Searched full:pulling (Results 1 – 25 of 94) sorted by relevance
1234
| /Linux-v5.15/Documentation/driver-api/gpio/ |
| D | drivers-on-gpio.rst | 37 the system by pulling a GPIO line and will register a restart handler so
41 system down by pulling a GPIO line and will register a pm_power_off()
70 regulator providing a certain voltage by pulling a GPIO line, integrating
|
| /Linux-v5.15/Documentation/devicetree/bindings/sound/ |
| D | everest,es7241.txt | 14 Format used by the serial interface is controlled by pulling
|
| /Linux-v5.15/arch/hexagon/kernel/ |
| D | vmlinux.lds.S | 11 #include <asm/cache.h> /* and now we're pulling cache line size */
|
| /Linux-v5.15/mm/ |
| D | page_reporting.h | 30 * threshold then it will start the process of pulling some pages and
|
| /Linux-v5.15/drivers/staging/fbtft/ |
| D | fbtft-io.c | 144 /* Start writing by pulling down /WR */ in fbtft_write_gpio8_wr()
194 /* Start writing by pulling down /WR */ in fbtft_write_gpio16_wr()
|
| /Linux-v5.15/Documentation/devicetree/bindings/input/ |
| D | cypress,tm2-touchkey.yaml | 43 e.g. for pulling up the interrupt line or the I2C pins.
|
| /Linux-v5.15/drivers/i2c/algos/ |
| D | i2c-algo-bit.c | 262 "%s: SCL unexpected low while pulling SDA low!\n", in test_bus()
276 "%s: SCL unexpected low while pulling SDA high!\n", in test_bus()
290 "%s: SDA unexpected low while pulling SCL low!\n", in test_bus()
304 "%s: SDA unexpected low while pulling SCL high!\n", in test_bus()
|
| /Linux-v5.15/net/sched/ |
| D | sch_multiq.c | 101 * pulling an skb to avoid head-of-line blocking. in multiq_dequeue()
133 * pulling an skb to avoid head-of-line blocking. in multiq_peek()
|
| /Linux-v5.15/Documentation/leds/ |
| D | leds-lm3556.rst | 24 or by pulling the STROBE pin HIGH.
|
| /Linux-v5.15/Documentation/process/ |
| D | submit-checklist.rst | 15 that facility. Don't depend on other header files pulling in ones
|
| D | maintainer-pgp-guide.rst | 736 developers to ensure that the git repository they are pulling from has
746 If you are pulling a tag from another fork of the project repository,
747 git should automatically verify the signature at the tip you're pulling
|
| /Linux-v5.15/drivers/scsi/aacraid/ |
| D | dpcsup.c | 50 * Keep pulling response QEs off the response queue and waking in aac_response_normal()
167 * Keep pulling response QEs off the response queue and waking in aac_command_normal()
|
| /Linux-v5.15/drivers/net/ethernet/microchip/sparx5/ |
| D | sparx5_mactable.c | 310 * SW is pulling again in sparx5_add_mact_entry()
340 * SW is pulling again in sparx5_del_mact_entry()
|
| /Linux-v5.15/fs/jffs2/ |
| D | background.c | 110 * This forces the GCD to slow the hell down. Pulling an in jffs2_garbage_collect_thread()
|
| /Linux-v5.15/drivers/staging/rtl8712/ |
| D | rtl871x_recv.h | 188 * after pulling, rx_end must be still larger than rx_data. in recvframe_pull_tail()
|
| /Linux-v5.15/net/ipv4/ |
| D | gre_demux.c | 60 * Note that caller must use pskb_may_pull() before pulling GRE header.
|
| /Linux-v5.15/Documentation/dev-tools/kunit/ |
| D | tips.rst | 136 doesn't require pulling in ``<kunit/test.h>``.
|
| /Linux-v5.15/Documentation/i2c/ |
| D | gpio-fault-injection.rst | 100 test and then pulling SDA low for some time. So, the I2C address sent out
|
| /Linux-v5.15/drivers/fpga/ |
| D | dfl-afu-error.c | 72 * - Enable Port by pulling the port out of reset in afu_port_err_clear()
|
| /Linux-v5.15/Documentation/w1/ |
| D | w1-generic.rst | 8 Devices communicate on the bus by pulling the signal to ground via an open
|
| /Linux-v5.15/arch/s390/crypto/ |
| D | arch_random.c | 15 * The worker fills the rng buffer by pulling fresh entropy from the
|
| /Linux-v5.15/net/bluetooth/ |
| D | af_bluetooth.c | 403 /* Pulling partial data */ in bt_sock_stream_recvmsg()
409 /* Pulling all frag data */ in bt_sock_stream_recvmsg()
|
| /Linux-v5.15/Documentation/maintainer/ |
| D | pull-requests.rst | 60 to understand what I'm pulling, and why I should pull it. I also
|
| /Linux-v5.15/drivers/staging/r8188eu/include/ |
| D | rtw_recv.h | 378 /* after pulling, rx_end must be still larger than rx_data. */ in recvframe_pull_tail()
|
| /Linux-v5.15/drivers/usb/phy/ |
| D | phy-gpio-vbus-usb.c | 285 * in use, initialize it to "not pulling up" in gpio_vbus_probe()
|
1234
