1 /*
2 * Radisys 82600 Embedded chipset Memory Controller kernel module
3 * (C) 2005 EADS Astrium
4 * This file may be distributed under the terms of the
5 * GNU General Public License.
6 *
7 * Written by Tim Small <tim@buttersideup.com>, based on work by Thayne
8 * Harbaugh, Dan Hollis <goemon at anime dot net> and others.
9 *
10 * $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $
11 *
12 * Written with reference to 82600 High Integration Dual PCI System
13 * Controller Data Book:
14 * www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf
15 * references to this document given in []
16 */
17
18 #include <linux/module.h>
19 #include <linux/init.h>
20 #include <linux/pci.h>
21 #include <linux/pci_ids.h>
22 #include <linux/edac.h>
23 #include "edac_module.h"
24
25 #define EDAC_MOD_STR "r82600_edac"
26
27 #define r82600_printk(level, fmt, arg...) \
28 edac_printk(level, "r82600", fmt, ##arg)
29
30 #define r82600_mc_printk(mci, level, fmt, arg...) \
31 edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg)
32
33 /* Radisys say "The 82600 integrates a main memory SDRAM controller that
34 * supports up to four banks of memory. The four banks can support a mix of
35 * sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
36 * each of which can be any size from 16MB to 512MB. Both registered (control
37 * signals buffered) and unbuffered DIMM types are supported. Mixing of
38 * registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs
39 * is not allowed. The 82600 SDRAM interface operates at the same frequency as
40 * the CPU bus, 66MHz, 100MHz or 133MHz."
41 */
42
43 #define R82600_NR_CSROWS 4
44 #define R82600_NR_CHANS 1
45 #define R82600_NR_DIMMS 4
46
47 #define R82600_BRIDGE_ID 0x8200
48
49 /* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */
50 #define R82600_DRAMC 0x57 /* Various SDRAM related control bits
51 * all bits are R/W
52 *
53 * 7 SDRAM ISA Hole Enable
54 * 6 Flash Page Mode Enable
55 * 5 ECC Enable: 1=ECC 0=noECC
56 * 4 DRAM DIMM Type: 1=
57 * 3 BIOS Alias Disable
58 * 2 SDRAM BIOS Flash Write Enable
59 * 1:0 SDRAM Refresh Rate: 00=Disabled
60 * 01=7.8usec (256Mbit SDRAMs)
61 * 10=15.6us 11=125usec
62 */
63
64 #define R82600_SDRAMC 0x76 /* "SDRAM Control Register"
65 * More SDRAM related control bits
66 * all bits are R/W
67 *
68 * 15:8 Reserved.
69 *
70 * 7:5 Special SDRAM Mode Select
71 *
72 * 4 Force ECC
73 *
74 * 1=Drive ECC bits to 0 during
75 * write cycles (i.e. ECC test mode)
76 *
77 * 0=Normal ECC functioning
78 *
79 * 3 Enhanced Paging Enable
80 *
81 * 2 CAS# Latency 0=3clks 1=2clks
82 *
83 * 1 RAS# to CAS# Delay 0=3 1=2
84 *
85 * 0 RAS# Precharge 0=3 1=2
86 */
87
88 #define R82600_EAP 0x80 /* ECC Error Address Pointer Register
89 *
90 * 31 Disable Hardware Scrubbing (RW)
91 * 0=Scrub on corrected read
92 * 1=Don't scrub on corrected read
93 *
94 * 30:12 Error Address Pointer (RO)
95 * Upper 19 bits of error address
96 *
97 * 11:4 Syndrome Bits (RO)
98 *
99 * 3 BSERR# on multibit error (RW)
100 * 1=enable 0=disable
101 *
102 * 2 NMI on Single Bit Eror (RW)
103 * 1=NMI triggered by SBE n.b. other
104 * prerequeists
105 * 0=NMI not triggered
106 *
107 * 1 MBE (R/WC)
108 * read 1=MBE at EAP (see above)
109 * read 0=no MBE, or SBE occurred first
110 * write 1=Clear MBE status (must also
111 * clear SBE)
112 * write 0=NOP
113 *
114 * 1 SBE (R/WC)
115 * read 1=SBE at EAP (see above)
116 * read 0=no SBE, or MBE occurred first
117 * write 1=Clear SBE status (must also
118 * clear MBE)
119 * write 0=NOP
120 */
121
122 #define R82600_DRBA 0x60 /* + 0x60..0x63 SDRAM Row Boundary Address
123 * Registers
124 *
125 * 7:0 Address lines 30:24 - upper limit of
126 * each row [p57]
127 */
128
129 struct r82600_error_info {
130 u32 eapr;
131 };
132
133 static bool disable_hardware_scrub;
134
135 static struct edac_pci_ctl_info *r82600_pci;
136
r82600_get_error_info(struct mem_ctl_info * mci,struct r82600_error_info * info)137 static void r82600_get_error_info(struct mem_ctl_info *mci,
138 struct r82600_error_info *info)
139 {
140 struct pci_dev *pdev;
141
142 pdev = to_pci_dev(mci->pdev);
143 pci_read_config_dword(pdev, R82600_EAP, &info->eapr);
144
145 if (info->eapr & BIT(0))
146 /* Clear error to allow next error to be reported [p.62] */
147 pci_write_bits32(pdev, R82600_EAP,
148 ((u32) BIT(0) & (u32) BIT(1)),
149 ((u32) BIT(0) & (u32) BIT(1)));
150
151 if (info->eapr & BIT(1))
152 /* Clear error to allow next error to be reported [p.62] */
153 pci_write_bits32(pdev, R82600_EAP,
154 ((u32) BIT(0) & (u32) BIT(1)),
155 ((u32) BIT(0) & (u32) BIT(1)));
156 }
157
r82600_process_error_info(struct mem_ctl_info * mci,struct r82600_error_info * info,int handle_errors)158 static int r82600_process_error_info(struct mem_ctl_info *mci,
159 struct r82600_error_info *info,
160 int handle_errors)
161 {
162 int error_found;
163 u32 eapaddr, page;
164 u32 syndrome;
165
166 error_found = 0;
167
168 /* bits 30:12 store the upper 19 bits of the 32 bit error address */
169 eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13;
170 /* Syndrome in bits 11:4 [p.62] */
171 syndrome = (info->eapr >> 4) & 0xFF;
172
173 /* the R82600 reports at less than page *
174 * granularity (upper 19 bits only) */
175 page = eapaddr >> PAGE_SHIFT;
176
177 if (info->eapr & BIT(0)) { /* CE? */
178 error_found = 1;
179
180 if (handle_errors)
181 edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci, 1,
182 page, 0, syndrome,
183 edac_mc_find_csrow_by_page(mci, page),
184 0, -1,
185 mci->ctl_name, "");
186 }
187
188 if (info->eapr & BIT(1)) { /* UE? */
189 error_found = 1;
190
191 if (handle_errors)
192 /* 82600 doesn't give enough info */
193 edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci, 1,
194 page, 0, 0,
195 edac_mc_find_csrow_by_page(mci, page),
196 0, -1,
197 mci->ctl_name, "");
198 }
199
200 return error_found;
201 }
202
r82600_check(struct mem_ctl_info * mci)203 static void r82600_check(struct mem_ctl_info *mci)
204 {
205 struct r82600_error_info info;
206
207 edac_dbg(1, "MC%d\n", mci->mc_idx);
208 r82600_get_error_info(mci, &info);
209 r82600_process_error_info(mci, &info, 1);
210 }
211
ecc_enabled(u8 dramcr)212 static inline int ecc_enabled(u8 dramcr)
213 {
214 return dramcr & BIT(5);
215 }
216
r82600_init_csrows(struct mem_ctl_info * mci,struct pci_dev * pdev,u8 dramcr)217 static void r82600_init_csrows(struct mem_ctl_info *mci, struct pci_dev *pdev,
218 u8 dramcr)
219 {
220 struct csrow_info *csrow;
221 struct dimm_info *dimm;
222 int index;
223 u8 drbar; /* SDRAM Row Boundary Address Register */
224 u32 row_high_limit, row_high_limit_last;
225 u32 reg_sdram, ecc_on, row_base;
226
227 ecc_on = ecc_enabled(dramcr);
228 reg_sdram = dramcr & BIT(4);
229 row_high_limit_last = 0;
230
231 for (index = 0; index < mci->nr_csrows; index++) {
232 csrow = mci->csrows[index];
233 dimm = csrow->channels[0]->dimm;
234
235 /* find the DRAM Chip Select Base address and mask */
236 pci_read_config_byte(pdev, R82600_DRBA + index, &drbar);
237
238 edac_dbg(1, "Row=%d DRBA = %#0x\n", index, drbar);
239
240 row_high_limit = ((u32) drbar << 24);
241 /* row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */
242
243 edac_dbg(1, "Row=%d, Boundary Address=%#0x, Last = %#0x\n",
244 index, row_high_limit, row_high_limit_last);
245
246 /* Empty row [p.57] */
247 if (row_high_limit == row_high_limit_last)
248 continue;
249
250 row_base = row_high_limit_last;
251
252 csrow->first_page = row_base >> PAGE_SHIFT;
253 csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1;
254
255 dimm->nr_pages = csrow->last_page - csrow->first_page + 1;
256 /* Error address is top 19 bits - so granularity is *
257 * 14 bits */
258 dimm->grain = 1 << 14;
259 dimm->mtype = reg_sdram ? MEM_RDDR : MEM_DDR;
260 /* FIXME - check that this is unknowable with this chipset */
261 dimm->dtype = DEV_UNKNOWN;
262
263 /* Mode is global on 82600 */
264 dimm->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE;
265 row_high_limit_last = row_high_limit;
266 }
267 }
268
r82600_probe1(struct pci_dev * pdev,int dev_idx)269 static int r82600_probe1(struct pci_dev *pdev, int dev_idx)
270 {
271 struct mem_ctl_info *mci;
272 struct edac_mc_layer layers[2];
273 u8 dramcr;
274 u32 eapr;
275 u32 scrub_disabled;
276 u32 sdram_refresh_rate;
277 struct r82600_error_info discard;
278
279 edac_dbg(0, "\n");
280 pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
281 pci_read_config_dword(pdev, R82600_EAP, &eapr);
282 scrub_disabled = eapr & BIT(31);
283 sdram_refresh_rate = dramcr & (BIT(0) | BIT(1));
284 edac_dbg(2, "sdram refresh rate = %#0x\n", sdram_refresh_rate);
285 edac_dbg(2, "DRAMC register = %#0x\n", dramcr);
286 layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
287 layers[0].size = R82600_NR_CSROWS;
288 layers[0].is_virt_csrow = true;
289 layers[1].type = EDAC_MC_LAYER_CHANNEL;
290 layers[1].size = R82600_NR_CHANS;
291 layers[1].is_virt_csrow = false;
292 mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers, 0);
293 if (mci == NULL)
294 return -ENOMEM;
295
296 edac_dbg(0, "mci = %p\n", mci);
297 mci->pdev = &pdev->dev;
298 mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR;
299 mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
300 /* FIXME try to work out if the chip leads have been used for COM2
301 * instead on this board? [MA6?] MAYBE:
302 */
303
304 /* On the R82600, the pins for memory bits 72:65 - i.e. the *
305 * EC bits are shared with the pins for COM2 (!), so if COM2 *
306 * is enabled, we assume COM2 is wired up, and thus no EDAC *
307 * is possible. */
308 mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
309
310 if (ecc_enabled(dramcr)) {
311 if (scrub_disabled)
312 edac_dbg(3, "mci = %p - Scrubbing disabled! EAP: %#0x\n",
313 mci, eapr);
314 } else
315 mci->edac_cap = EDAC_FLAG_NONE;
316
317 mci->mod_name = EDAC_MOD_STR;
318 mci->ctl_name = "R82600";
319 mci->dev_name = pci_name(pdev);
320 mci->edac_check = r82600_check;
321 mci->ctl_page_to_phys = NULL;
322 r82600_init_csrows(mci, pdev, dramcr);
323 r82600_get_error_info(mci, &discard); /* clear counters */
324
325 /* Here we assume that we will never see multiple instances of this
326 * type of memory controller. The ID is therefore hardcoded to 0.
327 */
328 if (edac_mc_add_mc(mci)) {
329 edac_dbg(3, "failed edac_mc_add_mc()\n");
330 goto fail;
331 }
332
333 /* get this far and it's successful */
334
335 if (disable_hardware_scrub) {
336 edac_dbg(3, "Disabling Hardware Scrub (scrub on error)\n");
337 pci_write_bits32(pdev, R82600_EAP, BIT(31), BIT(31));
338 }
339
340 /* allocating generic PCI control info */
341 r82600_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR);
342 if (!r82600_pci) {
343 printk(KERN_WARNING
344 "%s(): Unable to create PCI control\n",
345 __func__);
346 printk(KERN_WARNING
347 "%s(): PCI error report via EDAC not setup\n",
348 __func__);
349 }
350
351 edac_dbg(3, "success\n");
352 return 0;
353
354 fail:
355 edac_mc_free(mci);
356 return -ENODEV;
357 }
358
359 /* returns count (>= 0), or negative on error */
r82600_init_one(struct pci_dev * pdev,const struct pci_device_id * ent)360 static int r82600_init_one(struct pci_dev *pdev,
361 const struct pci_device_id *ent)
362 {
363 edac_dbg(0, "\n");
364
365 /* don't need to call pci_enable_device() */
366 return r82600_probe1(pdev, ent->driver_data);
367 }
368
r82600_remove_one(struct pci_dev * pdev)369 static void r82600_remove_one(struct pci_dev *pdev)
370 {
371 struct mem_ctl_info *mci;
372
373 edac_dbg(0, "\n");
374
375 if (r82600_pci)
376 edac_pci_release_generic_ctl(r82600_pci);
377
378 if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL)
379 return;
380
381 edac_mc_free(mci);
382 }
383
384 static const struct pci_device_id r82600_pci_tbl[] = {
385 {
386 PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID)
387 },
388 {
389 0,
390 } /* 0 terminated list. */
391 };
392
393 MODULE_DEVICE_TABLE(pci, r82600_pci_tbl);
394
395 static struct pci_driver r82600_driver = {
396 .name = EDAC_MOD_STR,
397 .probe = r82600_init_one,
398 .remove = r82600_remove_one,
399 .id_table = r82600_pci_tbl,
400 };
401
r82600_init(void)402 static int __init r82600_init(void)
403 {
404 /* Ensure that the OPSTATE is set correctly for POLL or NMI */
405 opstate_init();
406
407 return pci_register_driver(&r82600_driver);
408 }
409
r82600_exit(void)410 static void __exit r82600_exit(void)
411 {
412 pci_unregister_driver(&r82600_driver);
413 }
414
415 module_init(r82600_init);
416 module_exit(r82600_exit);
417
418 MODULE_LICENSE("GPL");
419 MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. "
420 "on behalf of EADS Astrium");
421 MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers");
422
423 module_param(disable_hardware_scrub, bool, 0644);
424 MODULE_PARM_DESC(disable_hardware_scrub,
425 "If set, disable the chipset's automatic scrub for CEs");
426
427 module_param(edac_op_state, int, 0444);
428 MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");
429
