| /Linux-v6.1/net/mac80211/ |
| D | scan.c | 3 * Scanning implementation
288 if (test_and_clear_bit(SCAN_BEACON_WAIT, &local->scanning)) { in ieee80211_scan_rx()
290 * we were passive scanning because of radar/no-IR, but in ieee80211_scan_rx()
294 set_bit(SCAN_BEACON_DONE, &local->scanning); in ieee80211_scan_rx()
313 * unless scanning with randomised address in ieee80211_scan_rx()
366 if (test_bit(SCAN_HW_CANCELLED, &local->scanning)) in ieee80211_prep_hw_scan()
423 bool hw_scan = test_bit(SCAN_HW_SCANNING, &local->scanning); in __ieee80211_scan_completed()
424 bool was_scanning = local->scanning; in __ieee80211_scan_completed()
437 if (WARN_ON(!local->scanning && !aborted)) in __ieee80211_scan_completed()
475 local->scanning = 0; in __ieee80211_scan_completed()
[all …]
|
| /Linux-v6.1/Documentation/dev-tools/ |
| D | kmemleak.rst | 41 Memory scanning parameters can be modified at run-time by writing to the
47 enable the task stacks scanning (default)
49 disable the tasks stacks scanning
51 start the automatic memory scanning thread (default)
53 stop the automatic memory scanning thread
55 set the automatic memory scanning period in seconds
56 (default 600, 0 to stop the automatic scanning)
92 scanning the memory (including saved registers). This means that there
97 The scanning algorithm steps:
183 reported by kmemleak because values found during the memory scanning
[all …]
|
| /Linux-v6.1/fs/ubifs/ |
| D | scan.c | 55 * This function returns a scanning code to indicate what was scanned.
76 dbg_scan("scanning %s at LEB %d:%d", in ubifs_scan_a_node()
116 * ubifs_start_scan - create LEB scanning information at start of scan.
157 * ubifs_end_scan - update LEB scanning information at end of scan.
159 * @sleb: scanning information
166 dbg_scan("stop scanning LEB %d at offset %d", lnum, offs); in ubifs_end_scan()
173 * ubifs_add_snod - add a scanned node to LEB scanning information.
175 * @sleb: scanning information
338 ubifs_err(c, "LEB %d scanning failed", lnum); in ubifs_scan()
345 ubifs_err(c, "LEB %d scanning failed, error %d", lnum, err); in ubifs_scan()
[all …]
|
| /Linux-v6.1/net/bluetooth/ |
| D | hci_request.c | 333 bt_dev_dbg(hdev, "Scanning is paused for suspend"); in hci_req_add_le_scan_disable()
526 * - Interleaved scanning is not currently using the allowlist in update_accept_list()
549 bt_dev_dbg(hdev, "Scanning is paused for suspend"); in hci_req_start_scan()
559 /* Use ext scanning if set ext scan param and ext scan enable is in hci_req_start_scan()
632 /* Returns true if an le connection is in the scanning state */
690 * scanning and non-connectable advertising. in hci_update_random_address()
755 /* Background scanning should run with address resolution */ in hci_req_add_le_passive_scan()
759 bt_dev_dbg(hdev, "Scanning is paused for suspend"); in hci_req_add_le_passive_scan()
764 * during passive scanning. Not using an non-resolvable address in hci_req_add_le_passive_scan()
779 * happen before enabling scanning. The controller does in hci_req_add_le_passive_scan()
[all …]
|
| D | hci_sync.c | 400 /* If controller is not scanning we are done. */ in hci_le_scan_restart_sync()
405 bt_dev_dbg(hdev, "Scanning is paused for suspend"); in hci_le_scan_restart_sync()
903 * scanning and non-connectable advertising. in hci_update_random_address_sync()
2002 /* If controller is not scanning we are done. */ in hci_scan_disable_sync()
2007 bt_dev_dbg(hdev, "Scanning is paused for suspend"); in hci_scan_disable_sync()
2013 bt_dev_err(hdev, "Unable to disable scanning: %d", err); in hci_scan_disable_sync()
2379 /* Device must not be scanning when updating the accept list.
2389 * Enable Scanning
2484 * - Interleaved scanning is not currently using the allowlist in hci_update_accept_list_sync()
2507 /* Returns true if an le connection is in the scanning state */
[all …]
|
| /Linux-v6.1/mm/ |
| D | kmemleak.c | 30 * (atomic or kmemleak_lock). This lock is also held when scanning the
33 * lock like kmemleak_lock during scanning.
37 * scanned. This list is only modified during a scanning episode when the
42 * modifications to the memory scanning parameters including the scan_thread
112 #define SECS_SCAN_WAIT 600 /* subsequent auto scanning delay */
123 /* scanning area inside a memory block */
230 /* enables or disables the task stacks scanning */
232 /* protects the memory scanning, parameters and debug/kmemleak file access */
841 * Add a scanning area to the object. If at least one such area is added,
867 pr_warn_once("Cannot allocate a scan area, scanning the full object\n"); in add_scan_area()
[all …]
|
| D | vmpressure.c | 64 * critical level when scanning depth is ~10% of the lru size (vmscan
266 * current scanning depth. But it does not mean that we should in vmpressure()
267 * report the critical pressure, yet. If the scanning priority in vmpressure()
268 * (scanning depth) goes too high (deep), we will be notified in vmpressure()
323 * the vmscan's reclaiming priority (scanning depth) changes.
|
| /Linux-v6.1/drivers/mtd/nand/onenand/ |
| D | onenand_bbt.c | 46 * create_bbt - [GENERIC] Create a bad block table by scanning the device
53 * Create a bad block table by scanning the device
67 printk(KERN_INFO "Scanning device for bad blocks\n"); in create_bbt()
128 * The function creates a memory based bbt by scanning the device
211 * while scanning a device for factory marked good / bad blocks.
|
| /Linux-v6.1/Documentation/ABI/stable/ |
| D | sysfs-bus-w1 | 4 Description: Bus scanning interval, microseconds component.
11 Users: any user space application which wants to know bus scanning
|
| /Linux-v6.1/arch/sh/boards/ |
| D | of-generic.c | 60 pr_info("SH generic board support: scanning for cpus\n"); in sh_of_smp_probe()
139 pr_info("SH generic board support: scanning for interrupt controllers\n"); in sh_of_init_irq()
147 pr_info("SH generic board support: scanning for clk providers\n"); in sh_of_clk_init()
|
| /Linux-v6.1/Documentation/devicetree/bindings/input/touchscreen/ |
| D | cypress,cy8ctma340.yaml | 88 scanning/processing cycles when the chip is in active mode
94 scanning/processing cycles when the chip is in low-power mode
108 every scanning/processing cycle)
|
| /Linux-v6.1/Documentation/scsi/ |
| D | advansys.rst | 178 This option can be used to either disable I/O port scanning or to limit
179 scanning to 1 - 4 I/O ports. Regardless of the option setting EISA and
184 1. Eliminate I/O port scanning:
194 2. Limit I/O port scanning to one I/O port:
200 3. Limit I/O port scanning to four I/O ports:
|
| /Linux-v6.1/drivers/staging/r8188eu/include/ |
| D | rtw_led.h | 27 LED_BLINK_SCAN = 6, /* LED is blinking during scanning period,
29 * for scanning. */
|
| /Linux-v6.1/Documentation/ABI/testing/ |
| D | sysfs-class-uwb_rc | 68 to start (or stop) scanning on a channel. <type> is one of:
74 3 scanning disabled
86 not beaconing or scanning.
|
| /Linux-v6.1/drivers/net/wireless/realtek/rtlwifi/btcoexist/ |
| D | rtl_btc.h | 32 bool scanning);
34 bool scanning);
|
| /Linux-v6.1/Documentation/scheduler/ |
| D | sched-debug.rst | 43 tasks virtual memory. It effectively controls the maximum scanning
50 tasks virtual memory. It effectively controls the minimum scanning
|
| /Linux-v6.1/drivers/scsi/ |
| D | scsi_scan.c | 8 * The general scanning/probing algorithm is as follows, exceptions are
54 " SCSI scanning, some SCSI devices might not be configured\n"
69 * Return values of some of the scanning functions.
105 "Setting to 'manual' disables automatic scanning, but allows "
144 * When this function returns, any host which started scanning before
146 * started scanning after this function was called may or may not have
820 * The scanning code needs to know the scsi_level, even if no in scsi_probe_lun()
870 * scanning run at their own risk, or supply a user level program in scsi_add_lun()
1325 * If less than SCSI_1_CCS, and no special lun scanning, stop in scsi_sequential_lun_scan()
1326 * scanning; this matches 2.4 behaviour, but could just be a bug in scsi_sequential_lun_scan()
[all …]
|
| /Linux-v6.1/Documentation/driver-api/80211/ |
| D | cfg80211.rst | 96 Scanning and BSS list handling
100 :doc: Scanning and BSS list handling
|
| /Linux-v6.1/drivers/gpu/drm/msm/disp/mdp5/ |
| D | mdp5_smp.h | 41 * assigned to pipes that are still scanning out
44 * scanning out.
|
| /Linux-v6.1/include/linux/ |
| D | of_fdt.h | 25 /* For scanning an arbitrary device-tree at any time */
44 /* For scanning the flat device-tree at boot time */
|
| /Linux-v6.1/Documentation/userspace-api/media/v4l/ |
| D | dev-raw-vbi.rst | 136 - This is the scanning system line number associated with the first
145 identify scanning lines, VBI acquisition may not require this
160 if the scanning system is progressive, i. e. not interlaced. The
196 (lower scanning line numbers) first in memory. This may be a top
|
| /Linux-v6.1/drivers/mtd/ubi/ |
| D | Kconfig | 68 in nearly constant time. Instead of scanning the whole MTD device it
72 attaching by scanning takes long. UBI will not automatically install
|
| /Linux-v6.1/drivers/sh/maple/ |
| D | maple.c | 51 static int started, scanning, fullscan; variable
516 scanning = 1; in maple_map_subunits()
580 if (!started || (scanning == 2) || !fullscan) { in maple_response_devinfo()
698 /* if scanning is 1 then we have subdevices to check */ in maple_dma_handler()
699 if (scanning == 1) { in maple_dma_handler()
701 scanning = 2; in maple_dma_handler()
703 scanning = 0; in maple_dma_handler()
|
| /Linux-v6.1/arch/x86/kernel/ |
| D | check.c | 136 pr_info("Scanning %d areas for low memory corruption\n", num_scan_areas); in setup_bios_corruption_check()
179 pr_info("Scanning for low memory corruption every %d seconds\n", corruption_check_period); in start_periodic_check_for_corruption()
|
| /Linux-v6.1/Documentation/driver-api/acpi/ |
| D | scan_handlers.rst | 26 The core ACPI namespace scanning code in drivers/acpi/scan.c carries out basic
54 The namespace scanning function, acpi_bus_scan(), first registers all of the
|
