1 /* SPDX-License-Identifier: ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) */
2 /*
3 * cec - HDMI Consumer Electronics Control public header
4 *
5 * Copyright 2016 Cisco Systems, Inc. and/or its affiliates. All rights reserved.
6 */
7
8 #ifndef _CEC_UAPI_H
9 #define _CEC_UAPI_H
10
11 #include <linux/types.h>
12 #include <linux/string.h>
13
14 #define CEC_MAX_MSG_SIZE 16
15
16 /**
17 * struct cec_msg - CEC message structure.
18 * @tx_ts: Timestamp in nanoseconds using CLOCK_MONOTONIC. Set by the
19 * driver when the message transmission has finished.
20 * @rx_ts: Timestamp in nanoseconds using CLOCK_MONOTONIC. Set by the
21 * driver when the message was received.
22 * @len: Length in bytes of the message.
23 * @timeout: The timeout (in ms) that is used to timeout CEC_RECEIVE.
24 * Set to 0 if you want to wait forever. This timeout can also be
25 * used with CEC_TRANSMIT as the timeout for waiting for a reply.
26 * If 0, then it will use a 1 second timeout instead of waiting
27 * forever as is done with CEC_RECEIVE.
28 * @sequence: The framework assigns a sequence number to messages that are
29 * sent. This can be used to track replies to previously sent
30 * messages.
31 * @flags: Set to 0.
32 * @msg: The message payload.
33 * @reply: This field is ignored with CEC_RECEIVE and is only used by
34 * CEC_TRANSMIT. If non-zero, then wait for a reply with this
35 * opcode. Set to CEC_MSG_FEATURE_ABORT if you want to wait for
36 * a possible ABORT reply. If there was an error when sending the
37 * msg or FeatureAbort was returned, then reply is set to 0.
38 * If reply is non-zero upon return, then len/msg are set to
39 * the received message.
40 * If reply is zero upon return and status has the
41 * CEC_TX_STATUS_FEATURE_ABORT bit set, then len/msg are set to
42 * the received feature abort message.
43 * If reply is zero upon return and status has the
44 * CEC_TX_STATUS_MAX_RETRIES bit set, then no reply was seen at
45 * all. If reply is non-zero for CEC_TRANSMIT and the message is a
46 * broadcast, then -EINVAL is returned.
47 * if reply is non-zero, then timeout is set to 1000 (the required
48 * maximum response time).
49 * @rx_status: The message receive status bits. Set by the driver.
50 * @tx_status: The message transmit status bits. Set by the driver.
51 * @tx_arb_lost_cnt: The number of 'Arbitration Lost' events. Set by the driver.
52 * @tx_nack_cnt: The number of 'Not Acknowledged' events. Set by the driver.
53 * @tx_low_drive_cnt: The number of 'Low Drive Detected' events. Set by the
54 * driver.
55 * @tx_error_cnt: The number of 'Error' events. Set by the driver.
56 */
57 struct cec_msg {
58 __u64 tx_ts;
59 __u64 rx_ts;
60 __u32 len;
61 __u32 timeout;
62 __u32 sequence;
63 __u32 flags;
64 __u8 msg[CEC_MAX_MSG_SIZE];
65 __u8 reply;
66 __u8 rx_status;
67 __u8 tx_status;
68 __u8 tx_arb_lost_cnt;
69 __u8 tx_nack_cnt;
70 __u8 tx_low_drive_cnt;
71 __u8 tx_error_cnt;
72 };
73
74 /**
75 * cec_msg_initiator - return the initiator's logical address.
76 * @msg: the message structure
77 */
cec_msg_initiator(const struct cec_msg * msg)78 static inline __u8 cec_msg_initiator(const struct cec_msg *msg)
79 {
80 return msg->msg[0] >> 4;
81 }
82
83 /**
84 * cec_msg_destination - return the destination's logical address.
85 * @msg: the message structure
86 */
cec_msg_destination(const struct cec_msg * msg)87 static inline __u8 cec_msg_destination(const struct cec_msg *msg)
88 {
89 return msg->msg[0] & 0xf;
90 }
91
92 /**
93 * cec_msg_opcode - return the opcode of the message, -1 for poll
94 * @msg: the message structure
95 */
cec_msg_opcode(const struct cec_msg * msg)96 static inline int cec_msg_opcode(const struct cec_msg *msg)
97 {
98 return msg->len > 1 ? msg->msg[1] : -1;
99 }
100
101 /**
102 * cec_msg_is_broadcast - return true if this is a broadcast message.
103 * @msg: the message structure
104 */
cec_msg_is_broadcast(const struct cec_msg * msg)105 static inline int cec_msg_is_broadcast(const struct cec_msg *msg)
106 {
107 return (msg->msg[0] & 0xf) == 0xf;
108 }
109
110 /**
111 * cec_msg_init - initialize the message structure.
112 * @msg: the message structure
113 * @initiator: the logical address of the initiator
114 * @destination:the logical address of the destination (0xf for broadcast)
115 *
116 * The whole structure is zeroed, the len field is set to 1 (i.e. a poll
117 * message) and the initiator and destination are filled in.
118 */
cec_msg_init(struct cec_msg * msg,__u8 initiator,__u8 destination)119 static inline void cec_msg_init(struct cec_msg *msg,
120 __u8 initiator, __u8 destination)
121 {
122 memset(msg, 0, sizeof(*msg));
123 msg->msg[0] = (initiator << 4) | destination;
124 msg->len = 1;
125 }
126
127 /**
128 * cec_msg_set_reply_to - fill in destination/initiator in a reply message.
129 * @msg: the message structure for the reply
130 * @orig: the original message structure
131 *
132 * Set the msg destination to the orig initiator and the msg initiator to the
133 * orig destination. Note that msg and orig may be the same pointer, in which
134 * case the change is done in place.
135 */
cec_msg_set_reply_to(struct cec_msg * msg,struct cec_msg * orig)136 static inline void cec_msg_set_reply_to(struct cec_msg *msg,
137 struct cec_msg *orig)
138 {
139 /* The destination becomes the initiator and vice versa */
140 msg->msg[0] = (cec_msg_destination(orig) << 4) |
141 cec_msg_initiator(orig);
142 msg->reply = msg->timeout = 0;
143 }
144
145 /* cec_msg flags field */
146 #define CEC_MSG_FL_REPLY_TO_FOLLOWERS (1 << 0)
147
148 /* cec_msg tx/rx_status field */
149 #define CEC_TX_STATUS_OK (1 << 0)
150 #define CEC_TX_STATUS_ARB_LOST (1 << 1)
151 #define CEC_TX_STATUS_NACK (1 << 2)
152 #define CEC_TX_STATUS_LOW_DRIVE (1 << 3)
153 #define CEC_TX_STATUS_ERROR (1 << 4)
154 #define CEC_TX_STATUS_MAX_RETRIES (1 << 5)
155
156 #define CEC_RX_STATUS_OK (1 << 0)
157 #define CEC_RX_STATUS_TIMEOUT (1 << 1)
158 #define CEC_RX_STATUS_FEATURE_ABORT (1 << 2)
159
cec_msg_status_is_ok(const struct cec_msg * msg)160 static inline int cec_msg_status_is_ok(const struct cec_msg *msg)
161 {
162 if (msg->tx_status && !(msg->tx_status & CEC_TX_STATUS_OK))
163 return 0;
164 if (msg->rx_status && !(msg->rx_status & CEC_RX_STATUS_OK))
165 return 0;
166 if (!msg->tx_status && !msg->rx_status)
167 return 0;
168 return !(msg->rx_status & CEC_RX_STATUS_FEATURE_ABORT);
169 }
170
171 #define CEC_LOG_ADDR_INVALID 0xff
172 #define CEC_PHYS_ADDR_INVALID 0xffff
173
174 /*
175 * The maximum number of logical addresses one device can be assigned to.
176 * The CEC 2.0 spec allows for only 2 logical addresses at the moment. The
177 * Analog Devices CEC hardware supports 3. So let's go wild and go for 4.
178 */
179 #define CEC_MAX_LOG_ADDRS 4
180
181 /* The logical addresses defined by CEC 2.0 */
182 #define CEC_LOG_ADDR_TV 0
183 #define CEC_LOG_ADDR_RECORD_1 1
184 #define CEC_LOG_ADDR_RECORD_2 2
185 #define CEC_LOG_ADDR_TUNER_1 3
186 #define CEC_LOG_ADDR_PLAYBACK_1 4
187 #define CEC_LOG_ADDR_AUDIOSYSTEM 5
188 #define CEC_LOG_ADDR_TUNER_2 6
189 #define CEC_LOG_ADDR_TUNER_3 7
190 #define CEC_LOG_ADDR_PLAYBACK_2 8
191 #define CEC_LOG_ADDR_RECORD_3 9
192 #define CEC_LOG_ADDR_TUNER_4 10
193 #define CEC_LOG_ADDR_PLAYBACK_3 11
194 #define CEC_LOG_ADDR_BACKUP_1 12
195 #define CEC_LOG_ADDR_BACKUP_2 13
196 #define CEC_LOG_ADDR_SPECIFIC 14
197 #define CEC_LOG_ADDR_UNREGISTERED 15 /* as initiator address */
198 #define CEC_LOG_ADDR_BROADCAST 15 /* as destination address */
199
200 /* The logical address types that the CEC device wants to claim */
201 #define CEC_LOG_ADDR_TYPE_TV 0
202 #define CEC_LOG_ADDR_TYPE_RECORD 1
203 #define CEC_LOG_ADDR_TYPE_TUNER 2
204 #define CEC_LOG_ADDR_TYPE_PLAYBACK 3
205 #define CEC_LOG_ADDR_TYPE_AUDIOSYSTEM 4
206 #define CEC_LOG_ADDR_TYPE_SPECIFIC 5
207 #define CEC_LOG_ADDR_TYPE_UNREGISTERED 6
208 /*
209 * Switches should use UNREGISTERED.
210 * Processors should use SPECIFIC.
211 */
212
213 #define CEC_LOG_ADDR_MASK_TV (1 << CEC_LOG_ADDR_TV)
214 #define CEC_LOG_ADDR_MASK_RECORD ((1 << CEC_LOG_ADDR_RECORD_1) | \
215 (1 << CEC_LOG_ADDR_RECORD_2) | \
216 (1 << CEC_LOG_ADDR_RECORD_3))
217 #define CEC_LOG_ADDR_MASK_TUNER ((1 << CEC_LOG_ADDR_TUNER_1) | \
218 (1 << CEC_LOG_ADDR_TUNER_2) | \
219 (1 << CEC_LOG_ADDR_TUNER_3) | \
220 (1 << CEC_LOG_ADDR_TUNER_4))
221 #define CEC_LOG_ADDR_MASK_PLAYBACK ((1 << CEC_LOG_ADDR_PLAYBACK_1) | \
222 (1 << CEC_LOG_ADDR_PLAYBACK_2) | \
223 (1 << CEC_LOG_ADDR_PLAYBACK_3))
224 #define CEC_LOG_ADDR_MASK_AUDIOSYSTEM (1 << CEC_LOG_ADDR_AUDIOSYSTEM)
225 #define CEC_LOG_ADDR_MASK_BACKUP ((1 << CEC_LOG_ADDR_BACKUP_1) | \
226 (1 << CEC_LOG_ADDR_BACKUP_2))
227 #define CEC_LOG_ADDR_MASK_SPECIFIC (1 << CEC_LOG_ADDR_SPECIFIC)
228 #define CEC_LOG_ADDR_MASK_UNREGISTERED (1 << CEC_LOG_ADDR_UNREGISTERED)
229
cec_has_tv(__u16 log_addr_mask)230 static inline int cec_has_tv(__u16 log_addr_mask)
231 {
232 return log_addr_mask & CEC_LOG_ADDR_MASK_TV;
233 }
234
cec_has_record(__u16 log_addr_mask)235 static inline int cec_has_record(__u16 log_addr_mask)
236 {
237 return log_addr_mask & CEC_LOG_ADDR_MASK_RECORD;
238 }
239
cec_has_tuner(__u16 log_addr_mask)240 static inline int cec_has_tuner(__u16 log_addr_mask)
241 {
242 return log_addr_mask & CEC_LOG_ADDR_MASK_TUNER;
243 }
244
cec_has_playback(__u16 log_addr_mask)245 static inline int cec_has_playback(__u16 log_addr_mask)
246 {
247 return log_addr_mask & CEC_LOG_ADDR_MASK_PLAYBACK;
248 }
249
cec_has_audiosystem(__u16 log_addr_mask)250 static inline int cec_has_audiosystem(__u16 log_addr_mask)
251 {
252 return log_addr_mask & CEC_LOG_ADDR_MASK_AUDIOSYSTEM;
253 }
254
cec_has_backup(__u16 log_addr_mask)255 static inline int cec_has_backup(__u16 log_addr_mask)
256 {
257 return log_addr_mask & CEC_LOG_ADDR_MASK_BACKUP;
258 }
259
cec_has_specific(__u16 log_addr_mask)260 static inline int cec_has_specific(__u16 log_addr_mask)
261 {
262 return log_addr_mask & CEC_LOG_ADDR_MASK_SPECIFIC;
263 }
264
cec_is_unregistered(__u16 log_addr_mask)265 static inline int cec_is_unregistered(__u16 log_addr_mask)
266 {
267 return log_addr_mask & CEC_LOG_ADDR_MASK_UNREGISTERED;
268 }
269
cec_is_unconfigured(__u16 log_addr_mask)270 static inline int cec_is_unconfigured(__u16 log_addr_mask)
271 {
272 return log_addr_mask == 0;
273 }
274
275 /*
276 * Use this if there is no vendor ID (CEC_G_VENDOR_ID) or if the vendor ID
277 * should be disabled (CEC_S_VENDOR_ID)
278 */
279 #define CEC_VENDOR_ID_NONE 0xffffffff
280
281 /* The message handling modes */
282 /* Modes for initiator */
283 #define CEC_MODE_NO_INITIATOR (0x0 << 0)
284 #define CEC_MODE_INITIATOR (0x1 << 0)
285 #define CEC_MODE_EXCL_INITIATOR (0x2 << 0)
286 #define CEC_MODE_INITIATOR_MSK 0x0f
287
288 /* Modes for follower */
289 #define CEC_MODE_NO_FOLLOWER (0x0 << 4)
290 #define CEC_MODE_FOLLOWER (0x1 << 4)
291 #define CEC_MODE_EXCL_FOLLOWER (0x2 << 4)
292 #define CEC_MODE_EXCL_FOLLOWER_PASSTHRU (0x3 << 4)
293 #define CEC_MODE_MONITOR_PIN (0xd << 4)
294 #define CEC_MODE_MONITOR (0xe << 4)
295 #define CEC_MODE_MONITOR_ALL (0xf << 4)
296 #define CEC_MODE_FOLLOWER_MSK 0xf0
297
298 /* Userspace has to configure the physical address */
299 #define CEC_CAP_PHYS_ADDR (1 << 0)
300 /* Userspace has to configure the logical addresses */
301 #define CEC_CAP_LOG_ADDRS (1 << 1)
302 /* Userspace can transmit messages (and thus become follower as well) */
303 #define CEC_CAP_TRANSMIT (1 << 2)
304 /*
305 * Passthrough all messages instead of processing them.
306 */
307 #define CEC_CAP_PASSTHROUGH (1 << 3)
308 /* Supports remote control */
309 #define CEC_CAP_RC (1 << 4)
310 /* Hardware can monitor all messages, not just directed and broadcast. */
311 #define CEC_CAP_MONITOR_ALL (1 << 5)
312 /* Hardware can use CEC only if the HDMI HPD pin is high. */
313 #define CEC_CAP_NEEDS_HPD (1 << 6)
314 /* Hardware can monitor CEC pin transitions */
315 #define CEC_CAP_MONITOR_PIN (1 << 7)
316
317 /**
318 * struct cec_caps - CEC capabilities structure.
319 * @driver: name of the CEC device driver.
320 * @name: name of the CEC device. @driver + @name must be unique.
321 * @available_log_addrs: number of available logical addresses.
322 * @capabilities: capabilities of the CEC adapter.
323 * @version: version of the CEC adapter framework.
324 */
325 struct cec_caps {
326 char driver[32];
327 char name[32];
328 __u32 available_log_addrs;
329 __u32 capabilities;
330 __u32 version;
331 };
332
333 /**
334 * struct cec_log_addrs - CEC logical addresses structure.
335 * @log_addr: the claimed logical addresses. Set by the driver.
336 * @log_addr_mask: current logical address mask. Set by the driver.
337 * @cec_version: the CEC version that the adapter should implement. Set by the
338 * caller.
339 * @num_log_addrs: how many logical addresses should be claimed. Set by the
340 * caller.
341 * @vendor_id: the vendor ID of the device. Set by the caller.
342 * @flags: flags.
343 * @osd_name: the OSD name of the device. Set by the caller.
344 * @primary_device_type: the primary device type for each logical address.
345 * Set by the caller.
346 * @log_addr_type: the logical address types. Set by the caller.
347 * @all_device_types: CEC 2.0: all device types represented by the logical
348 * address. Set by the caller.
349 * @features: CEC 2.0: The logical address features. Set by the caller.
350 */
351 struct cec_log_addrs {
352 __u8 log_addr[CEC_MAX_LOG_ADDRS];
353 __u16 log_addr_mask;
354 __u8 cec_version;
355 __u8 num_log_addrs;
356 __u32 vendor_id;
357 __u32 flags;
358 char osd_name[15];
359 __u8 primary_device_type[CEC_MAX_LOG_ADDRS];
360 __u8 log_addr_type[CEC_MAX_LOG_ADDRS];
361
362 /* CEC 2.0 */
363 __u8 all_device_types[CEC_MAX_LOG_ADDRS];
364 __u8 features[CEC_MAX_LOG_ADDRS][12];
365 };
366
367 /* Allow a fallback to unregistered */
368 #define CEC_LOG_ADDRS_FL_ALLOW_UNREG_FALLBACK (1 << 0)
369 /* Passthrough RC messages to the input subsystem */
370 #define CEC_LOG_ADDRS_FL_ALLOW_RC_PASSTHRU (1 << 1)
371 /* CDC-Only device: supports only CDC messages */
372 #define CEC_LOG_ADDRS_FL_CDC_ONLY (1 << 2)
373
374 /* Events */
375
376 /* Event that occurs when the adapter state changes */
377 #define CEC_EVENT_STATE_CHANGE 1
378 /*
379 * This event is sent when messages are lost because the application
380 * didn't empty the message queue in time
381 */
382 #define CEC_EVENT_LOST_MSGS 2
383 #define CEC_EVENT_PIN_CEC_LOW 3
384 #define CEC_EVENT_PIN_CEC_HIGH 4
385 #define CEC_EVENT_PIN_HPD_LOW 5
386 #define CEC_EVENT_PIN_HPD_HIGH 6
387 #define CEC_EVENT_PIN_5V_LOW 7
388 #define CEC_EVENT_PIN_5V_HIGH 8
389
390 #define CEC_EVENT_FL_INITIAL_STATE (1 << 0)
391 #define CEC_EVENT_FL_DROPPED_EVENTS (1 << 1)
392
393 /**
394 * struct cec_event_state_change - used when the CEC adapter changes state.
395 * @phys_addr: the current physical address
396 * @log_addr_mask: the current logical address mask
397 */
398 struct cec_event_state_change {
399 __u16 phys_addr;
400 __u16 log_addr_mask;
401 };
402
403 /**
404 * struct cec_event_lost_msgs - tells you how many messages were lost.
405 * @lost_msgs: how many messages were lost.
406 */
407 struct cec_event_lost_msgs {
408 __u32 lost_msgs;
409 };
410
411 /**
412 * struct cec_event - CEC event structure
413 * @ts: the timestamp of when the event was sent.
414 * @event: the event.
415 * array.
416 * @state_change: the event payload for CEC_EVENT_STATE_CHANGE.
417 * @lost_msgs: the event payload for CEC_EVENT_LOST_MSGS.
418 * @raw: array to pad the union.
419 */
420 struct cec_event {
421 __u64 ts;
422 __u32 event;
423 __u32 flags;
424 union {
425 struct cec_event_state_change state_change;
426 struct cec_event_lost_msgs lost_msgs;
427 __u32 raw[16];
428 };
429 };
430
431 /* ioctls */
432
433 /* Adapter capabilities */
434 #define CEC_ADAP_G_CAPS _IOWR('a', 0, struct cec_caps)
435
436 /*
437 * phys_addr is either 0 (if this is the CEC root device)
438 * or a valid physical address obtained from the sink's EDID
439 * as read by this CEC device (if this is a source device)
440 * or a physical address obtained and modified from a sink
441 * EDID and used for a sink CEC device.
442 * If nothing is connected, then phys_addr is 0xffff.
443 * See HDMI 1.4b, section 8.7 (Physical Address).
444 *
445 * The CEC_ADAP_S_PHYS_ADDR ioctl may not be available if that is handled
446 * internally.
447 */
448 #define CEC_ADAP_G_PHYS_ADDR _IOR('a', 1, __u16)
449 #define CEC_ADAP_S_PHYS_ADDR _IOW('a', 2, __u16)
450
451 /*
452 * Configure the CEC adapter. It sets the device type and which
453 * logical types it will try to claim. It will return which
454 * logical addresses it could actually claim.
455 * An error is returned if the adapter is disabled or if there
456 * is no physical address assigned.
457 */
458
459 #define CEC_ADAP_G_LOG_ADDRS _IOR('a', 3, struct cec_log_addrs)
460 #define CEC_ADAP_S_LOG_ADDRS _IOWR('a', 4, struct cec_log_addrs)
461
462 /* Transmit/receive a CEC command */
463 #define CEC_TRANSMIT _IOWR('a', 5, struct cec_msg)
464 #define CEC_RECEIVE _IOWR('a', 6, struct cec_msg)
465
466 /* Dequeue CEC events */
467 #define CEC_DQEVENT _IOWR('a', 7, struct cec_event)
468
469 /*
470 * Get and set the message handling mode for this filehandle.
471 */
472 #define CEC_G_MODE _IOR('a', 8, __u32)
473 #define CEC_S_MODE _IOW('a', 9, __u32)
474
475 /*
476 * The remainder of this header defines all CEC messages and operands.
477 * The format matters since it the cec-ctl utility parses it to generate
478 * code for implementing all these messages.
479 *
480 * Comments ending with 'Feature' group messages for each feature.
481 * If messages are part of multiple features, then the "Has also"
482 * comment is used to list the previously defined messages that are
483 * supported by the feature.
484 *
485 * Before operands are defined a comment is added that gives the
486 * name of the operand and in brackets the variable name of the
487 * corresponding argument in the cec-funcs.h function.
488 */
489
490 /* Messages */
491
492 /* One Touch Play Feature */
493 #define CEC_MSG_ACTIVE_SOURCE 0x82
494 #define CEC_MSG_IMAGE_VIEW_ON 0x04
495 #define CEC_MSG_TEXT_VIEW_ON 0x0d
496
497
498 /* Routing Control Feature */
499
500 /*
501 * Has also:
502 * CEC_MSG_ACTIVE_SOURCE
503 */
504
505 #define CEC_MSG_INACTIVE_SOURCE 0x9d
506 #define CEC_MSG_REQUEST_ACTIVE_SOURCE 0x85
507 #define CEC_MSG_ROUTING_CHANGE 0x80
508 #define CEC_MSG_ROUTING_INFORMATION 0x81
509 #define CEC_MSG_SET_STREAM_PATH 0x86
510
511
512 /* Standby Feature */
513 #define CEC_MSG_STANDBY 0x36
514
515
516 /* One Touch Record Feature */
517 #define CEC_MSG_RECORD_OFF 0x0b
518 #define CEC_MSG_RECORD_ON 0x09
519 /* Record Source Type Operand (rec_src_type) */
520 #define CEC_OP_RECORD_SRC_OWN 1
521 #define CEC_OP_RECORD_SRC_DIGITAL 2
522 #define CEC_OP_RECORD_SRC_ANALOG 3
523 #define CEC_OP_RECORD_SRC_EXT_PLUG 4
524 #define CEC_OP_RECORD_SRC_EXT_PHYS_ADDR 5
525 /* Service Identification Method Operand (service_id_method) */
526 #define CEC_OP_SERVICE_ID_METHOD_BY_DIG_ID 0
527 #define CEC_OP_SERVICE_ID_METHOD_BY_CHANNEL 1
528 /* Digital Service Broadcast System Operand (dig_bcast_system) */
529 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ARIB_GEN 0x00
530 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ATSC_GEN 0x01
531 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_DVB_GEN 0x02
532 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ARIB_BS 0x08
533 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ARIB_CS 0x09
534 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ARIB_T 0x0a
535 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ATSC_CABLE 0x10
536 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ATSC_SAT 0x11
537 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_ATSC_T 0x12
538 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_DVB_C 0x18
539 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_DVB_S 0x19
540 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_DVB_S2 0x1a
541 #define CEC_OP_DIG_SERVICE_BCAST_SYSTEM_DVB_T 0x1b
542 /* Analogue Broadcast Type Operand (ana_bcast_type) */
543 #define CEC_OP_ANA_BCAST_TYPE_CABLE 0
544 #define CEC_OP_ANA_BCAST_TYPE_SATELLITE 1
545 #define CEC_OP_ANA_BCAST_TYPE_TERRESTRIAL 2
546 /* Broadcast System Operand (bcast_system) */
547 #define CEC_OP_BCAST_SYSTEM_PAL_BG 0x00
548 #define CEC_OP_BCAST_SYSTEM_SECAM_LQ 0x01 /* SECAM L' */
549 #define CEC_OP_BCAST_SYSTEM_PAL_M 0x02
550 #define CEC_OP_BCAST_SYSTEM_NTSC_M 0x03
551 #define CEC_OP_BCAST_SYSTEM_PAL_I 0x04
552 #define CEC_OP_BCAST_SYSTEM_SECAM_DK 0x05
553 #define CEC_OP_BCAST_SYSTEM_SECAM_BG 0x06
554 #define CEC_OP_BCAST_SYSTEM_SECAM_L 0x07
555 #define CEC_OP_BCAST_SYSTEM_PAL_DK 0x08
556 #define CEC_OP_BCAST_SYSTEM_OTHER 0x1f
557 /* Channel Number Format Operand (channel_number_fmt) */
558 #define CEC_OP_CHANNEL_NUMBER_FMT_1_PART 0x01
559 #define CEC_OP_CHANNEL_NUMBER_FMT_2_PART 0x02
560
561 #define CEC_MSG_RECORD_STATUS 0x0a
562 /* Record Status Operand (rec_status) */
563 #define CEC_OP_RECORD_STATUS_CUR_SRC 0x01
564 #define CEC_OP_RECORD_STATUS_DIG_SERVICE 0x02
565 #define CEC_OP_RECORD_STATUS_ANA_SERVICE 0x03
566 #define CEC_OP_RECORD_STATUS_EXT_INPUT 0x04
567 #define CEC_OP_RECORD_STATUS_NO_DIG_SERVICE 0x05
568 #define CEC_OP_RECORD_STATUS_NO_ANA_SERVICE 0x06
569 #define CEC_OP_RECORD_STATUS_NO_SERVICE 0x07
570 #define CEC_OP_RECORD_STATUS_INVALID_EXT_PLUG 0x09
571 #define CEC_OP_RECORD_STATUS_INVALID_EXT_PHYS_ADDR 0x0a
572 #define CEC_OP_RECORD_STATUS_UNSUP_CA 0x0b
573 #define CEC_OP_RECORD_STATUS_NO_CA_ENTITLEMENTS 0x0c
574 #define CEC_OP_RECORD_STATUS_CANT_COPY_SRC 0x0d
575 #define CEC_OP_RECORD_STATUS_NO_MORE_COPIES 0x0e
576 #define CEC_OP_RECORD_STATUS_NO_MEDIA 0x10
577 #define CEC_OP_RECORD_STATUS_PLAYING 0x11
578 #define CEC_OP_RECORD_STATUS_ALREADY_RECORDING 0x12
579 #define CEC_OP_RECORD_STATUS_MEDIA_PROT 0x13
580 #define CEC_OP_RECORD_STATUS_NO_SIGNAL 0x14
581 #define CEC_OP_RECORD_STATUS_MEDIA_PROBLEM 0x15
582 #define CEC_OP_RECORD_STATUS_NO_SPACE 0x16
583 #define CEC_OP_RECORD_STATUS_PARENTAL_LOCK 0x17
584 #define CEC_OP_RECORD_STATUS_TERMINATED_OK 0x1a
585 #define CEC_OP_RECORD_STATUS_ALREADY_TERM 0x1b
586 #define CEC_OP_RECORD_STATUS_OTHER 0x1f
587
588 #define CEC_MSG_RECORD_TV_SCREEN 0x0f
589
590
591 /* Timer Programming Feature */
592 #define CEC_MSG_CLEAR_ANALOGUE_TIMER 0x33
593 /* Recording Sequence Operand (recording_seq) */
594 #define CEC_OP_REC_SEQ_SUNDAY 0x01
595 #define CEC_OP_REC_SEQ_MONDAY 0x02
596 #define CEC_OP_REC_SEQ_TUESDAY 0x04
597 #define CEC_OP_REC_SEQ_WEDNESDAY 0x08
598 #define CEC_OP_REC_SEQ_THURSDAY 0x10
599 #define CEC_OP_REC_SEQ_FRIDAY 0x20
600 #define CEC_OP_REC_SEQ_SATERDAY 0x40
601 #define CEC_OP_REC_SEQ_ONCE_ONLY 0x00
602
603 #define CEC_MSG_CLEAR_DIGITAL_TIMER 0x99
604
605 #define CEC_MSG_CLEAR_EXT_TIMER 0xa1
606 /* External Source Specifier Operand (ext_src_spec) */
607 #define CEC_OP_EXT_SRC_PLUG 0x04
608 #define CEC_OP_EXT_SRC_PHYS_ADDR 0x05
609
610 #define CEC_MSG_SET_ANALOGUE_TIMER 0x34
611 #define CEC_MSG_SET_DIGITAL_TIMER 0x97
612 #define CEC_MSG_SET_EXT_TIMER 0xa2
613
614 #define CEC_MSG_SET_TIMER_PROGRAM_TITLE 0x67
615 #define CEC_MSG_TIMER_CLEARED_STATUS 0x43
616 /* Timer Cleared Status Data Operand (timer_cleared_status) */
617 #define CEC_OP_TIMER_CLR_STAT_RECORDING 0x00
618 #define CEC_OP_TIMER_CLR_STAT_NO_MATCHING 0x01
619 #define CEC_OP_TIMER_CLR_STAT_NO_INFO 0x02
620 #define CEC_OP_TIMER_CLR_STAT_CLEARED 0x80
621
622 #define CEC_MSG_TIMER_STATUS 0x35
623 /* Timer Overlap Warning Operand (timer_overlap_warning) */
624 #define CEC_OP_TIMER_OVERLAP_WARNING_NO_OVERLAP 0
625 #define CEC_OP_TIMER_OVERLAP_WARNING_OVERLAP 1
626 /* Media Info Operand (media_info) */
627 #define CEC_OP_MEDIA_INFO_UNPROT_MEDIA 0
628 #define CEC_OP_MEDIA_INFO_PROT_MEDIA 1
629 #define CEC_OP_MEDIA_INFO_NO_MEDIA 2
630 /* Programmed Indicator Operand (prog_indicator) */
631 #define CEC_OP_PROG_IND_NOT_PROGRAMMED 0
632 #define CEC_OP_PROG_IND_PROGRAMMED 1
633 /* Programmed Info Operand (prog_info) */
634 #define CEC_OP_PROG_INFO_ENOUGH_SPACE 0x08
635 #define CEC_OP_PROG_INFO_NOT_ENOUGH_SPACE 0x09
636 #define CEC_OP_PROG_INFO_MIGHT_NOT_BE_ENOUGH_SPACE 0x0b
637 #define CEC_OP_PROG_INFO_NONE_AVAILABLE 0x0a
638 /* Not Programmed Error Info Operand (prog_error) */
639 #define CEC_OP_PROG_ERROR_NO_FREE_TIMER 0x01
640 #define CEC_OP_PROG_ERROR_DATE_OUT_OF_RANGE 0x02
641 #define CEC_OP_PROG_ERROR_REC_SEQ_ERROR 0x03
642 #define CEC_OP_PROG_ERROR_INV_EXT_PLUG 0x04
643 #define CEC_OP_PROG_ERROR_INV_EXT_PHYS_ADDR 0x05
644 #define CEC_OP_PROG_ERROR_CA_UNSUPP 0x06
645 #define CEC_OP_PROG_ERROR_INSUF_CA_ENTITLEMENTS 0x07
646 #define CEC_OP_PROG_ERROR_RESOLUTION_UNSUPP 0x08
647 #define CEC_OP_PROG_ERROR_PARENTAL_LOCK 0x09
648 #define CEC_OP_PROG_ERROR_CLOCK_FAILURE 0x0a
649 #define CEC_OP_PROG_ERROR_DUPLICATE 0x0e
650
651
652 /* System Information Feature */
653 #define CEC_MSG_CEC_VERSION 0x9e
654 /* CEC Version Operand (cec_version) */
655 #define CEC_OP_CEC_VERSION_1_3A 4
656 #define CEC_OP_CEC_VERSION_1_4 5
657 #define CEC_OP_CEC_VERSION_2_0 6
658
659 #define CEC_MSG_GET_CEC_VERSION 0x9f
660 #define CEC_MSG_GIVE_PHYSICAL_ADDR 0x83
661 #define CEC_MSG_GET_MENU_LANGUAGE 0x91
662 #define CEC_MSG_REPORT_PHYSICAL_ADDR 0x84
663 /* Primary Device Type Operand (prim_devtype) */
664 #define CEC_OP_PRIM_DEVTYPE_TV 0
665 #define CEC_OP_PRIM_DEVTYPE_RECORD 1
666 #define CEC_OP_PRIM_DEVTYPE_TUNER 3
667 #define CEC_OP_PRIM_DEVTYPE_PLAYBACK 4
668 #define CEC_OP_PRIM_DEVTYPE_AUDIOSYSTEM 5
669 #define CEC_OP_PRIM_DEVTYPE_SWITCH 6
670 #define CEC_OP_PRIM_DEVTYPE_PROCESSOR 7
671
672 #define CEC_MSG_SET_MENU_LANGUAGE 0x32
673 #define CEC_MSG_REPORT_FEATURES 0xa6 /* HDMI 2.0 */
674 /* All Device Types Operand (all_device_types) */
675 #define CEC_OP_ALL_DEVTYPE_TV 0x80
676 #define CEC_OP_ALL_DEVTYPE_RECORD 0x40
677 #define CEC_OP_ALL_DEVTYPE_TUNER 0x20
678 #define CEC_OP_ALL_DEVTYPE_PLAYBACK 0x10
679 #define CEC_OP_ALL_DEVTYPE_AUDIOSYSTEM 0x08
680 #define CEC_OP_ALL_DEVTYPE_SWITCH 0x04
681 /*
682 * And if you wondering what happened to PROCESSOR devices: those should
683 * be mapped to a SWITCH.
684 */
685
686 /* Valid for RC Profile and Device Feature operands */
687 #define CEC_OP_FEAT_EXT 0x80 /* Extension bit */
688 /* RC Profile Operand (rc_profile) */
689 #define CEC_OP_FEAT_RC_TV_PROFILE_NONE 0x00
690 #define CEC_OP_FEAT_RC_TV_PROFILE_1 0x02
691 #define CEC_OP_FEAT_RC_TV_PROFILE_2 0x06
692 #define CEC_OP_FEAT_RC_TV_PROFILE_3 0x0a
693 #define CEC_OP_FEAT_RC_TV_PROFILE_4 0x0e
694 #define CEC_OP_FEAT_RC_SRC_HAS_DEV_ROOT_MENU 0x50
695 #define CEC_OP_FEAT_RC_SRC_HAS_DEV_SETUP_MENU 0x48
696 #define CEC_OP_FEAT_RC_SRC_HAS_CONTENTS_MENU 0x44
697 #define CEC_OP_FEAT_RC_SRC_HAS_MEDIA_TOP_MENU 0x42
698 #define CEC_OP_FEAT_RC_SRC_HAS_MEDIA_CONTEXT_MENU 0x41
699 /* Device Feature Operand (dev_features) */
700 #define CEC_OP_FEAT_DEV_HAS_RECORD_TV_SCREEN 0x40
701 #define CEC_OP_FEAT_DEV_HAS_SET_OSD_STRING 0x20
702 #define CEC_OP_FEAT_DEV_HAS_DECK_CONTROL 0x10
703 #define CEC_OP_FEAT_DEV_HAS_SET_AUDIO_RATE 0x08
704 #define CEC_OP_FEAT_DEV_SINK_HAS_ARC_TX 0x04
705 #define CEC_OP_FEAT_DEV_SOURCE_HAS_ARC_RX 0x02
706
707 #define CEC_MSG_GIVE_FEATURES 0xa5 /* HDMI 2.0 */
708
709
710 /* Deck Control Feature */
711 #define CEC_MSG_DECK_CONTROL 0x42
712 /* Deck Control Mode Operand (deck_control_mode) */
713 #define CEC_OP_DECK_CTL_MODE_SKIP_FWD 1
714 #define CEC_OP_DECK_CTL_MODE_SKIP_REV 2
715 #define CEC_OP_DECK_CTL_MODE_STOP 3
716 #define CEC_OP_DECK_CTL_MODE_EJECT 4
717
718 #define CEC_MSG_DECK_STATUS 0x1b
719 /* Deck Info Operand (deck_info) */
720 #define CEC_OP_DECK_INFO_PLAY 0x11
721 #define CEC_OP_DECK_INFO_RECORD 0x12
722 #define CEC_OP_DECK_INFO_PLAY_REV 0x13
723 #define CEC_OP_DECK_INFO_STILL 0x14
724 #define CEC_OP_DECK_INFO_SLOW 0x15
725 #define CEC_OP_DECK_INFO_SLOW_REV 0x16
726 #define CEC_OP_DECK_INFO_FAST_FWD 0x17
727 #define CEC_OP_DECK_INFO_FAST_REV 0x18
728 #define CEC_OP_DECK_INFO_NO_MEDIA 0x19
729 #define CEC_OP_DECK_INFO_STOP 0x1a
730 #define CEC_OP_DECK_INFO_SKIP_FWD 0x1b
731 #define CEC_OP_DECK_INFO_SKIP_REV 0x1c
732 #define CEC_OP_DECK_INFO_INDEX_SEARCH_FWD 0x1d
733 #define CEC_OP_DECK_INFO_INDEX_SEARCH_REV 0x1e
734 #define CEC_OP_DECK_INFO_OTHER 0x1f
735
736 #define CEC_MSG_GIVE_DECK_STATUS 0x1a
737 /* Status Request Operand (status_req) */
738 #define CEC_OP_STATUS_REQ_ON 1
739 #define CEC_OP_STATUS_REQ_OFF 2
740 #define CEC_OP_STATUS_REQ_ONCE 3
741
742 #define CEC_MSG_PLAY 0x41
743 /* Play Mode Operand (play_mode) */
744 #define CEC_OP_PLAY_MODE_PLAY_FWD 0x24
745 #define CEC_OP_PLAY_MODE_PLAY_REV 0x20
746 #define CEC_OP_PLAY_MODE_PLAY_STILL 0x25
747 #define CEC_OP_PLAY_MODE_PLAY_FAST_FWD_MIN 0x05
748 #define CEC_OP_PLAY_MODE_PLAY_FAST_FWD_MED 0x06
749 #define CEC_OP_PLAY_MODE_PLAY_FAST_FWD_MAX 0x07
750 #define CEC_OP_PLAY_MODE_PLAY_FAST_REV_MIN 0x09
751 #define CEC_OP_PLAY_MODE_PLAY_FAST_REV_MED 0x0a
752 #define CEC_OP_PLAY_MODE_PLAY_FAST_REV_MAX 0x0b
753 #define CEC_OP_PLAY_MODE_PLAY_SLOW_FWD_MIN 0x15
754 #define CEC_OP_PLAY_MODE_PLAY_SLOW_FWD_MED 0x16
755 #define CEC_OP_PLAY_MODE_PLAY_SLOW_FWD_MAX 0x17
756 #define CEC_OP_PLAY_MODE_PLAY_SLOW_REV_MIN 0x19
757 #define CEC_OP_PLAY_MODE_PLAY_SLOW_REV_MED 0x1a
758 #define CEC_OP_PLAY_MODE_PLAY_SLOW_REV_MAX 0x1b
759
760
761 /* Tuner Control Feature */
762 #define CEC_MSG_GIVE_TUNER_DEVICE_STATUS 0x08
763 #define CEC_MSG_SELECT_ANALOGUE_SERVICE 0x92
764 #define CEC_MSG_SELECT_DIGITAL_SERVICE 0x93
765 #define CEC_MSG_TUNER_DEVICE_STATUS 0x07
766 /* Recording Flag Operand (rec_flag) */
767 #define CEC_OP_REC_FLAG_USED 0
768 #define CEC_OP_REC_FLAG_NOT_USED 1
769 /* Tuner Display Info Operand (tuner_display_info) */
770 #define CEC_OP_TUNER_DISPLAY_INFO_DIGITAL 0
771 #define CEC_OP_TUNER_DISPLAY_INFO_NONE 1
772 #define CEC_OP_TUNER_DISPLAY_INFO_ANALOGUE 2
773
774 #define CEC_MSG_TUNER_STEP_DECREMENT 0x06
775 #define CEC_MSG_TUNER_STEP_INCREMENT 0x05
776
777
778 /* Vendor Specific Commands Feature */
779
780 /*
781 * Has also:
782 * CEC_MSG_CEC_VERSION
783 * CEC_MSG_GET_CEC_VERSION
784 */
785 #define CEC_MSG_DEVICE_VENDOR_ID 0x87
786 #define CEC_MSG_GIVE_DEVICE_VENDOR_ID 0x8c
787 #define CEC_MSG_VENDOR_COMMAND 0x89
788 #define CEC_MSG_VENDOR_COMMAND_WITH_ID 0xa0
789 #define CEC_MSG_VENDOR_REMOTE_BUTTON_DOWN 0x8a
790 #define CEC_MSG_VENDOR_REMOTE_BUTTON_UP 0x8b
791
792
793 /* OSD Display Feature */
794 #define CEC_MSG_SET_OSD_STRING 0x64
795 /* Display Control Operand (disp_ctl) */
796 #define CEC_OP_DISP_CTL_DEFAULT 0x00
797 #define CEC_OP_DISP_CTL_UNTIL_CLEARED 0x40
798 #define CEC_OP_DISP_CTL_CLEAR 0x80
799
800
801 /* Device OSD Transfer Feature */
802 #define CEC_MSG_GIVE_OSD_NAME 0x46
803 #define CEC_MSG_SET_OSD_NAME 0x47
804
805
806 /* Device Menu Control Feature */
807 #define CEC_MSG_MENU_REQUEST 0x8d
808 /* Menu Request Type Operand (menu_req) */
809 #define CEC_OP_MENU_REQUEST_ACTIVATE 0x00
810 #define CEC_OP_MENU_REQUEST_DEACTIVATE 0x01
811 #define CEC_OP_MENU_REQUEST_QUERY 0x02
812
813 #define CEC_MSG_MENU_STATUS 0x8e
814 /* Menu State Operand (menu_state) */
815 #define CEC_OP_MENU_STATE_ACTIVATED 0x00
816 #define CEC_OP_MENU_STATE_DEACTIVATED 0x01
817
818 #define CEC_MSG_USER_CONTROL_PRESSED 0x44
819 /* UI Broadcast Type Operand (ui_bcast_type) */
820 #define CEC_OP_UI_BCAST_TYPE_TOGGLE_ALL 0x00
821 #define CEC_OP_UI_BCAST_TYPE_TOGGLE_DIG_ANA 0x01
822 #define CEC_OP_UI_BCAST_TYPE_ANALOGUE 0x10
823 #define CEC_OP_UI_BCAST_TYPE_ANALOGUE_T 0x20
824 #define CEC_OP_UI_BCAST_TYPE_ANALOGUE_CABLE 0x30
825 #define CEC_OP_UI_BCAST_TYPE_ANALOGUE_SAT 0x40
826 #define CEC_OP_UI_BCAST_TYPE_DIGITAL 0x50
827 #define CEC_OP_UI_BCAST_TYPE_DIGITAL_T 0x60
828 #define CEC_OP_UI_BCAST_TYPE_DIGITAL_CABLE 0x70
829 #define CEC_OP_UI_BCAST_TYPE_DIGITAL_SAT 0x80
830 #define CEC_OP_UI_BCAST_TYPE_DIGITAL_COM_SAT 0x90
831 #define CEC_OP_UI_BCAST_TYPE_DIGITAL_COM_SAT2 0x91
832 #define CEC_OP_UI_BCAST_TYPE_IP 0xa0
833 /* UI Sound Presentation Control Operand (ui_snd_pres_ctl) */
834 #define CEC_OP_UI_SND_PRES_CTL_DUAL_MONO 0x10
835 #define CEC_OP_UI_SND_PRES_CTL_KARAOKE 0x20
836 #define CEC_OP_UI_SND_PRES_CTL_DOWNMIX 0x80
837 #define CEC_OP_UI_SND_PRES_CTL_REVERB 0x90
838 #define CEC_OP_UI_SND_PRES_CTL_EQUALIZER 0xa0
839 #define CEC_OP_UI_SND_PRES_CTL_BASS_UP 0xb1
840 #define CEC_OP_UI_SND_PRES_CTL_BASS_NEUTRAL 0xb2
841 #define CEC_OP_UI_SND_PRES_CTL_BASS_DOWN 0xb3
842 #define CEC_OP_UI_SND_PRES_CTL_TREBLE_UP 0xc1
843 #define CEC_OP_UI_SND_PRES_CTL_TREBLE_NEUTRAL 0xc2
844 #define CEC_OP_UI_SND_PRES_CTL_TREBLE_DOWN 0xc3
845
846 #define CEC_MSG_USER_CONTROL_RELEASED 0x45
847
848
849 /* Remote Control Passthrough Feature */
850
851 /*
852 * Has also:
853 * CEC_MSG_USER_CONTROL_PRESSED
854 * CEC_MSG_USER_CONTROL_RELEASED
855 */
856
857
858 /* Power Status Feature */
859 #define CEC_MSG_GIVE_DEVICE_POWER_STATUS 0x8f
860 #define CEC_MSG_REPORT_POWER_STATUS 0x90
861 /* Power Status Operand (pwr_state) */
862 #define CEC_OP_POWER_STATUS_ON 0
863 #define CEC_OP_POWER_STATUS_STANDBY 1
864 #define CEC_OP_POWER_STATUS_TO_ON 2
865 #define CEC_OP_POWER_STATUS_TO_STANDBY 3
866
867
868 /* General Protocol Messages */
869 #define CEC_MSG_FEATURE_ABORT 0x00
870 /* Abort Reason Operand (reason) */
871 #define CEC_OP_ABORT_UNRECOGNIZED_OP 0
872 #define CEC_OP_ABORT_INCORRECT_MODE 1
873 #define CEC_OP_ABORT_NO_SOURCE 2
874 #define CEC_OP_ABORT_INVALID_OP 3
875 #define CEC_OP_ABORT_REFUSED 4
876 #define CEC_OP_ABORT_UNDETERMINED 5
877
878 #define CEC_MSG_ABORT 0xff
879
880
881 /* System Audio Control Feature */
882
883 /*
884 * Has also:
885 * CEC_MSG_USER_CONTROL_PRESSED
886 * CEC_MSG_USER_CONTROL_RELEASED
887 */
888 #define CEC_MSG_GIVE_AUDIO_STATUS 0x71
889 #define CEC_MSG_GIVE_SYSTEM_AUDIO_MODE_STATUS 0x7d
890 #define CEC_MSG_REPORT_AUDIO_STATUS 0x7a
891 /* Audio Mute Status Operand (aud_mute_status) */
892 #define CEC_OP_AUD_MUTE_STATUS_OFF 0
893 #define CEC_OP_AUD_MUTE_STATUS_ON 1
894
895 #define CEC_MSG_REPORT_SHORT_AUDIO_DESCRIPTOR 0xa3
896 #define CEC_MSG_REQUEST_SHORT_AUDIO_DESCRIPTOR 0xa4
897 #define CEC_MSG_SET_SYSTEM_AUDIO_MODE 0x72
898 /* System Audio Status Operand (sys_aud_status) */
899 #define CEC_OP_SYS_AUD_STATUS_OFF 0
900 #define CEC_OP_SYS_AUD_STATUS_ON 1
901
902 #define CEC_MSG_SYSTEM_AUDIO_MODE_REQUEST 0x70
903 #define CEC_MSG_SYSTEM_AUDIO_MODE_STATUS 0x7e
904 /* Audio Format ID Operand (audio_format_id) */
905 #define CEC_OP_AUD_FMT_ID_CEA861 0
906 #define CEC_OP_AUD_FMT_ID_CEA861_CXT 1
907
908
909 /* Audio Rate Control Feature */
910 #define CEC_MSG_SET_AUDIO_RATE 0x9a
911 /* Audio Rate Operand (audio_rate) */
912 #define CEC_OP_AUD_RATE_OFF 0
913 #define CEC_OP_AUD_RATE_WIDE_STD 1
914 #define CEC_OP_AUD_RATE_WIDE_FAST 2
915 #define CEC_OP_AUD_RATE_WIDE_SLOW 3
916 #define CEC_OP_AUD_RATE_NARROW_STD 4
917 #define CEC_OP_AUD_RATE_NARROW_FAST 5
918 #define CEC_OP_AUD_RATE_NARROW_SLOW 6
919
920
921 /* Audio Return Channel Control Feature */
922 #define CEC_MSG_INITIATE_ARC 0xc0
923 #define CEC_MSG_REPORT_ARC_INITIATED 0xc1
924 #define CEC_MSG_REPORT_ARC_TERMINATED 0xc2
925 #define CEC_MSG_REQUEST_ARC_INITIATION 0xc3
926 #define CEC_MSG_REQUEST_ARC_TERMINATION 0xc4
927 #define CEC_MSG_TERMINATE_ARC 0xc5
928
929
930 /* Dynamic Audio Lipsync Feature */
931 /* Only for CEC 2.0 and up */
932 #define CEC_MSG_REQUEST_CURRENT_LATENCY 0xa7
933 #define CEC_MSG_REPORT_CURRENT_LATENCY 0xa8
934 /* Low Latency Mode Operand (low_latency_mode) */
935 #define CEC_OP_LOW_LATENCY_MODE_OFF 0
936 #define CEC_OP_LOW_LATENCY_MODE_ON 1
937 /* Audio Output Compensated Operand (audio_out_compensated) */
938 #define CEC_OP_AUD_OUT_COMPENSATED_NA 0
939 #define CEC_OP_AUD_OUT_COMPENSATED_DELAY 1
940 #define CEC_OP_AUD_OUT_COMPENSATED_NO_DELAY 2
941 #define CEC_OP_AUD_OUT_COMPENSATED_PARTIAL_DELAY 3
942
943
944 /* Capability Discovery and Control Feature */
945 #define CEC_MSG_CDC_MESSAGE 0xf8
946 /* Ethernet-over-HDMI: nobody ever does this... */
947 #define CEC_MSG_CDC_HEC_INQUIRE_STATE 0x00
948 #define CEC_MSG_CDC_HEC_REPORT_STATE 0x01
949 /* HEC Functionality State Operand (hec_func_state) */
950 #define CEC_OP_HEC_FUNC_STATE_NOT_SUPPORTED 0
951 #define CEC_OP_HEC_FUNC_STATE_INACTIVE 1
952 #define CEC_OP_HEC_FUNC_STATE_ACTIVE 2
953 #define CEC_OP_HEC_FUNC_STATE_ACTIVATION_FIELD 3
954 /* Host Functionality State Operand (host_func_state) */
955 #define CEC_OP_HOST_FUNC_STATE_NOT_SUPPORTED 0
956 #define CEC_OP_HOST_FUNC_STATE_INACTIVE 1
957 #define CEC_OP_HOST_FUNC_STATE_ACTIVE 2
958 /* ENC Functionality State Operand (enc_func_state) */
959 #define CEC_OP_ENC_FUNC_STATE_EXT_CON_NOT_SUPPORTED 0
960 #define CEC_OP_ENC_FUNC_STATE_EXT_CON_INACTIVE 1
961 #define CEC_OP_ENC_FUNC_STATE_EXT_CON_ACTIVE 2
962 /* CDC Error Code Operand (cdc_errcode) */
963 #define CEC_OP_CDC_ERROR_CODE_NONE 0
964 #define CEC_OP_CDC_ERROR_CODE_CAP_UNSUPPORTED 1
965 #define CEC_OP_CDC_ERROR_CODE_WRONG_STATE 2
966 #define CEC_OP_CDC_ERROR_CODE_OTHER 3
967 /* HEC Support Operand (hec_support) */
968 #define CEC_OP_HEC_SUPPORT_NO 0
969 #define CEC_OP_HEC_SUPPORT_YES 1
970 /* HEC Activation Operand (hec_activation) */
971 #define CEC_OP_HEC_ACTIVATION_ON 0
972 #define CEC_OP_HEC_ACTIVATION_OFF 1
973
974 #define CEC_MSG_CDC_HEC_SET_STATE_ADJACENT 0x02
975 #define CEC_MSG_CDC_HEC_SET_STATE 0x03
976 /* HEC Set State Operand (hec_set_state) */
977 #define CEC_OP_HEC_SET_STATE_DEACTIVATE 0
978 #define CEC_OP_HEC_SET_STATE_ACTIVATE 1
979
980 #define CEC_MSG_CDC_HEC_REQUEST_DEACTIVATION 0x04
981 #define CEC_MSG_CDC_HEC_NOTIFY_ALIVE 0x05
982 #define CEC_MSG_CDC_HEC_DISCOVER 0x06
983 /* Hotplug Detect messages */
984 #define CEC_MSG_CDC_HPD_SET_STATE 0x10
985 /* HPD State Operand (hpd_state) */
986 #define CEC_OP_HPD_STATE_CP_EDID_DISABLE 0
987 #define CEC_OP_HPD_STATE_CP_EDID_ENABLE 1
988 #define CEC_OP_HPD_STATE_CP_EDID_DISABLE_ENABLE 2
989 #define CEC_OP_HPD_STATE_EDID_DISABLE 3
990 #define CEC_OP_HPD_STATE_EDID_ENABLE 4
991 #define CEC_OP_HPD_STATE_EDID_DISABLE_ENABLE 5
992 #define CEC_MSG_CDC_HPD_REPORT_STATE 0x11
993 /* HPD Error Code Operand (hpd_error) */
994 #define CEC_OP_HPD_ERROR_NONE 0
995 #define CEC_OP_HPD_ERROR_INITIATOR_NOT_CAPABLE 1
996 #define CEC_OP_HPD_ERROR_INITIATOR_WRONG_STATE 2
997 #define CEC_OP_HPD_ERROR_OTHER 3
998 #define CEC_OP_HPD_ERROR_NONE_NO_VIDEO 4
999
1000 /* End of Messages */
1001
1002 /* Helper functions to identify the 'special' CEC devices */
1003
cec_is_2nd_tv(const struct cec_log_addrs * las)1004 static inline int cec_is_2nd_tv(const struct cec_log_addrs *las)
1005 {
1006 /*
1007 * It is a second TV if the logical address is 14 or 15 and the
1008 * primary device type is a TV.
1009 */
1010 return las->num_log_addrs &&
1011 las->log_addr[0] >= CEC_LOG_ADDR_SPECIFIC &&
1012 las->primary_device_type[0] == CEC_OP_PRIM_DEVTYPE_TV;
1013 }
1014
cec_is_processor(const struct cec_log_addrs * las)1015 static inline int cec_is_processor(const struct cec_log_addrs *las)
1016 {
1017 /*
1018 * It is a processor if the logical address is 12-15 and the
1019 * primary device type is a Processor.
1020 */
1021 return las->num_log_addrs &&
1022 las->log_addr[0] >= CEC_LOG_ADDR_BACKUP_1 &&
1023 las->primary_device_type[0] == CEC_OP_PRIM_DEVTYPE_PROCESSOR;
1024 }
1025
cec_is_switch(const struct cec_log_addrs * las)1026 static inline int cec_is_switch(const struct cec_log_addrs *las)
1027 {
1028 /*
1029 * It is a switch if the logical address is 15 and the
1030 * primary device type is a Switch and the CDC-Only flag is not set.
1031 */
1032 return las->num_log_addrs == 1 &&
1033 las->log_addr[0] == CEC_LOG_ADDR_UNREGISTERED &&
1034 las->primary_device_type[0] == CEC_OP_PRIM_DEVTYPE_SWITCH &&
1035 !(las->flags & CEC_LOG_ADDRS_FL_CDC_ONLY);
1036 }
1037
cec_is_cdc_only(const struct cec_log_addrs * las)1038 static inline int cec_is_cdc_only(const struct cec_log_addrs *las)
1039 {
1040 /*
1041 * It is a CDC-only device if the logical address is 15 and the
1042 * primary device type is a Switch and the CDC-Only flag is set.
1043 */
1044 return las->num_log_addrs == 1 &&
1045 las->log_addr[0] == CEC_LOG_ADDR_UNREGISTERED &&
1046 las->primary_device_type[0] == CEC_OP_PRIM_DEVTYPE_SWITCH &&
1047 (las->flags & CEC_LOG_ADDRS_FL_CDC_ONLY);
1048 }
1049
1050 #endif
1051
