Searched full:wl18xx (Results 1 – 25 of 32) sorted by relevance
12
| /Linux-v6.1/Documentation/devicetree/bindings/net/wireless/ |
| D | ti,wlcore.yaml | 7 title: Texas Instruments Wilink 6/7/8 (wl12xx/wl18xx) Wireless LAN Controller
13 The wl12xx/wl18xx chips can be connected via SPI or via SDIO.
50 Points to the node of the regulator that powers/enable the wl12xx/wl18xx
107 // For wl18xx family:
|
| /Linux-v6.1/drivers/net/wireless/ti/wl18xx/ |
| D | Kconfig | 2 config WL18XX config
3 tristate "TI wl18xx support"
|
| D | Makefile | 2 wl18xx-objs = main.o acx.o tx.o io.o debugfs.o scan.o cmd.o event.o
4 obj-$(CONFIG_WL18XX) += wl18xx.o
|
| D | tx.c | 3 * This file is part of wl18xx
14 #include "wl18xx.h"
|
| D | debugfs.h | 3 * This file is part of wl18xx
|
| D | io.h | 3 * This file is part of wl18xx
|
| D | tx.h | 3 * This file is part of wl18xx
|
| D | io.c | 3 * This file is part of wl18xx
|
| D | acx.c | 3 * This file is part of wl18xx
13 #include "wl18xx.h"
|
| D | cmd.h | 3 * This file is part of wl18xx
|
| D | event.h | 3 * This file is part of wl18xx
|
| D | scan.h | 3 * This file is part of wl18xx
|
| D | conf.h | 3 * This file is part of wl18xx
|
| D | wl18xx.h | 3 * This file is part of wl18xx
|
| D | main.c | 3 * This file is part of wl18xx
29 #include "wl18xx.h"
659 #define WL18XX_FW_NAME "ti-connectivity/wl18xx-fw-4.bin"
670 /* wl18xx uses the same firmware for PLT */ in wl18xx_identify_chip()
1378 wl1271_info("wl18xx HW: %s, PG %d.%d (ROM 0x%x)", in wl18xx_get_pg_ver()
2029 { "wl18xx", 0 },
|
| D | cmd.c | 3 * This file is part of wl18xx
|
| D | debugfs.c | 3 * This file is part of wl18xx
16 #include "wl18xx.h"
|
| D | acx.h | 3 * This file is part of wl18xx
|
| /Linux-v6.1/drivers/net/wireless/ti/wlcore/ |
| D | sdio.c | 200 .name = "wl18xx",
201 .cfg_name = "ti-connectivity/wl18xx-conf.bin",
306 * Due to a hardware bug, we can't differentiate wl18xx from in wl1271_probe()
309 * which is 3.00 on the wl18xx chips. in wl1271_probe()
312 chip_family = "wl18xx"; in wl1271_probe()
|
| D | spi.c | 59 * wl18xx driver aggregation buffer size is (13 * 4K) compared to
60 * (4 * 4K) for wl12xx, so use the larger buffer needed for wl18xx
79 .name = "wl18xx",
80 .cfg_name = "ti-connectivity/wl18xx-conf.bin",
|
| D | io.c | 168 * wl18xx re-defines the HW_PART3 addresses for logger over in wlcore_set_partition()
|
| /Linux-v6.1/drivers/net/wireless/ti/ |
| D | Makefile | 5 obj-$(CONFIG_WL18XX) += wl18xx/
|
| D | Kconfig | 16 source "drivers/net/wireless/ti/wl18xx/Kconfig"
|
| /Linux-v6.1/Documentation/devicetree/bindings/net/ |
| D | ti,bluetooth.yaml | 18 * TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | imx6-logicpd-som.dtsi | 18 reg_wl18xx_vmmc: regulator-wl18xx {
|
12
