1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com)
4 */
5
6/*
7 * Device tree for AXC003 CPU card: HS38x UP configuration
8 */
9
10/include/ "skeleton_hs.dtsi"
11
12/ {
13	compatible = "snps,arc";
14	#address-cells = <2>;
15	#size-cells = <2>;
16
17	cpu_card {
18		compatible = "simple-bus";
19		#address-cells = <1>;
20		#size-cells = <1>;
21
22		ranges = <0x00000000 0x0 0xf0000000 0x10000000>;
23
24		input_clk: input-clk {
25			#clock-cells = <0>;
26			compatible = "fixed-clock";
27			clock-frequency = <33333333>;
28		};
29
30		core_clk: core-clk@80 {
31			compatible = "snps,axs10x-arc-pll-clock";
32			reg = <0x80 0x10>, <0x100 0x10>;
33			#clock-cells = <0>;
34			clocks = <&input_clk>;
35
36			/*
37			 * Set initial core pll output frequency to 90MHz.
38			 * It will be applied at the core pll driver probing
39			 * on early boot.
40			 */
41			assigned-clocks = <&core_clk>;
42			assigned-clock-rates = <90000000>;
43		};
44
45		core_intc: archs-intc@cpu {
46			compatible = "snps,archs-intc";
47			interrupt-controller;
48			#interrupt-cells = <1>;
49		};
50
51		/*
52		 * this GPIO block ORs all interrupts on CPU card (creg,..)
53		 * to uplink only 1 IRQ to ARC core intc
54		 */
55		dw-apb-gpio@2000 {
56			compatible = "snps,dw-apb-gpio";
57			reg = < 0x2000 0x80 >;
58			#address-cells = <1>;
59			#size-cells = <0>;
60
61			ictl_intc: gpio-controller@0 {
62				compatible = "snps,dw-apb-gpio-port";
63				gpio-controller;
64				#gpio-cells = <2>;
65				snps,nr-gpios = <30>;
66				reg = <0>;
67				interrupt-controller;
68				#interrupt-cells = <2>;
69				interrupt-parent = <&core_intc>;
70				interrupts = <25>;
71			};
72		};
73
74		debug_uart: dw-apb-uart@5000 {
75			compatible = "snps,dw-apb-uart";
76			reg = <0x5000 0x100>;
77			clock-frequency = <33333000>;
78			interrupt-parent = <&ictl_intc>;
79			interrupts = <2 4>;
80			baud = <115200>;
81			reg-shift = <2>;
82			reg-io-width = <4>;
83		};
84
85		arcpct0: pct {
86			compatible = "snps,archs-pct";
87			#interrupt-cells = <1>;
88			interrupt-parent = <&core_intc>;
89			interrupts = <20>;
90		};
91	};
92
93	/*
94	 * Mark DMA peripherals connected via IOC port as dma-coherent. We do
95	 * it via overlay because peripherals defined in axs10x_mb.dtsi are
96	 * used for both AXS101 and AXS103 boards and only AXS103 has IOC (so
97	 * only AXS103 board has HW-coherent DMA peripherals)
98	 * We don't need to mark pgu@17000 as dma-coherent because it uses
99	 * external DMA buffer located outside of IOC aperture.
100	 */
101	axs10x_mb {
102		ethernet@18000 {
103			dma-coherent;
104		};
105
106		ehci@40000 {
107			dma-coherent;
108		};
109
110		ohci@60000 {
111			dma-coherent;
112		};
113
114		mmc@15000 {
115			dma-coherent;
116		};
117	};
118
119	/*
120	 * The DW APB ICTL intc on MB is connected to CPU intc via a
121	 * DT "invisible" DW APB GPIO block, configured to simply pass thru
122	 * interrupts - setup accordinly in platform init (plat-axs10x/ax10x.c)
123	 *
124	 * So here we mimic a direct connection betwen them, ignoring the
125	 * ABPG GPIO. Thus set "interrupts = <24>" (DW APB GPIO to core)
126	 * instead of "interrupts = <12>" (DW APB ICTL to DW APB GPIO)
127	 *
128	 * This intc actually resides on MB, but we move it here to
129	 * avoid duplicating the MB dtsi file given that IRQ from
130	 * this intc to cpu intc are different for axs101 and axs103
131	 */
132	mb_intc: dw-apb-ictl@e0012000 {
133		#interrupt-cells = <1>;
134		compatible = "snps,dw-apb-ictl";
135		reg = < 0x0 0xe0012000 0x0 0x200 >;
136		interrupt-controller;
137		interrupt-parent = <&core_intc>;
138		interrupts = < 24 >;
139	};
140
141	memory {
142		device_type = "memory";
143		/* CONFIG_LINUX_RAM_BASE needs to match low mem start */
144		reg = <0x0 0x80000000 0x0 0x20000000	/* 512 MiB low mem */
145		       0x1 0xc0000000 0x0 0x40000000>;	/* 1 GiB highmem */
146	};
147
148	reserved-memory {
149		#address-cells = <2>;
150		#size-cells = <2>;
151		ranges;
152		/*
153		 * Move frame buffer out of IOC aperture (0x8z-0xaz).
154		 */
155		frame_buffer: frame_buffer@be000000 {
156			compatible = "shared-dma-pool";
157			reg = <0x0 0xbe000000 0x0 0x2000000>;
158			no-map;
159		};
160	};
161};
162