Home
last modified time | relevance | path

Searched +full:nand +full:- +full:ecc +full:- +full:step +full:- +full:size (Results 1 – 25 of 130) sorted by relevance

123456

/Linux-v6.6/Documentation/devicetree/bindings/mtd/
Dhisi504-nand.txt1 Hisilicon Hip04 Soc NAND controller DT binding
5 - compatible: Should be "hisilicon,504-nfc".
6 - reg: The first contains base physical address and size of
7 NAND controller's registers. The second contains base
8 physical address and size of NAND controller's buffer.
9 - interrupts: Interrupt number for nfc.
10 - nand-bus-width: See nand-controller.yaml.
11 - nand-ecc-mode: Support none and hw ecc mode.
12 - #address-cells: Partition address, should be set 1.
13 - #size-cells: Partition size, should be set 1.
[all …]
Dmediatek,mtk-nfc.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/mediatek,mtk-nfc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: MediaTek(MTK) SoCs raw NAND FLASH controller (NFC)
10 - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
15 - mediatek,mt2701-nfc
16 - mediatek,mt2712-nfc
17 - mediatek,mt7622-nfc
21 - description: Base physical address and size of NFI.
[all …]
Dvf610-nfc.txt1 Freescale's NAND flash controller (NFC)
3 This variant of the Freescale NAND flash controller (NFC) can be found on
7 - compatible: Should be set to "fsl,vf610-nfc".
8 - reg: address range of the NFC.
9 - interrupts: interrupt of the NFC.
10 - #address-cells: shall be set to 1. Encode the nand CS.
11 - #size-cells : shall be set to 0.
12 - assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>;
13 - assigned-clock-rates: The NAND bus timing is derived from this clock
14 rate and should not exceed maximum timing for any NAND memory chip
[all …]
Ddenali,nand.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/mtd/denali,nand.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Denali NAND controller
10 - Masahiro Yamada <yamada.masahiro@socionext.com>
15 - altr,socfpga-denali-nand
16 - socionext,uniphier-denali-nand-v5a
17 - socionext,uniphier-denali-nand-v5b
19 reg-names:
[all …]
Dnand-chip.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/nand-chip.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: NAND Chip Common Properties
10 - Miquel Raynal <miquel.raynal@bootlin.com>
13 - $ref: mtd.yaml#
16 This file covers the generic description of a NAND chip. It implies that the
17 bus interface should not be taken into account: both raw NAND devices and
18 SPI-NAND devices are concerned by this description.
[all …]
Damlogic,meson-nand.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/amlogic,meson-nand.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs
10 - $ref: nand-controller.yaml
13 - liang.yang@amlogic.com
18 - amlogic,meson-gxl-nfc
19 - amlogic,meson-axg-nfc
24 reg-names:
[all …]
Dmarvell,nand-controller.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Marvell NAND Flash Controller (NFC)
10 - Miquel Raynal <miquel.raynal@bootlin.com>
15 - items:
16 - const: marvell,armada-8k-nand-controller
17 - const: marvell,armada370-nand-controller
18 - enum:
[all …]
Dbrcm,brcmnand.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Broadcom STB NAND Controller
10 - Brian Norris <computersforpeace@gmail.com>
11 - Kamal Dasu <kdasu.kdev@gmail.com>
14 The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND
15 flash chips. It has a memory-mapped register interface for both control
25 -- Additional SoC-specific NAND controller properties --
27 The NAND controller is integrated differently on the variety of SoCs on which
[all …]
Drockchip,nand-controller.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/rockchip,nand-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Rockchip SoCs NAND FLASH Controller (NFC)
10 - $ref: nand-controller.yaml#
13 - Heiko Stuebner <heiko@sntech.de>
18 - const: rockchip,px30-nfc
19 - const: rockchip,rk2928-nfc
20 - const: rockchip,rv1108-nfc
[all …]
Dnvidia-tegra20-nand.txt1 NVIDIA Tegra NAND Flash controller
4 - compatible: Must be one of:
5 - "nvidia,tegra20-nand"
6 - reg: MMIO address range
7 - interrupts: interrupt output of the NFC controller
8 - clocks: Must contain an entry for each entry in clock-names.
9 See ../clocks/clock-bindings.txt for details.
10 - clock-names: Must include the following entries:
11 - nand
12 - resets: Must contain an entry for each entry in reset-names.
[all …]
Draw-nand-chip.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/raw-nand-chip.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Raw NAND Chip Common Properties
10 - Miquel Raynal <miquel.raynal@bootlin.com>
13 - $ref: nand-chip.yaml#
16 The ECC strength and ECC step size properties define the user
18 they request the ECC engine to correct {strength} bit errors per
19 {size} bytes for a particular raw NAND chip.
[all …]
Dingenic,nand.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/ingenic,nand.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Ingenic SoCs NAND controller
10 - Paul Cercueil <paul@crapouillou.net>
13 - $ref: nand-controller.yaml#
14 - $ref: /schemas/memory-controllers/ingenic,nemc-peripherals.yaml#
19 - ingenic,jz4740-nand
20 - ingenic,jz4725b-nand
[all …]
Dfsmc-nand.txt2 NAND Interface
5 - compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand"
6 - reg : Address range of the mtd chip
7 - reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd"
10 - bank-width : Width (in bytes) of the device. If not present, the width
12 - nand-skip-bbtscan: Indicates the BBT scanning should be skipped
13 - timings: array of 6 bytes for NAND timings. The meanings of these bytes
20 kept in Hi-Z (tristate) after the start of a write access.
27 NAND flash in response to SMWAITn. Zero means 1 cycle,
32 - bank: default NAND bank to use (0-3 are valid, 0 is the default).
[all …]
Dst,stm32-fmc2-nand.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/st,stm32-fmc2-nand.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Christophe Kerello <christophe.kerello@foss.st.com>
15 - st,stm32mp15-fmc2
16 - st,stm32mp1-fmc2-nfc
27 - description: tx DMA channel
28 - description: rx DMA channel
29 - description: ecc DMA channel
[all …]
/Linux-v6.6/drivers/mtd/nand/
Decc-mxic.c1 // SPDX-License-Identifier: GPL-2.0
3 * Support for Macronix external hardware ECC engine for NAND devices, also
10 #include <linux/dma-mapping.h>
18 #include <linux/mtd/nand.h>
19 #include <linux/mtd/nand-ecc-mxic.h>
53 /* ECC Chunk Size */
55 /* Main Data Size */
57 /* Spare Data Size */
63 /* ECC Chunk Count */
98 /* ECC machinery */
[all …]
Decc-sw-bch.c1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * This file provides ECC correction for more than 1 bit per block of data,
14 #include <linux/mtd/nand.h>
15 #include <linux/mtd/nand-ecc-sw-bch.h>
18 * nand_ecc_sw_bch_calculate - Calculate the ECC corresponding to a data block
19 * @nand: NAND device
21 * @code: Output buffer with ECC
23 int nand_ecc_sw_bch_calculate(struct nand_device *nand, in nand_ecc_sw_bch_calculate() argument
26 struct nand_ecc_sw_bch_conf *engine_conf = nand->ecc.ctx.priv; in nand_ecc_sw_bch_calculate()
29 memset(code, 0, engine_conf->code_size); in nand_ecc_sw_bch_calculate()
[all …]
/Linux-v6.6/include/linux/mtd/
Drawnand.h1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org>
8 * Contains standard defines and IDs for NAND flash devices
17 #include <linux/mtd/nand.h>
29 /* The maximum number of NAND chips in an array */
50 * Standard NAND flash commands
75 #define NAND_CMD_NONE -1
84 #define NAND_DATA_IFACE_CHECK_ONLY -1
87 * Constants for Hardware ECC
89 /* Reset Hardware ECC for read */
[all …]
/Linux-v6.6/drivers/mtd/nand/raw/
Dsunxi_nand.c1 // SPDX-License-Identifier: GPL-2.0+
6 * https://github.com/yuq/sunxi-nfc-mtd
9 * https://github.com/hno/Allwinner-Info
16 #include <linux/dma-mapping.h>
70 #define NFC_PAGE_SHIFT(x) (((x) < 10 ? 0 : (x) - 10) << 8)
107 #define NFC_ADR_NUM(x) (((x) - 1) << 16)
161 * struct sunxi_nand_chip_sel - stores information related to NAND Chip Select
163 * @cs: the NAND CS id used to communicate with a NAND Chip
164 * @rb: the Ready/Busy pin ID. -1 means no R/B pin connected to the NFC
172 * struct sunxi_nand_hw_ecc - stores information related to HW ECC support
[all …]
Domap2.c1 // SPDX-License-Identifier: GPL-2.0-only
10 #include <linux/dma-mapping.h>
18 #include <linux/mtd/nand-ecc-sw-bch.h>
21 #include <linux/omap-dma.h>
29 #include <linux/omap-gpmc.h>
30 #include <linux/platform_data/mtd-nand-omap2.h>
32 #define DRIVER_NAME "omap2-nand"
122 /* GPMC ecc engine settings for read */
129 /* GPMC ecc engine settings for write */
145 struct nand_chip nand; member
[all …]
/Linux-v6.6/Documentation/ABI/testing/
Dsysfs-class-mtd4 Contact: linux-mtd@lists.infradead.org
12 Contact: linux-mtd@lists.infradead.org
22 Contact: linux-mtd@lists.infradead.org
24 These directories provide the corresponding read-only device
30 Contact: linux-mtd@lists.infradead.org
34 read-write device so <minor> will be even.
39 Contact: linux-mtd@lists.infradead.org
42 to the read-only variant of the MTD device (in
48 Contact: linux-mtd@lists.infradead.org
50 "Major" erase size for the device. If numeraseregions is
[all …]
/Linux-v6.6/arch/arm/boot/dts/broadcom/
Dbcm5301x-nand-cs0-bch8.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
3 * Broadcom BCM470X / BCM5301X Nand chip defaults.
5 * This should be included if the NAND controller is on chip select 0
6 * and uses 8 bit ECC.
8 * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de>
11 #include "bcm5301x-nand-cs0.dtsi"
14 nand-ecc-algo = "bch";
15 nand-ecc-strength = <8>;
16 nand-ecc-step-size = <512>;
Dbcm5301x-nand-cs0-bch1.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
3 * Broadcom Northstar NAND.
8 #include "bcm5301x-nand-cs0.dtsi"
11 nand-ecc-algo = "bch";
12 nand-ecc-strength = <1>;
13 nand-ecc-step-size = <512>;
Dbcm5301x-nand-cs0-bch4.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
6 #include "bcm5301x-nand-cs0.dtsi"
9 nand-ecc-algo = "bch";
10 nand-ecc-strength = <4>;
11 nand-ecc-step-size = <512>;
/Linux-v6.6/drivers/mtd/nand/raw/gpmi-nand/
Dgpmi-nand.c1 // SPDX-License-Identifier: GPL-2.0+
3 * Freescale GPMI NAND Flash Driver
5 * Copyright (C) 2010-2015 Freescale Semiconductor, Inc.
18 #include <linux/dma/mxs-dma.h>
19 #include "gpmi-nand.h"
20 #include "gpmi-regs.h"
21 #include "bch-regs.h"
23 /* Resource names for the GPMI NAND driver. */
24 #define GPMI_NAND_GPMI_REGS_ADDR_RES_NAME "gpmi-nand"
52 while ((readl(addr) & mask) && --timeout) in clear_poll_bit()
[all …]
/Linux-v6.6/arch/mips/boot/dts/brcm/
Dbcm97xxx-nand-cs1-bch4.dtsi1 // SPDX-License-Identifier: GPL-2.0
2 &nand {
6 nand-on-flash-bbt;
8 nand-ecc-strength = <4>;
9 nand-ecc-step-size = <512>;
10 brcm,nand-oob-sector-size = <16>;
13 compatible = "fixed-partitions";
14 #address-cells = <1>;
15 #size-cells = <1>;

123456