Searched full:manually (Results 1 – 25 of 1080) sorted by relevance
12345678910>>...44
| /Linux-v6.6/arch/sh/include/asm/ |
| D | watchdog.h | 76 * The upper byte is set manually on each write.
88 * The upper byte is set manually on each write.
109 * register. The upper byte is set manually on each write.
130 * The upper byte is set manually on each write.
152 * register. The upper byte is set manually on each write.
|
| /Linux-v6.6/tools/memory-model/scripts/ |
| D | README | 43 name per line on standard input. Not normally run manually,
56 the test ran correctly. Not normally run manually, provided
67 Parse command-line arguments. Not normally run manually,
73 name per line on standard input. Not normally run manually,
|
| /Linux-v6.6/drivers/of/ |
| D | Kconfig | 10 be enabled manually for unittests, overlays or
75 can enable it manually to improve device tree unit test coverage.
100 enable it manually to improve device tree unit test coverage.
|
| /Linux-v6.6/Documentation/w1/ |
| D | w1-generic.rst | 93 w1_master_add (rw) manually register a slave device
98 w1_master_remove (rw) manually remove a slave device
110 set to zero, then manually add the slave device serial numbers by
113 redetect manually removed devices that are present and timeout manually
|
| /Linux-v6.6/Documentation/networking/dsa/ |
| D | configuration.rst | 8 network configuration suites by now and has to be performed manually.
100 # brought up manually before the slave ports.
112 # brought up manually before the slave ports.
138 # brought up manually before the slave ports.
182 # brought up manually before the slave ports.
225 # brought up manually before the slave ports.
265 # brought up manually before the slave ports.
|
| /Linux-v6.6/Documentation/admin-guide/ |
| D | module-signing.rst | 10 .. - Manually signing modules.
73 be signed manually using::
164 It is also possible to manually generate the key private/public files using the
212 Manually signing modules
215 To manually sign a module, use the scripts/sign-file tool available in
|
| /Linux-v6.6/drivers/gpu/drm/radeon/ |
| D | radeon_sync.c | 143 /* not enough room, wait manually */ in radeon_sync_rings()
162 /* signaling wasn't successful wait manually */ in radeon_sync_rings()
172 /* waiting wasn't successful wait manually */ in radeon_sync_rings()
|
| /Linux-v6.6/drivers/hid/i2c-hid/ |
| D | Kconfig | 27 # No "depends on OF" because this can also be used for manually
35 well as binding to manually (board-file) instantiated i2c-hid-clients.
|
| /Linux-v6.6/include/linux/ |
| D | devm-helpers.h | 18 * is typical example where IRQs are often devm-managed and WQs are manually
19 * cleaned at remove(). If IRQs are not manually freed at remove() (and this is
|
| D | reset-controller.h | 14 * @assert: manually assert the reset line, if supported
15 * @deassert: manually deassert the reset line, if supported
|
| D | mmap_lock.h | 80 * This should normally NOT be called manually from other places.
81 * If you want to call this manually anyway, keep in mind that this will release
|
| /Linux-v6.6/arch/arc/include/asm/ |
| D | entry-arcv2.h | 59 ; 4b. If Auto-save (optional) not enabled in hw, manually save them
60 ; 5. Manually save: r12,r30, sp,fp,gp, ACCL pair
84 ; Now manually save rest of reg file
118 * This macro saves the registers manually which would normally be autosaved
|
| /Linux-v6.6/drivers/cpufreq/ |
| D | Kconfig | 68 you to set the CPU frequency manually or when a userspace
70 to enable the userspace governor manually.
136 CPU frequency manually or when a userspace program shall
|
| /Linux-v6.6/arch/nios2/platform/ |
| D | Kconfig.platform | 14 Please not that this address is used directly so you have to manually
26 Please note that this address is used directly so you have to manually
|
| /Linux-v6.6/drivers/net/wireless/ath/ath5k/ |
| D | ani.h | 44 * @ATH5K_ANI_MODE_MANUAL_LOW: Manually set all immunity parameters to low,
46 * @ATH5K_ANI_MODE_MANUAL_HIGH: Manually set all immunity parameters to high,
|
| /Linux-v6.6/Documentation/driver-api/ |
| D | ipmb.rst | 45 The driver needs to be loaded at boot time or manually first.
81 2) Manually from Linux::
|
| /Linux-v6.6/Documentation/rust/ |
| D | quick-start.rst | 69 In this case, upgrading the Rust compiler version later on requires manually
140 can be installed manually::
156 can be installed manually::
|
| /Linux-v6.6/samples/bpf/ |
| D | README.rst | 64 Manually compiling LLVM with 'bpf' support
79 Quick sniplet for manually compiling LLVM and clang
|
| /Linux-v6.6/Documentation/networking/device_drivers/ethernet/ti/ |
| D | am65_nuss_cpsw_switchdev.rst | 108 Manually adding FDBs::
118 Manually adding MDBs::
|
| /Linux-v6.6/block/ |
| D | Kconfig | 36 created on demand, but scripts that manually create device nodes and
59 normally need to manually enable this.
|
| /Linux-v6.6/fs/afs/ |
| D | dynroot.c | 274 * Create a manually added cell mount directory.
304 * Remove a manually added cell mount directory.
384 /* Remove all the pins for dirs created for manually added cells */ in afs_dynroot_depopulate()
|
| /Linux-v6.6/Documentation/dev-tools/kunit/ |
| D | running_tips.rst | 143 Running tests manually
352 This report can be accessed when running KUnit manually by passing in the
385 You can use this filtering feature when running KUnit manually by passing
391 running KUnit manually, use the module param ``kunit.filter_action=skip``.
|
| /Linux-v6.6/Documentation/hwmon/ |
| D | bt1-pvt.rst | 34 must switch from one sensor to another, read converted data and manually check
103 be used to manually adjust the
|
| /Linux-v6.6/Documentation/driver-api/media/ |
| D | v4l2-device.rst | 20 dev->driver_data manually to point to the driver-specific device structure
128 decrease the refcount manually as well by calling:
|
| /Linux-v6.6/drivers/gpu/drm/tidss/ |
| D | tidss_drv.c | 148 /* If we don't have PM, we need to call resume manually */ in tidss_probe()
215 /* If we don't have PM, we need to call suspend manually */ in tidss_remove()
|
12345678910>>...44
