1* MDIO IO device
2
3The MDIO is a bus to which the PHY devices are connected.  For each
4device that exists on this bus, a child node should be created.  See
5the definition of the PHY node in booting-without-of.txt for an example
6of how to define a PHY.
7
8Required properties:
9  - reg : Offset and length of the register set for the device, and optionally
10          the offset and length of the TBIPA register (TBI PHY address
11	  register).  If TBIPA register is not specified, the driver will
12	  attempt to infer it from the register set specified (your mileage may
13	  vary).
14  - compatible : Should define the compatible device type for the
15    mdio. Currently supported strings/devices are:
16	- "fsl,gianfar-tbi"
17	- "fsl,gianfar-mdio"
18	- "fsl,etsec2-tbi"
19	- "fsl,etsec2-mdio"
20	- "fsl,ucc-mdio"
21	- "fsl,fman-mdio"
22    When device_type is "mdio", the following strings are also considered:
23	- "gianfar"
24	- "ucc_geth_phy"
25
26Example:
27
28	mdio@24520 {
29		reg = <24520 20>;
30		compatible = "fsl,gianfar-mdio";
31
32		ethernet-phy@0 {
33			......
34		};
35	};
36
37* TBI Internal MDIO bus
38
39As of this writing, every tsec is associated with an internal TBI PHY.
40This PHY is accessed through the local MDIO bus.  These buses are defined
41similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
42The TBI PHYs underneath them are similar to normal PHYs, but the reg property
43is considered instructive, rather than descriptive.  The reg property should
44be chosen so it doesn't interfere with other PHYs on the bus.
45
46* Gianfar-compatible ethernet nodes
47
48Properties:
49
50  - device_type : Should be "network"
51  - model : Model of the device.  Can be "TSEC", "eTSEC", or "FEC"
52  - compatible : Should be "gianfar"
53  - reg : Offset and length of the register set for the device
54  - interrupts : For FEC devices, the first interrupt is the device's
55    interrupt.  For TSEC and eTSEC devices, the first interrupt is
56    transmit, the second is receive, and the third is error.
57  - phy-handle : See ethernet.txt file in the same directory.
58  - fixed-link : See fixed-link.txt in the same directory.
59  - phy-connection-type : See ethernet.txt file in the same directory.
60    This property is only really needed if the connection is of type
61    "rgmii-id", as all other connection types are detected by hardware.
62  - fsl,magic-packet : If present, indicates that the hardware supports
63    waking up via magic packet.
64  - fsl,wake-on-filer : If present, indicates that the hardware supports
65    waking up by Filer General Purpose Interrupt (FGPI) asserted on the
66    Rx int line.  This is an advanced power management capability allowing
67    certain packet types (user) defined by filer rules to wake up the system.
68  - bd-stash : If present, indicates that the hardware supports stashing
69    buffer descriptors in the L2.
70  - rx-stash-len : Denotes the number of bytes of a received buffer to stash
71    in the L2.
72  - rx-stash-idx : Denotes the index of the first byte from the received
73    buffer to stash in the L2.
74
75Example:
76	ethernet@24000 {
77		device_type = "network";
78		model = "TSEC";
79		compatible = "gianfar";
80		reg = <0x24000 0x1000>;
81		local-mac-address = [ 00 E0 0C 00 73 00 ];
82		interrupts = <29 2 30 2 34 2>;
83		interrupt-parent = <&mpic>;
84		phy-handle = <&phy0>
85	};
86
87* Gianfar PTP clock nodes
88
89Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt
90