Searched full:mainly (Results 1 – 25 of 428) sorted by relevance
12345678910>>...18
| /Linux-v5.10/include/linux/soc/samsung/ |
| D | s3c-cpu-freq.h | 19 * struct s3c_freq - frequency information (mainly for core drivers)
27 * mainly for the core drivers to ensure we do not end up passing about
|
| /Linux-v5.10/drivers/mmc/host/ |
| D | sdhci-bcm-kona.c | 85 * is very low w.r.t AHB clock, mainly during boot-time and during card in sdhci_bcm_kona_sd_reset()
110 * is very low w.r.t AHB clock, mainly during boot-time and during card in sdhci_bcm_kona_sd_init()
132 * is very low w.r.t AHB clock, mainly during boot-time and during card in sdhci_bcm_kona_sd_card_emulate()
|
| /Linux-v5.10/drivers/hsi/ |
| D | Kconfig | 9 synchronous serial interface used mainly to connect
|
| /Linux-v5.10/Documentation/devicetree/bindings/sound/ |
| D | widgets.txt | 3 This mainly specifies audio off-codec DAPM widgets.
|
| /Linux-v5.10/Documentation/devicetree/bindings/pwm/ |
| D | ti,twl-pwmled.txt | 5 On TWL6030 series: LED PWM (mainly used as charging indicator LED)
|
| /Linux-v5.10/drivers/vme/bridges/ |
| D | Kconfig | 23 is mainly useful for VME development (in the absence of VME
|
| /Linux-v5.10/drivers/i3c/ |
| D | Kconfig | 14 mainly designed to communicate with sensors.
|
| /Linux-v5.10/Documentation/ABI/testing/ |
| D | sysfs-bus-hsi | 7 serial interface mainly used for connecting application
|
| /Linux-v5.10/drivers/iio/dummy/ |
| D | Kconfig | 16 Driver intended mainly as documentation for how to write
|
| /Linux-v5.10/drivers/gpu/drm/omapdrm/ |
| D | TODO | 6 . This is mainly theoretical since most of these devices don't actually
|
| /Linux-v5.10/Documentation/arm/ |
| D | interrupts.rst | 13 There is more assembly code inside each of these functions, mainly to
48 We also bring the idea of an IRQ "chip" (mainly to reduce the size of
|
| /Linux-v5.10/fs/squashfs/ |
| D | Kconfig | 130 compressed with LZ4 compression. LZ4 compression is mainly
145 compressed with LZO compression. LZO compression is mainly
|
| /Linux-v5.10/Documentation/devicetree/bindings/memory-controllers/ |
| D | ath79-ddr-controller.txt | 4 to flush the FIFO between various devices and the DDR. This is mainly used
|
| /Linux-v5.10/drivers/nvdimm/ |
| D | pfn.h | 36 * configurations mainly to allow a backup, reconfigure the
|
| /Linux-v5.10/tools/testing/selftests/sync/ |
| D | sw_sync.h | 33 * sw_sync is mainly intended for testing and should not be compiled into
|
| /Linux-v5.10/block/partitions/ |
| D | Kconfig | 167 This is mainly used to carry data from a UnixWare box to your
234 above. This is mainly used to carry data from a SPARC under SunOS to
|
| /Linux-v5.10/include/asm-generic/ |
| D | checksum.h | 60 * this routine is used for miscellaneous IP-like checksums, mainly
|
| /Linux-v5.10/Documentation/admin-guide/nfs/ |
| D | nfsd-admin-interfaces.rst | 8 nfsd is controlled mainly by pseudofiles under the "nfsd" filesystem,
|
| /Linux-v5.10/Documentation/filesystems/ext4/ |
| D | bigalloc.rst | 17 file system is mainly going to be storing large files in the 4-32
|
| /Linux-v5.10/Documentation/leds/ |
| D | leds-lp3944.rst | 43 The chip is used mainly in embedded contexts, so this driver expects it is
|
| /Linux-v5.10/drivers/acpi/apei/ |
| D | Kconfig | 60 mainly used for debugging and testing the other parts of
|
| /Linux-v5.10/fs/romfs/ |
| D | Kconfig | 6 This is a very small read-only file system mainly intended for
|
| /Linux-v5.10/include/linux/ |
| D | ti_wilink_st.h | 96 * in progress, this is mainly used to return relevant err codes
230 * mainly used during fw download, which involves multiple send/wait
242 * @core_data: ST core's data, which mainly is the tty's disc_data
|
| /Linux-v5.10/arch/ia64/include/asm/ |
| D | checksum.h | 41 * This routine is used for miscellaneous IP-like checksums, mainly in
|
| /Linux-v5.10/Documentation/devicetree/bindings/arm/ |
| D | coresight-cpu-debug.txt | 5 external debug module is mainly used for two modes: self-hosted debug and
|
12345678910>>...18
