Home
last modified time | relevance | path

Searched full:transceiver (Results 1 – 25 of 377) sorted by relevance

12345678910>>...16

/Linux-v6.1/drivers/usb/phy/
DKconfig12 # USB Transceiver Drivers
15 tristate "AB8500 USB Transceiver Driver"
19 Enable this to support the USB OTG transceiver in AB8500 chip.
20 This transceiver supports high and full speed devices plus,
24 tristate "Freescale USB OTG Transceiver Driver"
29 Enable this to support Freescale USB OTG transceiver.
40 USB-On-The-Go transceiver working with the OMAP OTG controller.
41 The ISP1301 is a full speed USB transceiver which is used in
58 tristate "NOP USB Transceiver Driver"
62 This driver is to be used by all the usb transceiver which are either
[all …]
/Linux-v6.1/drivers/net/ieee802154/
DKconfig26 tristate "AT86RF230/231/233/212 transceiver driver"
37 tristate "Microchip MRF24J40 transceiver driver"
50 tristate "CC2520 transceiver driver"
60 tristate "ATUSB transceiver driver"
70 tristate "ADF7242 transceiver driver"
81 tristate "Cascoda CA8210 transceiver driver"
103 tristate "MCR20A transceiver driver"
/Linux-v6.1/drivers/power/supply/
Dpda_power.c37 static struct usb_phy *transceiver; variable
221 return (transceiver->last_event == USB_EVENT_VBUS || in otg_is_usb_online()
222 transceiver->last_event == USB_EVENT_ENUMERATED); in otg_is_usb_online()
227 return (transceiver->last_event == USB_EVENT_CHARGER); in otg_is_ac_online()
319 transceiver = usb_get_phy(USB_PHY_TYPE_USB2); in pda_power_probe()
320 if (!IS_ERR_OR_NULL(transceiver)) { in pda_power_probe()
376 if (!IS_ERR_OR_NULL(transceiver) && pdata->use_otg_notifier) { in pda_power_probe()
378 ret = usb_register_notifier(transceiver, &otg_nb); in pda_power_probe()
412 if (!IS_ERR_OR_NULL(transceiver)) in pda_power_probe()
413 usb_put_phy(transceiver); in pda_power_probe()
[all …]
/Linux-v6.1/drivers/nfc/st95hf/
DKconfig3 tristate "ST95HF NFC Transceiver driver"
6 This enables the ST NFC driver for ST95HF NFC transceiver.
7 This makes use of SPI framework to communicate with transceiver
10 Say Y here to compile support for ST NFC transceiver ST95HF
/Linux-v6.1/drivers/net/can/m_can/
Dm_can_platform.c84 struct phy *transceiver; in m_can_plat_probe() local
118 transceiver = devm_phy_optional_get(&pdev->dev, NULL); in m_can_plat_probe()
119 if (IS_ERR(transceiver)) { in m_can_plat_probe()
120 ret = PTR_ERR(transceiver); in m_can_plat_probe()
125 if (transceiver) in m_can_plat_probe()
126 mcan_class->can.bitrate_max = transceiver->attrs.max_link_rate; in m_can_plat_probe()
135 mcan_class->transceiver = transceiver; in m_can_plat_probe()
/Linux-v6.1/Documentation/devicetree/bindings/usb/
Disp1301.txt1 * NXP ISP1301 USB transceiver
8 - transceiver: phandle of isp1301 - this helps the ISP1301 driver to find the
13 isp1301: usb-transceiver@2c {
23 transceiver = <&isp1301>;
Dlpc32xx-udc.txt11 * External USB Transceiver Interrupt (OTG ATX)
12 - transceiver: phandle of the associated ISP1301 device - this is necessary for
17 isp1301: usb-transceiver@2c {
27 transceiver = <&isp1301>;
Dohci-nxp.txt8 - transceiver: phandle of the associated ISP1301 device - this is necessary for
13 isp1301: usb-transceiver@2c {
23 transceiver = <&isp1301>;
/Linux-v6.1/drivers/media/rc/
DKconfig149 tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
153 /transceiver made by ENE.
162 tristate "Fintek Consumer Infrared Transceiver"
166 /transceiver made by Fintek. This chip is found on assorted
216 tristate "IguanaWorks USB IR Transceiver"
219 Say Y here if you want to use the IguanaWorks USB IR Transceiver.
250 tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver"
262 tristate "Windows Media Center Ed. eHome Infrared Transceiver"
266 eHome Infrared Transceiver.
302 tristate "Nuvoton w836x7hg Consumer Infrared Transceiver"
[all …]
Dmceusb.c20 * remote/transceiver requirements and specification document, found at
36 #define DRIVER_DESC "Windows Media Center Ed. eHome Infrared Transceiver " \
123 /* Misc commands/responses not defined in the MCE remote/transceiver spec */
283 /* Original Microsoft MCE IR Transceiver (often HP-branded) */
286 /* Philips Infrared Transceiver - Sahara branded */
288 /* Philips Infrared Transceiver - HP branded */
293 /* Philips Infrared Transceiver - Omaura */
295 /* Philips Infrared Transceiver - Spinel plus */
297 /* Philips eHome Infrared Transceiver */
299 /* Philips/Spinel plus IR transceiver for ASUS */
[all …]
/Linux-v6.1/Documentation/devicetree/bindings/phy/
Dti,tcan104x-can.yaml7 title: TCAN104x CAN TRANSCEIVER PHY
26 gpio node to toggle standby signal on transceiver
31 gpio node to toggle enable signal on transceiver
43 transceiver.
/Linux-v6.1/arch/arm/boot/dts/
Dimx6ull-colibri-iris-v2.dts23 /* This turns the LVDS transceiver on */
34 * This switches the LVDS transceiver to the single-channel
45 * This switches the LVDS transceiver to the 24-bit RGB mode.
57 * This switches the LVDS transceiver to VESA color mapping mode.
Dimx6ull-colibri-wifi-iris-v2.dts23 /* This turns the LVDS transceiver on */
34 * This switches the LVDS transceiver to the single-channel
45 * This switches the LVDS transceiver to the 24-bit RGB mode.
57 * This switches the LVDS transceiver to VESA color mapping mode.
Dimx7d-colibri-iris-v2.dts31 * This switches the LVDS transceiver to VESA color mapping mode.
43 * This switches the LVDS transceiver to the 24-bit RGB mode.
53 * This switches the LVDS transceiver to the single-channel
63 /* This turns the LVDS transceiver on */
Dimx7s-colibri-iris-v2.dts31 * This switches the LVDS transceiver to VESA color mapping mode.
43 * This switches the LVDS transceiver to the 24-bit RGB mode.
53 * This switches the LVDS transceiver to the single-channel
63 /* This turns the LVDS transceiver on */
Dimx7-colibri-iris-v2.dtsi35 * uart_b_c_on_x14_enable turns the UART transceiver for UART2 and 5 on. If one wants to
36 * turn the transceiver off, that property has to be deleted and the gpio handled in
38 * The same applies to uart_a_on_x13_enable where the UART_A transceiver is turned on.
Dimx7-colibri-iris.dtsi34 * uart25 turns the UART transceiver for UART2 and 5 on. If one wants to turn the
35 * transceiver off, that property has to be deleted and the gpio handled in userspace.
36 * The same applies to uart1_tx_on where the UART1 transceiver is turned on.
Dimx6dl-colibri-iris.dts43 * uart-a-on-x13-enable turns the UART transceiver for UART_A on. If one
44 * wants to turn the transceiver off, that property has to be deleted
47 * UART_C transceiver is turned on.
/Linux-v6.1/Documentation/networking/device_drivers/ethernet/3com/
D3c509.rst46 IRQ, and transceiver settings, although this capability shouldn't generally be
53 transceiver type 3 (10base2). The flag "0x3c509" must be set to avoid conflicts
76 (b) You must be using your card's 10baseT transceiver (i.e., the RJ-45
107 Available Transceiver Types
110 For versions of the driver v1.18c and above, the available transceiver types are:
113 0 transceiver type from EEPROM config (normally 10baseT); force half-duplex
118 8 transceiver type and duplex mode taken from card's EEPROM config settings
122 Prior to driver version 1.18c, only transceiver codes 0-4 were supported. Note
123 that the new transceiver codes 8 and 12 are the *only* ones that will enable
130 The transceiver type can be changed using 'ethtool'.
[all …]
/Linux-v6.1/Documentation/devicetree/bindings/net/can/
Dcan-transceiver.yaml4 $id: http://devicetree.org/schemas/net/can/can-transceiver.yaml#
7 title: CAN transceiver Bindings
9 description: CAN transceiver generic properties bindings
/Linux-v6.1/arch/arm/mach-pxa/
Dpxa27x-udc.h62 #define UDCOTGICR_IEXR (1 << 17) /* Extra Transceiver Interrupt
64 #define UDCOTGICR_IEXF (1 << 16) /* Extra Transceiver Interrupt
92 #define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */
93 #define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */
94 #define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */
95 #define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */
96 #define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */
97 #define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */
98 #define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */
99 #define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */
[all …]
/Linux-v6.1/drivers/phy/
Dphy-can-transceiver.c3 * phy-can-transceiver.c - phy driver for CAN transceivers
123 dev_err(dev, "failed to create can transceiver phy\n"); in can_transceiver_phy_probe()
129 dev_warn(dev, "Invalid value for transceiver max bitrate. Ignoring bitrate limit\n"); in can_transceiver_phy_probe()
158 .name = "can-transceiver-phy",
167 MODULE_DESCRIPTION("CAN TRANSCEIVER PHY driver");
/Linux-v6.1/drivers/phy/ti/
DKconfig71 Enable this to support the transceiver that is part of SOC. This
95 tristate "TWL4030 USB Transceiver Driver"
102 Enable this to support the USB OTG transceiver on TWL4030
104 This transceiver supports high and full speed devices plus,
/Linux-v6.1/drivers/phy/allwinner/
DKconfig16 Enable this to support the transceiver that is part of Allwinner
44 Enable this to support the transceiver that is part of Allwinner
56 Enable this to support the USB3.0-capable transceiver that is
/Linux-v6.1/drivers/net/ethernet/dec/tulip/
Dtimer.c45 Assume this a generic MII or SYM transceiver. */ in tulip_media_task()
57 /* Type 0 serial or 4 SYM transceiver. Check the link beat bit. */ in tulip_media_task()
62 netdev_dbg(dev, "Transceiver monitor tick CSR12=%#02x, no media sense\n", in tulip_media_task()
71 netdev_dbg(dev, "Transceiver monitor tick: CSR12=%#02x bit %d is %d, expecting %d\n", in tulip_media_task()
98 netdev_dbg(dev, "No link beat on media %s, trying transceiver type %s\n", in tulip_media_task()

12345678910>>...16