1HiSilicon STB PCIe host bridge DT description
2
3The HiSilicon STB PCIe host controller is based on the DesignWare PCIe core.
4It shares common functions with the DesignWare PCIe core driver and inherits
5common properties defined in
6Documentation/devicetree/bindings/pci/designware-pcie.txt.
7
8Additional properties are described here:
9
10Required properties
11- compatible: Should be one of the following strings:
12		"hisilicon,hi3798cv200-pcie"
13- reg: Should contain sysctl, rc_dbi, config registers location and length.
14- reg-names: Must include the following entries:
15  "control": control registers of PCIe controller;
16  "rc-dbi": configuration space of PCIe controller;
17  "config": configuration transaction space of PCIe controller.
18- bus-range: PCI bus numbers covered.
19- interrupts: MSI interrupt.
20- interrupt-names: Must include "msi" entries.
21- clocks: List of phandle and clock specifier pairs as listed in clock-names
22  property.
23- clock-name: Must include the following entries:
24  "aux": auxiliary gate clock;
25  "pipe": pipe gate clock;
26  "sys": sys gate clock;
27  "bus": bus gate clock.
28- resets: List of phandle and reset specifier pairs as listed in reset-names
29  property.
30- reset-names: Must include the following entries:
31  "soft": soft reset;
32  "sys": sys reset;
33  "bus": bus reset.
34
35Optional properties:
36- reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal.
37- vpcie-supply: The regulator in charge of PCIe port power.
38- phys: List of phandle and phy mode specifier, should be 0.
39- phy-names: Must be "phy".
40
41Example:
42	pcie@f9860000 {
43		compatible = "hisilicon,hi3798cv200-pcie";
44		reg = <0xf9860000 0x1000>,
45		      <0xf0000000 0x2000>,
46		      <0xf2000000 0x01000000>;
47		reg-names = "control", "rc-dbi", "config";
48		#address-cells = <3>;
49		#size-cells = <2>;
50		device_type = "pci";
51		bus-range = <0 15>;
52		num-lanes = <1>;
53		ranges=<0x81000000 0 0 0xf4000000 0 0x00010000
54			0x82000000 0 0xf3000000 0xf3000000 0 0x01000000>;
55		interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
56		interrupt-names = "msi";
57		#interrupt-cells = <1>;
58		interrupt-map-mask = <0 0 0 0>;
59		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
60		clocks = <&crg PCIE_AUX_CLK>,
61			 <&crg PCIE_PIPE_CLK>,
62			 <&crg PCIE_SYS_CLK>,
63			 <&crg PCIE_BUS_CLK>;
64		clock-names = "aux", "pipe", "sys", "bus";
65		resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>;
66		reset-names = "soft", "sys", "bus";
67		phys = <&combphy1 PHY_TYPE_PCIE>;
68		phy-names = "phy";
69	};
70