Searched full:pulsing (Results 1 – 19 of 19) sorted by relevance
| /Linux-v5.10/drivers/usb/phy/ |
| D | phy-fsl-usb.c | 116 /* Charge vbus for vbus pulsing in SRP */
169 * data-line pulsing in SRP
204 /* Start SRP pulsing by data-line pulsing, followed with v-bus pulsing. */
247 * residual voltage of vbus pulsing and A device pull up in b_vbus_pulse_end()
|
| D | phy-fsl-usb.h | 271 #define TB_VBUS_PLS (30) /* time to keep vbus pulsing asserted */
|
| /Linux-v5.10/Documentation/devicetree/bindings/leds/ |
| D | ti,tca6507.yaml | 14 7 separate lines either by holding them low, or by pulsing them with modulated
|
| /Linux-v5.10/arch/arm/mach-lpc32xx/ |
| D | serial.c | 138 /* Disable IrDA pulsing support on UART6 */ in lpc32xx_serial_init()
|
| /Linux-v5.10/drivers/usb/chipidea/ |
| D | otg_fsm.c | 530 * Start SRP pulsing by data-line pulsing,
531 * no v-bus pulsing followed
|
| /Linux-v5.10/drivers/leds/ |
| D | leds-spi-byte.c | 20 * * Mode: 01 -> pulsing pattern (min -> max -> min) with an interval. From
|
| D | leds-tca6507.c | 6 * separate lines either by holding them low, or by pulsing them
|
| /Linux-v5.10/drivers/iio/dac/ |
| D | ti-dac7612.c | 141 * event can change the value of all DACs by pulsing down the LOADDACs in dac7612_probe()
|
| /Linux-v5.10/drivers/input/misc/ |
| D | powermate.c | 24 * intensity, or to a rhythmic pulsing. Several patterns and speeds are available.
261 …bits 8-16: 9 bits: pulsing speed modifier (0 ... 510); 0-254 = slower, 255 = standard, 256-510 = … in powermate_input_event()
|
| /Linux-v5.10/include/linux/usb/ |
| D | otg-fsm.h | 122 * @data_pulse: TRUE when the B-device is performing data line pulsing
|
| /Linux-v5.10/drivers/net/phy/ |
| D | intel-xway.c | 109 /* Pulsing Configuration */
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | meson8b-ec100.dts | 88 * "breathing"/pulsing effect until the power is fully
|
| /Linux-v5.10/Documentation/driver-api/ |
| D | generic-counter.rst | 156 In this example, the Signal is a source input line with a pulsing
|
| /Linux-v5.10/drivers/net/ethernet/aquantia/atlantic/ |
| D | aq_ptp.c | 371 "Enable GPIO %d pulsing, start time %llu, period %u\n", in aq_ptp_hw_pin_conf()
375 "Disable GPIO %d pulsing, start time %llu, period %u\n", in aq_ptp_hw_pin_conf()
|
| /Linux-v5.10/drivers/staging/comedi/drivers/ |
| D | s626.c | 1390 /* Start ADC by pulsing GPIO1. */ in s626_reset_adc()
1517 /* Start ADC by pulsing GPIO1 low */ in s626_ai_insn_read()
|
| /Linux-v5.10/drivers/usb/dwc2/ |
| D | core.h | 354 * @ts_dline: Enable Term Select Dline pulsing
|
| D | hcd.c | 2089 /* Set external TS Dline pulsing bit if needed */ in dwc2_core_init()
|
| /Linux-v5.10/drivers/gpu/drm/bridge/synopsys/ |
| D | dw-hdmi.c | 307 * other than pulsing the SDA line. in dw_hdmi_i2c_unwedge()
|
| /Linux-v5.10/drivers/media/pci/bt8xx/ |
| D | bttv-cards.c | 4370 * connection prior to establish a new one, pulsing the STROBE pin.
|
