Searched full:magnetometer (Results 1 – 25 of 63) sorted by relevance
123
| /Linux-v5.10/drivers/iio/magnetometer/ |
| D | Kconfig | 3 # Magnetometer sensors
7 menu "Magnetometer sensors"
10 tristate "Asahi Kasei AK8974 3-Axis Magnetometer"
18 AMI306 I2C-based 3-axis magnetometer chips.
24 tristate "Asahi Kasei AK8975 3-Axis Magnetometer"
31 AK09911 or AK09912 3-Axis Magnetometer.
50 tristate "Bosch BMC150 I2C Magnetometer Driver"
55 Say yes here to build support for the BMC150 magnetometer with
58 This is a combo module with both accelerometer and magnetometer.
59 This driver is only implementing magnetometer part, which has
[all …]
|
| D | bmc150_magn_spi.c | 3 * 3-axis magnetometer driver support following SPI Bosch-Sensortec chips:
67 MODULE_DESCRIPTION("BMC150 magnetometer SPI driver");
|
| D | bmc150_magn_i2c.c | 3 * 3-axis magnetometer driver supporting following I2C Bosch-Sensortec chips:
82 MODULE_DESCRIPTION("BMC150 I2C magnetometer driver");
|
| D | Makefile | 3 # Makefile for industrial I/O Magnetometer sensor drivers
|
| D | rm3100-i2c.c | 53 MODULE_DESCRIPTION("PNI RM3100 3-axis magnetometer i2c driver");
|
| /Linux-v5.10/drivers/iio/imu/inv_mpu6050/ |
| D | inv_mpu_magn.c | 15 * MPU9xxx magnetometer are AKM chips on I2C aux bus
59 /* init magnetometer chip */
144 * inv_mpu_magn_probe() - probe and setup magnetometer chip
150 * Noop if there is no magnetometer in the chip.
224 * inv_mpu_magn_set_rate() - set magnetometer sampling rate
231 * magnetometer chip. Resulting in duplicated data for higher frequencies.
232 * Noop if there is no magnetometer in the chip.
255 * inv_mpu_magn_set_orient() - fill magnetometer mounting matrix
260 * Fill magnetometer mounting matrix using the provided chip matrix.
268 /* fill magnetometer orientation */ in inv_mpu_magn_set_orient()
[all …]
|
| D | inv_mpu_magn.h | 13 /* Magnetometer maximum frequency */
19 * inv_mpu_magn_get_scale() - get magnetometer scale value
|
| D | inv_mpu_i2c.c | 58 * MPU9xxx magnetometer support requires to disable i2c auxiliary bus. in inv_mpu_i2c_aux_setup()
61 * Check for i2c-gate node in devicetree and set magnetometer disabled. in inv_mpu_i2c_aux_setup()
71 dev_warn(dev, "disable internal use of magnetometer\n"); in inv_mpu_i2c_aux_setup()
|
| D | inv_mpu_iio.h | 86 /* chip sensors mask: accelerometer, gyroscope, temperature, magnetometer */
171 * @magn_disabled: magnetometer disabled for backward compatibility reason.
173 * @magn_orient: magnetometer sensor chip orientation if available.
308 /* MPU9X50 9-axis magnetometer */
|
| /Linux-v5.10/Documentation/devicetree/bindings/iio/magnetometer/ |
| D | hmc5843.txt | 1 * Honeywell HMC5843 magnetometer sensor
10 - reg : the I2C address of the magnetometer - typically 0x1e
14 - gpios : should be device tree identifier of the magnetometer DRDY pin
|
| D | mag3110.txt | 1 * FREESCALE MAG3110 magnetometer sensor
6 - reg : the I2C address of the magnetometer
20 magnetometer@e {
|
| D | asahi-kasei,ak8975.yaml | 4 $id: http://devicetree.org/schemas/iio/magnetometer/asahi-kasei,ak8975.yaml#
7 title: AsahiKASEI AK8975 magnetometer sensor
68 magnetometer@c {
|
| D | mmc35240.txt | 1 * MEMSIC MMC35240 magnetometer sensor
6 - reg : the I2C address of the magnetometer
|
| D | bmc150_magn.txt | 1 * Bosch BMC150 magnetometer sensor
12 - reg : the I2C address of the magnetometer
|
| D | ak8974.txt | 1 * Asahi Kasei AK8974 magnetometer sensor
8 - reg : the I2C address of the magnetometer
|
| D | pni,rm3100.txt | 1 * PNI RM3100 3-axis magnetometer sensor
|
| /Linux-v5.10/drivers/iio/imu/bmi160/ |
| D | Kconfig | 18 accelerometer, gyroscope and external BMG160 magnetometer.
30 accelerometer, gyroscope and external BMG160 magnetometer.
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | ste-href-stuib.dtsi | 92 /* Magnetometer */
165 magnetometer {
167 /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
|
| D | ste-href-tvk1281618.dtsi | 87 /* Magnetometer */
192 * and AK8974 magnetometer.
|
| /Linux-v5.10/Documentation/devicetree/bindings/iio/imu/ |
| D | nxp,fxos8700.yaml | 13 Accelerometer and magnetometer combo device with an i2c and SPI interface.
14 …tion-sensors/6-axis/digital-motion-sensor-3d-accelerometer-2g-4g-8g-plus-3d-magnetometer:FXOS8700CQ
|
| /Linux-v5.10/drivers/iio/imu/ |
| D | Kconfig | 84 tristate "Kionix KMX61 6-axis accelerometer and magnetometer"
90 accelerometer and magnetometer.
|
| D | adis16400.c | 44 #define ADIS16400_XMAGN_OUT 0x10 /* X-axis magnetometer measurement */
45 #define ADIS16400_YMAGN_OUT 0x12 /* Y-axis magnetometer measurement */
46 #define ADIS16400_ZMAGN_OUT 0x14 /* Z-axis magnetometer measurement */
68 #define ADIS16400_XMAGN_HIF 0x26 /* X-axis magnetometer, hard-iron factor */
69 #define ADIS16400_YMAGN_HIF 0x28 /* Y-axis magnetometer, hard-iron factor */
70 #define ADIS16400_ZMAGN_HIF 0x2A /* Z-axis magnetometer, hard-iron factor */
71 #define ADIS16400_XMAGN_SIF 0x2C /* X-axis magnetometer, soft-iron factor */
72 #define ADIS16400_YMAGN_SIF 0x2E /* Y-axis magnetometer, soft-iron factor */
73 #define ADIS16400_ZMAGN_SIF 0x30 /* Z-axis magnetometer, soft-iron factor */
|
| D | fxos8700_core.c | 3 * FXOS8700 - NXP IMU (accelerometer plus magnetometer)
293 * Accellerometer and magnetometer have the same ODR options, set in the
353 dev_err(dev, "Magnetometer scale is locked at 1200uT\n"); in fxos8700_set_scale()
375 *uscale = 1200; /* Magnetometer is locked at 1200uT */ in fxos8700_get_scale()
|
| /Linux-v5.10/drivers/iio/common/cros_ec_sensors/ |
| D | Kconfig | 21 Accelerometers, Gyroscope and Magnetometer that are
|
| /Linux-v5.10/drivers/iio/ |
| D | Makefile | 31 obj-y += magnetometer/
|
123
