Searched full:sw4 (Results 1 – 25 of 80) sorted by relevance
1234
| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | ltc3676.txt | 8 - regulators: Contains eight regulator child nodes sw1, sw2, sw3, sw4,
13 nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify
20 Regulators sw1, sw2, sw3, sw4 can regulate the feedback reference from:
63 sw4_reg: sw4 {
|
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
104 SW4 {
105 regulator-name = "sw4";
|
| D | pfuze100.yaml | 15 sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6
136 sw4_reg: sw4 {
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | imx28-eukrea-mbmx28lc.dtsi | 40 switch-sw4 {
41 label = "SW4";
202 gpio_button_sw4_pins_mbmx28lc: gpio-button-sw4-mbmx28lc@0 {
|
| D | imx6q-bosch-acc.dts | 213 reg_sw4: regulator-sw4 {
332 sw4_reg: sw4 {
333 regulator-name = "AUX 3V15 (sw4)";
|
| D | pm9g45.dts | 174 label = "SW4";
|
| D | sun8i-h3-orangepi-lite.dts | 94 label = "sw4";
|
| D | imx6qdl-wandboard-revd1.dtsi | 73 sw4_reg: sw4 {
|
| D | imx6sx-sdb-reva.dts | 60 sw4_reg: sw4 {
|
| D | imx6qdl-tqma6.dtsi | 135 sw4_reg: sw4 {
|
| D | sun8i-h3-orangepi-2.dts | 101 label = "sw4";
|
| D | sun8i-h3-orangepi-one.dts | 93 label = "sw4";
|
| D | sun8i-h3-orangepi-pc.dts | 93 label = "sw4";
|
| /Linux-v6.1/arch/arm64/boot/dts/allwinner/ |
| D | sun50i-h5-orangepi-prime.dts | 54 key-sw4 {
55 label = "sw4";
|
| D | sun50i-h5-orangepi-pc2.dts | 60 key-sw4 {
61 label = "sw4";
|
| /Linux-v6.1/Documentation/devicetree/bindings/mfd/ |
| D | mc13xxx.txt | 89 sw4 : regulator SW4 (register 27, bit 0)
|
| /Linux-v6.1/drivers/regulator/ |
| D | ltc3676.c | 172 /* SW1, SW2, SW3, SW4 linear 0.8V-3.3V with scalar via R1/R2 feeback res */
228 LTC3676_LINEAR_REG(SW4, sw4, BUCK4, DVB4A),
|
| D | cpcap-regulator.c | 326 * SW1 to SW4 and SW6 seems to be unused for mapphone. Note that VSIM and
339 CPCAP_REG(SW4, CPCAP_REG_S4C1, CPCAP_REG_ASSIGN2,
415 CPCAP_REG(SW4, CPCAP_REG_S4C1, CPCAP_REG_ASSIGN2,
|
| D | pfuze100-regulator.c | 376 PFUZE100_SW_REG(PFUZE100, SW4, PFUZE100_SW4VOL, 400000, 1975000, 25000),
442 { .name = "sw4", },
784 /* SW2~SW4 high bit check and modify the voltage value table */ in pfuze100_regulator_probe()
|
| /Linux-v6.1/arch/arm64/boot/dts/renesas/ |
| D | ebisu.dtsi | 99 label = "SW4-1";
106 label = "SW4-2";
113 label = "SW4-3";
120 label = "SW4-4";
|
| D | rzg2l-smarc.dtsi | 44 * SW4 should be at position 2->3 so that SER0_RTS# line is activated
|
| D | salvator-common.dtsi | 133 label = "SW4-1";
140 label = "SW4-2";
147 label = "SW4-3";
154 label = "SW4-4";
|
| D | rzg2lc-smarc.dtsi | 86 * SW4 should be at position 2->3 so that SER0_RTS# line is activated
|
| /Linux-v6.1/arch/arm64/boot/dts/freescale/ |
| D | imx8mq-sr-som.dtsi | 72 sw4_reg: sw4 {
|
| /Linux-v6.1/arch/arm64/boot/dts/rockchip/ |
| D | rk3326-odroid-go2.dts | 85 * | sw3 sw4 | | sw7 sw5 |
108 button-sw4 {
|
1234
