Searched full:reconfigure (Results 1 – 25 of 309) sorted by relevance
12345678910>>...13
| /Linux-v6.1/include/linux/phy/ |
| D | phy-dp.h | 69 * Flag indicating, whether or not reconfigure link rate and SSC to
78 * Flag indicating, whether or not reconfigure lane count to
87 * Flag indicating, whether or not reconfigure voltage swing
|
| /Linux-v6.1/drivers/net/ethernet/netronome/nfp/ |
| D | nfp_net_common.c | 181 * @nn: NFP Net device to reconfigure
249 * __nfp_net_reconfig() - Reconfigure the firmware
250 * @nn: NFP Net device to reconfigure
304 * nfp_net_mbox_reconfig() - Reconfigure the firmware via the mailbox
305 * @nn: NFP Net device to reconfigure
848 * @nn: NFP Net device to reconfigure
861 * @nn: NFP Net device to reconfigure
874 * @nn: NFP Net device to reconfigure
903 * @nn: NFP Net device to reconfigure
918 * @nn: NFP Net device to reconfigure
[all …]
|
| /Linux-v6.1/fs/autofs/ |
| D | Kconfig | 30 don't have a laptop which needs to dynamically reconfigure to the
|
| /Linux-v6.1/drivers/nvdimm/ |
| D | pfn.h | 36 * configurations mainly to allow a backup, reconfigure the
|
| /Linux-v6.1/Documentation/devicetree/bindings/power/reset/ |
| D | gpio-poweroff.yaml | 31 Initially configure the GPIO line as an input. Only reconfigure
|
| /Linux-v6.1/include/net/ |
| D | ncsi.h | 15 * package and channel while ncsi_dev_state_config helps to reconfigure
|
| /Linux-v6.1/fs/jfs/ |
| D | resize.c | 116 * reconfigure LV spaces in jfs_extendfs()
123 * reconfigure inline log space: in jfs_extendfs()
152 * reconfigure fsck work space: in jfs_extendfs()
|
| /Linux-v6.1/include/linux/ |
| D | fs_context.h | 121 int (*reconfigure)(struct fs_context *fc); member
153 vfs_get_single_reconf_super, /* As above, but reconfigure if it exists */
|
| /Linux-v6.1/Documentation/userspace-api/media/mediactl/ |
| D | request-api.rst | 12 the same pipeline to reconfigure and collaborate closely on a per-frame basis.
21 on the media pipeline, reconfigure it for the next frame, queue the buffers to
|
| /Linux-v6.1/arch/mips/bcm63xx/ |
| D | prom.c | 85 * reconfigure itself then go back to sleep. in prom_init()
|
| /Linux-v6.1/Documentation/networking/device_drivers/atm/ |
| D | fore200e.rst | 56 2. Reconfigure your kernel to set the new firmware name and location.
|
| /Linux-v6.1/fs/ |
| D | fs_context.c | 643 .reconfigure = legacy_reconfigure,
672 * from where it can be used to reconfigure a superblock.
681 * until we actually try to reconfigure.
|
| /Linux-v6.1/drivers/net/ethernet/sfc/falcon/ |
| D | mdio_10g.h | 75 /* Generic part of reconfigure: set/clear loopback bits */
|
| D | tenxpress.c | 241 /* Try and reconfigure the device */ in tenxpress_special_reset()
481 .reconfigure = tenxpress_phy_reconfigure,
|
| /Linux-v6.1/fs/vboxsf/ |
| D | super.c | 69 vbg_err("vboxsf: Cannot reconfigure nls option\n"); in vboxsf_parse_param()
431 .reconfigure = vboxsf_reconfigure,
|
| /Linux-v6.1/drivers/cpufreq/ |
| D | s3c2416-cpufreq.c | 51 * it's essential to leave dvs, as some boards do not reconfigure the
316 /* some boards don't reconfigure the regulator on reboot, which in s3c2416_cpufreq_reboot_notifier_evt()
|
| /Linux-v6.1/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-bindings.txt | 15 need to reconfigure pins at run-time, for example to tri-state pins when the
|
| /Linux-v6.1/drivers/crypto/qat/qat_common/ |
| D | adf_sysfs.c | 143 dev_info(dev, "Device qat_dev%d must be down to reconfigure the service.\n", in cfg_services_store()
|
| /Linux-v6.1/drivers/net/ethernet/stmicro/stmmac/ |
| D | dwmac-sunxi.c | 79 /* only GMII mode requires us to reconfigure the clock lines */ in sun7i_fix_speed()
|
| /Linux-v6.1/Documentation/devicetree/bindings/mmc/ |
| D | ti-omap-hsmmc.txt | 104 The workaround is to reconfigure the dat1 line as a GPIO upon suspend. To make
|
| /Linux-v6.1/Documentation/driver-api/usb/ |
| D | typec_bus.rst | 52 in need to reconfigure the pins on the connector, the alternate mode driver
|
| /Linux-v6.1/drivers/pwm/ |
| D | pwm-renesas-tpu.c | 160 * Make sure the channel is stopped, as we need to reconfigure it in tpu_pwm_timer_start()
328 * running, there's no need to reconfigure it completely, Just in tpu_pwm_config()
|
| /Linux-v6.1/Documentation/networking/device_drivers/ethernet/cirrus/ |
| D | cs89x0.rst | 459 option to reconfigure the adapter by selecting a different value for the system
536 self-test. If so, reconfigure the adapter selecting another choice for the
541 the adapter and reconfigure it by installing it in another PC to run the
|
| /Linux-v6.1/arch/mips/bmips/ |
| D | setup.c | 83 * reconfigure itself then go back to sleep. in bcm63xx_fixup_cpu1()
|
| /Linux-v6.1/Documentation/devicetree/bindings/pci/ |
| D | host-generic-pci.yaml | 72 is there any reason for the driver to reconfigure ATU windows for
|
12345678910>>...13
