Searched full:multiplex (Results 1 – 25 of 77) sorted by relevance
1234
| /Linux-v5.15/include/linux/platform_data/ |
| D | gpmc-omap.h | 136 #define GPMC_MUX_AAD 1 /* Addr-Addr-Data multiplex */
137 #define GPMC_MUX_AD 2 /* Addr-Data multiplex */
150 u32 mux_add_data; /* multiplex address & data */
|
| /Linux-v5.15/drivers/staging/media/atomisp/pci/hive_isp_css_include/host/ |
| D | fifo_monitor_public.h | 25 /*! Set a fifo switch multiplex
38 /*! Get a fifo switch multiplex
|
| /Linux-v5.15/arch/mips/txx9/ |
| D | Kconfig | 109 comment "Multiplex Pin Select"
|
| /Linux-v5.15/include/linux/can/platform/ |
| D | cc770.h | 7 #define CPUIF_MUX 0x04 /* Multiplex */
|
| /Linux-v5.15/arch/arm/mach-davinci/ |
| D | mux.h | 2 * Pin-multiplex helper macros for TI DaVinci family devices
|
| /Linux-v5.15/Documentation/devicetree/bindings/interrupt-controller/ |
| D | fsl,intmux.yaml | 23 Should contain the parent interrupt lines (up to 8) used to multiplex
|
| D | fsl,irqsteer.yaml | 25 should contain the up to 8 parent interrupt lines used to multiplex
|
| /Linux-v5.15/include/linux/fsl/ |
| D | guts.h | 53 * Multiplex Control
56 * multiplex control 2
134 /* Alternate function signal multiplex control */
|
| /Linux-v5.15/Documentation/devicetree/bindings/phy/ |
| D | qcom,usb-8x16-phy.txt | 54 controlled by GPIO to de/multiplex D+/D- USB lines
|
| /Linux-v5.15/drivers/gpu/drm/msm/disp/dpu1/ |
| D | dpu_hw_sspp.h | 157 * @mode: parallel or time multiplex multirect mode
287 * @mode: parallel fetch / time multiplex multirect mode
|
| D | dpu_plane.h | 24 * @multirect_mode: parallel or time multiplex multirect mode
|
| /Linux-v5.15/Documentation/userspace-api/media/v4l/ |
| D | vidioc-enumstd.rst | 339 multiplex. (NICAM system)
344 DQPSK modulated with a 728 kbit/s sound and data multiplex able to
|
| /Linux-v5.15/Documentation/devicetree/bindings/pinctrl/ |
| D | renesas,rzn1-pinctrl.yaml | 68 These identifiers collapse the IO Multiplex Configuration Level 1
|
| D | st,stm32-pinctrl.yaml | 16 also provides ability to multiplex and configure the output of various
|
| /Linux-v5.15/Documentation/devicetree/bindings/usb/ |
| D | msm-hsusb.txt | 56 SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex
|
| /Linux-v5.15/drivers/media/pci/cx18/ |
| D | cx18-cards.h | 115 u32 hw_muxer; /* hardware used to multiplex audio input */
|
| /Linux-v5.15/Documentation/devicetree/bindings/dma/ |
| D | fsl-edma.txt | 3 The eDMA channels have multiplex capability by programmble memory-mapped
|
| /Linux-v5.15/drivers/video/fbdev/ |
| D | s3fb.c | 605 u32 value, mode, hmul, offset_value, screen_size, multiplex, dbytes; in s3fb_set_par() local
754 multiplex = 0; in s3fb_set_par()
809 multiplex = 1; in s3fb_set_par()
826 multiplex = 1; in s3fb_set_par()
854 multiplex = 1; in s3fb_set_par()
884 svga_wseq_mask(par->state.vgabase, 0x15, multiplex ? 0x10 : 0x00, 0x10); in s3fb_set_par()
885 svga_wseq_mask(par->state.vgabase, 0x18, multiplex ? 0x80 : 0x00, 0x80); in s3fb_set_par()
|
| /Linux-v5.15/drivers/staging/fbtft/ |
| D | fb_sh1106.c | 43 /* Set Multiplex Ratio */ in init_display()
|
| D | fb_ssd1305.c | 53 /* Set Multiplex Ratio */ in init_display()
|
| D | fb_ssd1306.c | 52 /* Set Multiplex Ratio */ in init_display()
|
| /Linux-v5.15/arch/sh/include/mach-common/mach/ |
| D | sh2007.h | 52 /* Multiplex (0-1:0,1) */
|
| /Linux-v5.15/Documentation/devicetree/bindings/bus/ |
| D | intel,ixp4xx-expansion-bus-controller.yaml | 103 description: Multiplex address and data on the data bus.
|
| /Linux-v5.15/Documentation/driver-api/ |
| D | pin-control.rst | 23 can control PINs. It may be able to multiplex, bias, set load capacitance,
818 multiplex
822 whether the pin is used for GPIO or not. If you multiplex a GPIO onto a
850 multiplex
857 possible that the GPIO, pin config and pin multiplex registers are placed into
|
| /Linux-v5.15/arch/powerpc/platforms/ |
| D | Kconfig | 84 cpu. This will enable the generic code to multiplex the 4
|
1234
