Searched full:millivolt (Results 1 – 25 of 29) sorted by relevance
12
| /Linux-v5.15/Documentation/devicetree/bindings/sound/ |
| D | da7218.txt | 28 - dlg,micbias1-lvl-millivolt : Voltage (mV) for Mic Bias 1
30 - dlg,micbias2-lvl-millivolt : Voltage (mV) for Mic Bias 2
84 dlg,micbias1-lvl-millivolt = <2600>;
85 dlg,micbias2-lvl-millivolt = <2600>;
|
| D | cs35l36.txt | 13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
73 - cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold.
148 cirrus,boost-ctl-millivolt = <10000>;
|
| D | cs35l35.txt | 55 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
150 cirrus,boost-ctl-millivolt = <9000>;
162 cirrus,classh-headroom-millivolt = <0x0B>;
|
| D | cs35l34.txt | 13 - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
|
| /Linux-v5.15/Documentation/hwmon/ |
| D | sysfs-interface.rst | 124 Unit: millivolt
131 Unit: millivolt
142 Unit: millivolt
149 Unit: millivolt
160 Unit: millivolt
181 Unit: millivolt
188 Unit: millivolt
195 Unit: millivolt
234 Unit: millivolt
255 Unit: millivolt
[all …]
|
| D | ltc2990.rst | 44 in0_input Voltage at Vcc pin in millivolt (range 2.5V to 5V)
52 in[1-4]_input Voltage at V[1-4] pin in millivolt
|
| D | ibmpowernv.rst | 51 inX_input Measured power supply voltage (millivolt)
|
| /Linux-v5.15/Documentation/devicetree/bindings/rtc/ |
| D | microcrystal,rv3032.yaml | 34 trickle-voltage-millivolt:
59 trickle-voltage-millivolt = <1750>;
|
| D | rtc.yaml | 53 trickle-voltage-millivolt:
|
| /Linux-v5.15/Documentation/devicetree/bindings/phy/ |
| D | brcm,sata-phy.yaml | 86 "brcm,tx-amplitude-millivolt":
88 Transmit amplitude voltage in millivolt.
|
| /Linux-v5.15/drivers/hwmon/ |
| D | mcp3021.c | 25 /* Vdd / reference voltage in millivolt */
49 u32 vdd; /* supply and reference voltage in millivolt */
|
| D | atxp1.c | 146 * unit: millivolt
|
| D | da9052-hwmon.c | 434 /* convert from microvolt (DT) to millivolt (hwmon) */ in da9052_hwmon_probe()
|
| D | corsair-cpro.c | 43 * rcv: returns millivolt in bytes 1,2
|
| /Linux-v5.15/Documentation/devicetree/bindings/power/supply/ |
| D | active-semi,act8945a-charger.yaml | 33 Despite the name, specified values are in millivolt (mV).
|
| /Linux-v5.15/arch/arm64/boot/dts/qcom/ |
| D | pm660l.dtsi | 76 qcom,ovp-millivolt = <29600>;
|
| D | sdm845.dtsi | 3611 qcom,micbias1-millivolt = <1800>;
3612 qcom,micbias2-millivolt = <1800>;
3613 qcom,micbias3-millivolt = <1800>;
3614 qcom,micbias4-millivolt = <1800>;
|
| /Linux-v5.15/Documentation/devicetree/bindings/leds/backlight/ |
| D | qcom-wled.yaml | 94 qcom,ovp-millivolt:
|
| /Linux-v5.15/include/linux/iio/ |
| D | consumer.h | 390 * unit for the channel type. E.g. millivolt for voltage channels, if you want
|
| /Linux-v5.15/drivers/video/backlight/ |
| D | qcom-wled.c | 1366 .name = "qcom,ovp-millivolt", in wled_configure()
1394 .name = "qcom,ovp-millivolt", in wled_configure()
|
| /Linux-v5.15/drivers/rtc/ |
| D | rtc-rv3032.c | 522 if (!device_property_read_u32(dev, "trickle-voltage-millivolt", &voltage)) { in rv3032_trickle_charger_setup()
|
| /Linux-v5.15/drivers/phy/broadcom/ |
| D | phy-brcm-sata.c | 819 of_property_read_u32(child, "brcm,tx-amplitude-millivolt", in brcm_sata_phy_probe()
|
| /Linux-v5.15/sound/soc/codecs/ |
| D | cs35l36.c | 1443 ret = of_property_read_u32(np, "cirrus,boost-ctl-millivolt", &val); in cs35l36_handle_of_data()
1453 "Unable to find required parameter 'cirrus,boost-ctl-millivolt'"); in cs35l36_handle_of_data()
|
| D | cs35l34.c | 815 if (of_property_read_u32(np, "cirrus,boost-vtge-millivolt", in cs35l34_handle_of_data()
|
| /Linux-v5.15/drivers/power/supply/ |
| D | sc27xx_fuel_gauge.c | 86 * @max_volt: the maximum constant input voltage in millivolt
|
12
