx6dl-riotboard.dts | 396 MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x000b1 /* CS1 */
410 MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x000b1 /* CS1 */
|
| D | imx6qdl-ts4900.dtsi | 166 MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x100b1 /* Onboard flash CS1# */
176 MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x100b1 /* FPGA CS1# */
|
| D | omap3-overo-common-lcd35.dtsi | 126 reg = <1>; /* CS1 */
|
| D | armada-388-clearfog.dtsi | 229 * CS1: PIC microcontroller (Pro models)
|
| D | omap3430-sdp.dts | 54 <1 0 0x28000000 0x1000000>, /* CS1: 16MB for NAND */
|
| D | armada-385-turris-omnia.dts | 344 /* MISO, MOSI, SCLK and CS1 are routed to pin header CN11 */
|
| D | imx6dl-colibri-eval-v3.dts | 230 /* weim memory map: 32MB on CS0, 32MB on CS1, 32MB on CS2 */
|
| D | logicpd-som-lv-baseboard.dtsi | 67 1 0 0x2c000000 0x1000000 /* CS1: 16MB for LAN9221 */
|
| D | omap3-ldp.dts | 101 <1 0 0x08000000 0x1000000>; /* CS1 space, 16MB */
|
| D | imx6qdl-var-dart.dtsi | 223 /* SPI1 CS1 */
|
| /Linux-v4.19/arch/powerpc/boot/dts/ |
| D | motionpro.dts | 98 // 8-bit DualPort SRAM on LocalPlus Bus CS1
|
| D | charon.dts | 189 1 0 0xe0000000 0x04000000 // CS1 range, SM501
|
| D | mpc8308rdb.dts | 58 // CS0 and CS1 are swapped when
|
| D | ac14xx.dts | 46 0x1 0x0 0xe0000000 0x00010000 /* CS1: FRAM */
|
| /Linux-v4.19/Documentation/devicetree/bindings/memory-controllers/ |
| D | ingenic,jz4780-nemc.txt | 45 Example (NEMC node with a NAND child device attached at CS1):
|
| /Linux-v4.19/Documentation/devicetree/bindings/bus/ |
| D | qcom,ebi2.txt | 18 Also CS1 and CS2 has -A and -B signals. Why they have that is unclear to me.
25 CS1 GPIO39 (A) / GPIO123 (B) 0x1b000000-0x1b800000 (8MB)
|
| D | uniphier-system-bus.txt | 63 - the Ethernet device is connected at the offset 0x01f00000 of CS1 and
|
| D | imx-weim.txt | 36 IOMUXC_GPR1[11:0] CS0 CS1 CS2 CS3
|
| /Linux-v4.19/Documentation/devicetree/bindings/spi/ |
| D | spi-orion.txt | 51 <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */
|
| /Linux-v4.19/drivers/media/dvb-frontends/ |
| D | bcm3510_priv.h | 150 u8 CS1 :1; member
|
12
