| /Linux-v5.10/Documentation/gpu/dp-mst/ |
| D | topology-figure-1.dot | 13 driver -> port3:e;
17 payload2:s -> port3:e;
27 port2 -> mstb3 -> {port3, port4};
28 port3 -> mstb4;
34 port2 -> mstb3 -> {port3, port4};
35 port3 -> mstb4;
50 port3 [label="Port #3";shape=oval];
|
| D | topology-figure-2.dot | 13 driver -> port3:e;
17 payload2:s -> port3:e;
28 port2 -> mstb3 -> {port3, port4};
29 port3 -> mstb4;
36 port2 -> mstb3 -> port3;
39 port3 -> mstb4;
49 port3 [label="Port #3"];
|
| D | topology-figure-3.dot | 16 driver -> port3:e;
19 payload2:s -> port3:e [penwidth=3];
30 port2 -> mstb3 -> {port3, port4};
31 port3 -> mstb4;
39 mstb3 -> port3 [penwidth=3];
42 port3 -> mstb4;
52 port3 [label="Port #3";penwidth=3];
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | r7s9210-rza2mevb.dts | 131 <RZA2_PINMUX(PORT3, 2, 7)>, /* RMII1_CRSDV */
133 <RZA2_PINMUX(PORT3, 5, 7)>, /* RMII1_RXD1 */
134 <RZA2_PINMUX(PORT3, 1, 7)>, /* RMII1_RXER */
135 <RZA2_PINMUX(PORT3, 3, 1)>, /* ET1_MDC */
136 <RZA2_PINMUX(PORT3, 4, 1)>, /* ET1_MDIO */
|
| D | bcm958622hr.dts | 198 label = "port3";
|
| D | bcm958623hr.dts | 202 label = "port3";
|
| D | bcm958625hr.dts | 217 label = "port3";
|
| D | bcm988312hr.dts | 206 label = "port3";
|
| D | bcm958625k.dts | 238 label = "port3";
|
| /Linux-v5.10/Documentation/admin-guide/media/ |
| D | rkisp1.dot | 3 …n00000001 [label="{{<port0> 0 | <port1> 1} | rkisp1_isp\n/dev/v4l-subdev0 | {<port2> 2 | <port3> 3…
6 n00000001:port3 -> n00000014 [style=bold]
|
| D | imx6q-sabresd.dot | 45 …port0> 0} | imx6-mipi-csi2\n/dev/v4l-subdev12 | {<port1> 1 | <port2> 2 | <port3> 3 | <port4> 4}}",…
47 n00000079:port3 -> n0000003d:port0 [style=dashed]
|
| /Linux-v5.10/arch/mips/boot/dts/mscc/ |
| D | ocelot_pcb123.dts | 61 &port3 {
|
| D | ocelot.dtsi | 141 "port2", "port3", "port4", "port5", "port6",
160 port3: port@3 { label
|
| D | ocelot_pcb120.dts | 83 &port3 {
|
| /Linux-v5.10/include/dt-bindings/pinctrl/ |
| D | r7s9210-pinctrl.h | 15 #define PORT3 3 macro
|
| /Linux-v5.10/Documentation/devicetree/bindings/usb/ |
| D | pxa-usb.txt | 10 - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3"
|
| /Linux-v5.10/drivers/usb/host/ |
| D | ohci-pxa27x.c | 81 #define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
92 #define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
105 #define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
377 if (of_property_read_bool(np, "marvell,enable-port3")) in ohci_pxa_of_init()
|
| /Linux-v5.10/net/dsa/ |
| D | tag_ksz.c | 84 * (eg, 0x00=port1, 0x02=port3, 0x06=port7)
145 * (eg, 0x00=port1, 0x02=port3, 0x06=port7)
|
| /Linux-v5.10/Documentation/devicetree/bindings/net/ |
| D | mscc-ocelot.txt | 64 "port2", "port3", "port4", "port5", "port6",
|
| D | keystone-netcp.txt | 78 - sgmii port3/4 module registers (only for NetCP 1.4)
84 index #1 - sgmii port3/4 module registers
|
| /Linux-v5.10/include/sound/ |
| D | emu8000.h | 58 unsigned long port3; /* Port usually at base+0x800 */ member
|
| D | emu8000_reg.h | 18 #define EMU8000_DATA3(e) ((e)->port3)
19 #define EMU8000_PTR(e) ((e)->port3+2)
|
| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | omap-usb-host.txt | 98 port3-mode = "ehci-phy";
|
| /Linux-v5.10/include/uapi/linux/ |
| D | serial.h | 90 int port3; member
|
| /Linux-v5.10/drivers/pinctrl/ |
| D | pinctrl-xway.c | 27 #define PORT3 3 macro
1344 if (port == PORT3) in xway_pinconf_get()
1353 if (port == PORT3) in xway_pinconf_get()
1362 if (port == PORT3) in xway_pinconf_get()
1402 if (port == PORT3) in xway_pinconf_set()
1417 if (port == PORT3) in xway_pinconf_set()
1429 if (port == PORT3) in xway_pinconf_set()
1503 if (port == PORT3) in xway_mux_apply()
1563 if (PORT(pin) == PORT3) in xway_gpio_dir_out()
|
