Searched full:optimum (Results 1 – 25 of 38) sorted by relevance
12
| /Linux-v6.6/include/linux/ |
| D | rational.h | 8 * e.g. when calculating optimum numerator/denominator pairs for
|
| /Linux-v6.6/include/linux/mfd/ |
| D | ac100.h | 106 #define AC100_ADC_DAP_OPT 0x95 /* AGC Optimum */
126 #define AC100_DAC_DAP_OPT 0xb1 /* DRC optimum */
|
| /Linux-v6.6/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-isl29501 | 7 which sets the analog signal levels at an optimum
|
| D | configfs-usb-gadget-uvc | 255 bDefaultFrameIndex optimum frame index for this stream
309 bDefaultFrameIndex optimum frame index for this stream
|
| /Linux-v6.6/Documentation/scsi/ |
| D | BusLogic.rst | 307 may be used to load "Optimum Performance" settings which allow UltraSCSI
310 the "Optimum Performance" settings are loaded.
377 used to load "Optimum Performance" settings which allow UltraSCSI speed to be
380 "Optimum Performance" settings are loaded.
|
| /Linux-v6.6/drivers/accel/ivpu/ |
| D | ivpu_hw.h | 51 * Pll ratio for the efficiency frequency. The VPU has optimum
|
| /Linux-v6.6/arch/alpha/lib/ |
| D | ev6-copy_page.S | 29 conditions were such that I could not reach this optimum rate on
|
| /Linux-v6.6/drivers/scsi/aic7xxx/ |
| D | queue.h | 42 * macro for this purpose for optimum efficiency. A singly-linked list may
53 * should use the explicit macro for this purpose for optimum efficiency.
|
| /Linux-v6.6/drivers/net/wireless/ti/wlcore/ |
| D | conf.h | 981 * Minimum required free tx memory blocks in order to assure optimum
989 * Minimum required free rx memory blocks in order to assure optimum
|
| /Linux-v6.6/drivers/clk/zynqmp/ |
| D | divider.c | 201 * set to optimum based on required total divider value. in zynqmp_clk_divider_round_rate()
|
| /Linux-v6.6/drivers/usb/phy/ |
| D | phy-ab8500-usb.c | 193 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", in ab8500_usb_regulator_enable()
233 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", in ab8500_usb_regulator_disable()
|
| /Linux-v6.6/Documentation/devicetree/bindings/pci/ |
| D | nvidia,tegra194-pcie.yaml | 155 optimum number of FC (Flow Control) credits with downstream devices:
|
| /Linux-v6.6/drivers/net/ethernet/micrel/ |
| D | ks8851_par.c | 88 * bus. To maintain optimum performance, the bus endianness should be set
|
| /Linux-v6.6/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/ |
| D | overview.rst | 382 There is typically one DPIO object per physical CPU for optimum
|
| /Linux-v6.6/drivers/mtd/chips/ |
| D | cfi_cmdset_0020.c | 99 printk(" Vcc Logic Supply Optimum Program/Erase Voltage: %d.%d V\n", in cfi_tell_features()
102 printk(" Vpp Programming Supply Optimum Program/Erase Voltage: %d.%d V\n", in cfi_tell_features()
|
| /Linux-v6.6/lib/ |
| D | inflate.c | 303 than five bits, flat. The optimum values for speed end up being
305 The optimum values may differ though from machine to machine, and
|
| /Linux-v6.6/Documentation/powerpc/ |
| D | hvcs.rst | 10 .. NOTE:Eight space tabs are the optimum editor setting for reading this file.
|
| /Linux-v6.6/drivers/regulator/ |
| D | core.c | 1005 /* Calculate the new optimum regulator operating mode based on the new total
1040 /* set the optimum mode for our new total regulator load */ in drms_uA_update()
1082 /* now get the optimum mode for our new total regulator load */ in drms_uA_update()
1089 rdev_err(rdev, "failed to get optimum mode @ %d uA %d -> %d uV: %pe\n", in drms_uA_update()
1096 rdev_err(rdev, "failed to set optimum mode %x: %pe\n", in drms_uA_update()
|
| /Linux-v6.6/Documentation/admin-guide/pm/ |
| D | cpufreq.rst | 644 The frequency boost mechanism is generally intended to help to achieve optimum
|
| /Linux-v6.6/drivers/crypto/hisilicon/sec/ |
| D | sec_drv.c | 369 * sec_cache_config - configure optimum cache placement
|
| /Linux-v6.6/drivers/scsi/ |
| D | ppa.c | 129 * Also gives a method to use a script to obtain optimum timings (TODO)
|
| D | imm.c | 125 * Also gives a method to use a script to obtain optimum timings (TODO)
|
| /Linux-v6.6/fs/smb/client/ |
| D | cifspdu.h | 979 boundary and optimum performance here */
999 boundary and optimum performance here */
|
| /Linux-v6.6/drivers/scsi/aic94xx/ |
| D | aic94xx_sds.c | 1238 * a optimum balance of 50mus for ERASE which works well in asd_chk_write_status()
|
| /Linux-v6.6/drivers/dma/ |
| D | tegra186-gpc-dma.c | 812 * len to calculate the optimum burst size in get_burst_size()
|
12
