Home
last modified time | relevance | path

Searched full:thermistors (Results 1 – 20 of 20) sorted by relevance

/Linux-v6.1/Documentation/hwmon/
Dntc_thermistor.rst4 Supported thermistors from Murata:
6 * Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473,
14 Supported thermistors from EPCOS:
16 * EPCOS NTC Thermistors B57330V2103
22 Other NTC thermistors can be supported simply by adding compensation
Dpc87360.rst134 thermistors (as opposed to thermal diodes for the first three temperature
146 thermal diode, and thermistors).
Dmax6697.rst77 thermal transistors plus three thermistors in addition to the local temperature
Dw83793.rst61 Temp5-6 can be connected to external thermistors (value of
Dit87.rst346 If a temperature sensor is configured for thermistors, the attribute values
Dvt1211.rst152 Temp3-temp7 support NTC thermistors. For these channels, the driver returns
Dsysfs-interface.rst303 Some chips measure temperature using external thermistors and an ADC, and
/Linux-v6.1/arch/arm/boot/dts/
Dcros-adc-thermistors.dtsi3 * Thermistor dts fragment for devices that use Thermistors as
Dste-hrefv60plus.dtsi50 * Thermistors on the board, formally to monitor battery temperatures
Dexynos5420-peach-pit.dts1122 #include "cros-adc-thermistors.dtsi"
Dexynos5800-peach-pi.dts1104 #include "cros-adc-thermistors.dtsi"
/Linux-v6.1/Documentation/devicetree/bindings/iio/temperature/
Dadi,ltc2983.yaml293 resistor is used for multiple thermistors. Note that this property
316 and uK only for custom thermistors. For more details look at table
360 Rsense are used by thermistors and RTD's.
/Linux-v6.1/Documentation/devicetree/bindings/thermal/
Dthermal-generic-adc.txt3 On some of platforms, thermal sensor like thermistors are connected to
/Linux-v6.1/Documentation/devicetree/bindings/hwmon/
Dntc-thermistor.yaml13 Thermistors with negative temperature coefficient (NTC) are resistors that
/Linux-v6.1/drivers/hwmon/
Dntc_thermistor.c3 * ntc_thermistor.c - NTC Thermistors
70 * Thermistors Datasheet
221 * Thermistors Datasheets
Dpc87360.c675 * used in the chip to measure voltage across the thermistors
1335 dev_dbg(&pdev->dev, "bios thermistors:%d\n", use_thermistors); in pc87360_init_device()
1340 /* thermistors are temp[4-6], measured on vin[11-14] */ in pc87360_init_device()
1343 dev_dbg(&pdev->dev, "using thermistors:%d\n", use_thermistors); in pc87360_init_device()
1676 /* Are we using thermistors? */ in pc87360_find()
1687 pr_info("Using thermistors for temperature monitoring\n"); in pc87360_find()
DKconfig1474 This driver supports NTC thermistors sensor reading and its
/Linux-v6.1/drivers/iio/adc/
DKconfig893 power, on board system thermistors connected to the PMIC ADC,
896 hardware supports internal pull-up for thermistors and can choose between
Dqcom-pm8xxx-xoadc.c169 * thermistors are connected or other hardware characteristics are
/Linux-v6.1/drivers/mfd/
Dtc6393xb.c544 /* BAT1 and BAT0 thermistors appear to be swapped */