Searched full:safety (Results 1 – 25 of 298) sorted by relevance
12345678910>>...12
95 mov r0, r0 @ safety96 mov r0, r0 @ safety97 mov r0, r0 @ safety99 mov r0, r0 @ safety100 mov r0, r0 @ safety101 mov r0, r0 @ safety
79 description: Eye safety function pulse width limit in microsecond.85 description: Eye safety function load current limit in microamp.117 description: Eye safety function enable control.
46 Description: Maximum charge current; May be clamped to safety limits.60 voltage. May be clamped to safety limits.106 the JEITA safety guidelines if this flag is set.
18 Specifies the charger's PRECONDITION safety timer setting value;22 Specifies the charger's total safety timer setting value;
15 * most of the compressed data. There must be enough safety margin to18 * The safety margin for XZ with LZMA2 or BCJ+LZMA2 is calculated below.48 * safety margin for LZMA2.73 * Now we have enough information to calculate the safety margin. We need
8 * most of the compressed data. There must be enough safety margin to11 * The safety margin for ZSTD with a 128 KB block size is calculated below.42 * Now we have enough information to calculate the safety margin. We need
45 0x5 0x0 0xe0400000 0x00010000 /* CS5: safety */125 safety@5,0 {126 compatible = "ifm,safety";
26 #define KTD253_T_LOW_NS (200 + 10) /* Additional 10ns as safety factor */27 #define KTD253_T_HIGH_NS (200 + 10) /* Additional 10ns as safety factor */
31 unsigned long safety; member
49 unsigned long safety; member
59 * Min HPET period is 10^5 femto sec just for safety. If it is less than this,
61 * individually. For maximum safety, don't enable any assumptions!63 * For minimal code size and no safety, use ASSUME_PERFECT at your own risk.
16 CPU/SOC, for thermal safety reasons.
32 * This provides SMP safety on the p1275buf.
8 Safety section in Regulator API design notes
17 generated can be routed to either interrupt a safety controller or
38 relying on this code in a safety critical system!
187 /* Safety Feature statistics exposed by ethtool */194 /* Number of fields in Safety Stats */365 /* Automotive Safety Package */
193 /* 1. Enable Safety Features */ in dwmac5_safety_feat_config()202 /* 2. Enable MTL Safety Interrupts */ in dwmac5_safety_feat_config()210 /* 3. Enable DMA Safety Interrupts */ in dwmac5_safety_feat_config()231 * All the Automotive Safety features are selected without the "Parity in dwmac5_safety_feat_config()
61 * Min HPET period is 10^5 femto sec just for safety. If it is less than this,
16 * out the condition into a nop. DO_ONCE() guarantees type safety of
20 * architecture) provided ~40% safety margin on stack usage while keeping
232 * @safety_timer: charging safety timer280 * abx500_chargalg_safety_timer_expired() - Expiration of the safety timer283 * This function gets called when the safety timer for the charger291 dev_err(di->dev, "Safety timer expired\n"); in abx500_chargalg_safety_timer_expired()429 * abx500_chargalg_start_safety_timer() - Start charging safety timer432 * The safety timer is used to avoid overcharging of old or bad batteries.462 * abx500_chargalg_stop_safety_timer() - Stop charging safety timer465 * The safety timer is stopped whenever the NORMAL state is exited1330 /* Safety timer expiration */ in abx500_chargalg_algorithm()2022 /* Initilialize safety timer */ in abx500_chargalg_probe()
232 * @main_safety_tmr_h safety timer for main charger233 * @usb_safety_tmr_h safety timer for usb charger
337 int safety = 0; in saa7164_cmd_send() local445 if (safety++ > 16) { in saa7164_cmd_send()447 "dequeue exceeded, safety exit\n"); in saa7164_cmd_send()
