| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | ltc3676.txt | 8 - regulators: Contains eight regulator child nodes sw1, sw2, sw3, sw4,
13 nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify
20 Regulators sw1, sw2, sw3, sw4 can regulate the feedback reference from:
54 sw3_reg: sw3 {
|
| D | ltc3589.txt | 8 - regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out,
13 nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify
20 Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from
54 sw3_reg: sw3 {
|
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
97 SW3 {
98 regulator-name = "sw3";
|
| D | pfuze100.yaml | 19 sw1a,sw1b,sw2,sw3,swbst,vsnvs,vrefddr,vldo1,vldo2,vccsd,v33,vldo3,vldo4
21 sw1,sw2,sw3,vsnvs,vldo1,vldo2,vccsd,v33,vldo3,vldo4
|
| /Linux-v6.1/Documentation/devicetree/bindings/mfd/ |
| D | mc13xxx.txt | 59 sw3 : regulator SW3 (register 29, bit 20)
88 sw3 : regulator SW3 (register 26, bit 0)
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | imx53-qsrb.dts | 58 sw3_reg: sw3 {
59 regulator-name = "SW3";
|
| D | imx28-eukrea-mbmx28lc.dtsi | 27 switch-sw3 {
28 label = "SW3";
192 gpio_button_sw3_pins_mbmx28lc: gpio-button-sw3-mbmx28lc@0 {
|
| D | armada-388-clearfog-base.dts | 23 /* The rear SW3 button */
|
| D | pm9g45.dts | 180 label = "SW3";
|
| D | armada-388-clearfog.dts | 39 /* The rear SW3 button */
|
| D | imx6ul-tqma6ul-common.dtsi | 57 reg_sw3_ddr: sw3 {
|
| D | at91-kizbox3-hs.dts | 86 label = "SW3";
|
| D | imx53-usbarmory.dts | 168 sw3_reg: sw3 {
|
| /Linux-v6.1/Documentation/hid/ |
| D | hid-alps.rst | 114 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
164 Byte1 1 1 1 0 1 SW3 SW2 SW1
173 SW1-SW3:
|
| /Linux-v6.1/drivers/hid/ |
| D | hid-ite.c | 31 /* For Acer Aspire Switch 10E (SW3-016) keyboard-dock */ in ite_report_fixup()
33 hid_info(hdev, "Fixing up Acer Aspire Switch 10E (SW3-016) ITE keyboard report descriptor\n"); in ite_report_fixup()
|
| /Linux-v6.1/drivers/media/dvb-frontends/ |
| D | dib0090.h | 87 extern int dib0090_set_switch(struct dvb_frontend *fe, u8 sw1, u8 sw2, u8 sw3);
157 u8 sw1, u8 sw2, u8 sw3) in dib0090_set_switch() argument
|
| /Linux-v6.1/drivers/regulator/ |
| D | ltc3676.c | 172 /* SW1, SW2, SW3, SW4 linear 0.8V-3.3V with scalar via R1/R2 feeback res */
227 LTC3676_LINEAR_REG(SW3, sw3, BUCK3, DVB3A),
|
| D | ltc3589.c | 131 /* SW1, SW2, SW3, LDO2 */
259 LTC3589_LINEAR_REG(SW3, sw3, B3DTV1),
|
| D | pcap-regulator.c | 133 /* SW3 STBY is on PCAP_REG_AUXVREG */
134 VREG_INFO(SW3, PCAP_REG_SWCTRL, 11, 12, 24, NA),
|
| D | pfuze100-regulator.c | 410 PFUZE3000_SW3_REG(PFUZE3000, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
425 PFUZE3000_SW3_REG(PFUZE3001, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
480 { .name = "sw3", },
497 { .name = "sw3", },
|
| D | mc13783-regulator.c | 253 MC13783_DEFINE_SW(SW3, sw3, SWITCHERS5, SWITCHERS5, mc13783_sw3_val),
|
| /Linux-v6.1/arch/arm64/boot/dts/renesas/ |
| D | rzg2l-smarc.dtsi | 43 * SW3 should be at position 2->3 so that SER0_RX line is activated
|
| D | rzg2lc-smarc.dtsi | 85 * SW3 should be at position 2->3 so that SER0_RX line is activated
|
| /Linux-v6.1/arch/sh/boards/mach-rsk/ |
| D | devices-rsk7203.c | 101 .desc = "SW3",
|
| /Linux-v6.1/Documentation/networking/ |
| D | arcnet-hardware.rst | 832 SW3 1-8: Node ID Select
848 The eight switches in group SW3 are used to set the node ID. Each node
1998 SW3 1-5: IRQ Select
2008 The eight switches in SW3 are used to set the node ID. Each node attached
2072 *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON.
2080 Switches 1-5 of the switch block SW3 control the IRQ level::
2095 The switches 6-7 of the switch block SW3 are used to determine the timeout
2851 | SW3 | || | |
2870 SW3 1-5: IRQ Select
2876 Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not
[all …]
|
