| /Linux-v6.1/Documentation/power/ |
| D | pm_qos_interface.rst | 92 state latency tolerance (in microseconds) and the third one is for PM QoS flags.
95 The target values of resume latency and active state latency tolerance are
181 Active state latency tolerance
190 If there is a latency tolerance control mechanism for a given device available
196 Whenever the effective latency tolerance changes for the device, its
199 latency tolerance requirements for the device is empty, the callback is expected
200 to switch the underlying hardware latency tolerance control mechanism to an
204 automatically updating the device's latency tolerance in response to its power
206 be done in the autonomous latency tolerance control mode.
210 Then, user space can use that attribute to specify its latency tolerance
[all …]
|
| /Linux-v6.1/tools/testing/selftests/vm/ |
| D | hugetlb_reparenting_test.sh | 72 local tolerance=$((5 * 1024 * 1024))
76 if [[ $actual_a -lt $(($expected_a - $tolerance)) ]] ||
77 [[ $actual_a -gt $(($expected_a + $tolerance)) ]]; then
88 if [[ $actual_a_hugetlb -lt $(($expected_a_hugetlb - $tolerance)) ]] ||
89 [[ $actual_a_hugetlb -gt $(($expected_a_hugetlb + $tolerance)) ]]; then
104 if [[ $actual_b -lt $(($expected_b - $tolerance)) ]] ||
105 [[ $actual_b -gt $(($expected_b + $tolerance)) ]]; then
116 if [[ $actual_b_hugetlb -lt $(($expected_b_hugetlb - $tolerance)) ]] ||
117 [[ $actual_b_hugetlb -gt $(($expected_b_hugetlb + $tolerance)) ]]; then
|
| /Linux-v6.1/drivers/media/rc/img-ir/ |
| D | img-ir-hw.c | 166 * @tolerance: Tolerance as a fraction of 128 (roughly percent).
171 * tolerance, and shifts for the register, rounding in the right direction.
176 unsigned int tolerance, in img_ir_timing_range_convert() argument
182 /* add a tolerance */ in img_ir_timing_range_convert()
183 min = min - (min*tolerance >> 7); in img_ir_timing_range_convert()
184 max = max + (max*tolerance >> 7); in img_ir_timing_range_convert()
196 * @tolerance: Timing tolerance where 0-128 represents 0-100%
204 unsigned int tolerance, in img_ir_symbol_timing() argument
214 tolerance, clock_hz, pd_shift); in img_ir_symbol_timing()
216 tolerance, clock_hz, w_shift); in img_ir_symbol_timing()
[all …]
|
| D | img-ir-hw.h | 57 * and is taken care of by the tolerance)
148 * @tolerance: Timing tolerance as a percentage (default 10%).
167 unsigned int tolerance; member
|
| /Linux-v6.1/Documentation/hwmon/ |
| D | w83792d.rst | 145 via thermal_cruise# file. The tolerance# file serves to create T +- tolerance
147 remains below the thermal_cruise# +- tolerance# value. Once the temperature
148 exceeds the high limit (T+tolerance), the fan will be turned on with a
156 limit (T-tolerance), the fan speed will be fixed at the current speed because
168 temperature region (sf2_point@_fan# +- tolerance#) it will cause fans to run
194 tolerance[1-3]
|
| D | nct6775.rst | 186 Temperature step tolerance.
198 Target temperature tolerance, unit millidegree Celsius
234 Target speed tolerance
258 Temperature tolerance, unit millidegree Celsius
261 Temperature tolerance for critical temperature,
|
| D | w83793.rst | 89 predefined value, within a tolerance margin. So if tempX_input >
92 the PWM value. If the temperature is within the tolerance range, the PWM
|
| /Linux-v6.1/Documentation/misc-devices/ |
| D | ad525x_dpot.rst | 9 settings. Access to the factory programmed tolerance is also provided, but
16 Each dpot device will have a set of eeprom, rdac, and tolerance files. How
23 The tolerance files are the read-only factory programmed tolerance settings
|
| /Linux-v6.1/drivers/net/wireless/ath/ |
| D | dfs_pri_detector.c | 41 * pde_get_multiple() - get number of multiples considering a given tolerance
42 * Return value: factor if abs(val - factor*fraction) <= tolerance, 0 otherwise
44 static u32 pde_get_multiple(u32 val, u32 fraction, u32 tolerance) in pde_get_multiple() argument
55 if (delta <= tolerance) in pde_get_multiple()
56 /* val and fraction are within tolerance */ in pde_get_multiple()
61 if (remainder > tolerance) { in pde_get_multiple()
63 if ((fraction - remainder) <= tolerance) in pde_get_multiple()
64 /* remainder is within tolerance */ in pde_get_multiple()
|
| D | dfs_pattern_detector.h | 63 * @pri_min: minimum pulse repetition interval in [us] (including tolerance)
64 * @pri_max: minimum pri in [us] (including tolerance)
68 * @max_pri_tolerance: pulse time stamp tolerance on both sides [us]
|
| /Linux-v6.1/Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra20-hsuart.txt | 36 Baud Rate tolerance:
37 Standard UART devices are expected to have tolerance for baud rate error by
39 Tegra186 chip has a known hardware issue. UART Rx baud rate tolerance level
|
| /Linux-v6.1/tools/testing/selftests/kvm/x86_64/ |
| D | vmx_nested_tsc_scaling_test.c | 39 uint64_t tolerance, thresh_low, thresh_high; in compare_tsc_freq() local
41 tolerance = expected / 100; in compare_tsc_freq()
42 thresh_low = expected - tolerance; in compare_tsc_freq()
43 thresh_high = expected + tolerance; in compare_tsc_freq()
|
| D | hyperv_clock.c | 75 /* 1% tolerance */ in check_tsc_msr_rdtsc()
92 /* 10 ms tolerance */ in check_tsc_msr_tsc_page()
200 /* 1% tolerance */ in host_check_tsc_msr_rdtsc()
|
| /Linux-v6.1/net/tipc/ |
| D | bearer.h | 95 * @tolerance: default time (in ms) before declaring link failure
122 u32 tolerance; member
144 * @tolerance: default link tolerance for bearer
168 u32 tolerance; member
|
| D | link.c | 92 * @tolerance: minimum link continuity loss needed to reset link [in ms]
164 u32 tolerance; member
270 int tolerance, int priority,
362 return l->tolerance; in tipc_link_tolerance()
479 * @tolerance: link tolerance to be used by link
499 int tolerance, char net_plane, u32 mtu, int priority, in tipc_link_create() argument
537 l->tolerance = tolerance; in tipc_link_create()
539 bc_rcvlink->tolerance = tolerance; in tipc_link_create()
1232 msecs_to_jiffies(r->tolerance * 10))) in link_retransmit_failure()
1858 int tolerance, int priority, in tipc_link_build_proto_msg() argument
[all …]
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | am335x-nano.dts | 415 /* +1.5V voltage with ±4% tolerance */
423 /* VDD_MPU voltage limits 0.95V - 1.1V with ±4% tolerance */
432 /* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */
441 /* +1.8V voltage with ±4% tolerance */
449 /* +3.3V voltage with ±4% tolerance */
457 /* +1.8V voltage with ±4% tolerance */
465 /* +3.3V voltage with ±4% tolerance */
|
| D | am335x-moxa-uc-8100-me-t.dts | 83 /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
92 /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
|
| D | am335x-osd335x-common.dtsi | 77 /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
86 /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
|
| /Linux-v6.1/Documentation/devicetree/bindings/cpufreq/ |
| D | cpufreq-dt.txt | 19 - voltage-tolerance: Specify the CPU voltage tolerance in percentage.
|
| /Linux-v6.1/Documentation/ABI/removed/ |
| D | sysfs-mce | 14 Tolerance level. When a machine check exception occurs for a
20 defies normal kernel locking rules. The tolerance level
|
| /Linux-v6.1/drivers/base/power/ |
| D | qos.c | 883 * dev_pm_qos_get_user_latency_tolerance - Get user space latency tolerance.
884 * @dev: Device to obtain the user space latency tolerance for.
900 * dev_pm_qos_update_user_latency_tolerance - Update user space latency tolerance.
901 * @dev: Device to update the user space latency tolerance for.
902 * @val: New user space latency tolerance for @dev (negative values disable).
948 * dev_pm_qos_expose_latency_tolerance - Expose latency tolerance to userspace
949 * @dev: Device whose latency tolerance to expose
967 * dev_pm_qos_hide_latency_tolerance - Hide latency tolerance from userspace
968 * @dev: Device whose latency tolerance to hide
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/dce/ |
| D | dce_clock_source.c | 178 * checking for tolerance.
183 * @tolerance: Tolerance for Calculated Pixel Clock to be within
187 * if calculated values are within required tolerance
188 * It returns - true if error is within tolerance
189 * - false if error is not within tolerance
196 uint32_t tolerance) in calc_fb_divider_checking_tolerance() argument
231 if (abs_err <= tolerance) { in calc_fb_divider_checking_tolerance()
258 uint32_t tolerance; in calc_pll_dividers_in_range() local
262 tolerance = (pll_settings->adjusted_pix_clk_100hz * err_tolerance) / in calc_pll_dividers_in_range()
264 if (tolerance < CALC_PLL_CLK_SRC_ERR_TOLERANCE) in calc_pll_dividers_in_range()
[all …]
|
| /Linux-v6.1/include/uapi/linux/ |
| D | timex.h | 74 __kernel_long_t tolerance;/* clock frequency tolerance (ppm) member
113 long long tolerance;/* clock frequency tolerance (ppm) member
|
| /Linux-v6.1/drivers/staging/media/imx/ |
| D | imx-media-fim.c | 37 #define FIM_CL_TOLERANCE_MAX_DEF 0 /* no max tolerance (unbounded) */
116 /* disable tolerance range if max <= min */ in reset_fim()
163 "FIM: %llu ignored, out of tolerance bounds\n", in frame_interval_monitor()
317 .name = "FIM Tolerance Min",
327 .name = "FIM Tolerance Max",
|
| /Linux-v6.1/drivers/gpu/drm/sun4i/ |
| D | sun4i_rgb.c | 55 * VESA DMT defines a tolerance of 0.5% on the pixel clock, while the
56 * CVT spec reuses that tolerance in its examples, so it looks to be a
57 * good default tolerance for the EDID-based modes. Define it to 5 per
|
