| /Linux-v6.1/drivers/platform/x86/ |
| D | gpd-pocket-fan.c | 38 "Hysteresis in millicelsius before lowering the fan speed");
100 /* Use hysteresis before lowering speed again */ in gpd_pocket_fan_worker()
|
| /Linux-v6.1/kernel/sched/ |
| D | features.h | 76 * lowering their priorities at the same time, and there being
|
| /Linux-v6.1/Documentation/devicetree/bindings/iio/adc/ |
| D | adi,ad7192.yaml | 66 are unbuffered, lowering the power consumption of the device. If this
|
| /Linux-v6.1/Documentation/x86/ |
| D | tlb.rst | 49 Lowering it to 0 will disable the use of the individual flushes.
|
| /Linux-v6.1/arch/arm/mach-sa1100/ |
| D | sleep.S | 50 @ Adjust memory timing before lowering CPU clock
|
| /Linux-v6.1/drivers/cpufreq/ |
| D | davinci-cpufreq.c | 62 /* if moving to lower freq, lower the voltage after lowering freq */ in davinci_target()
|
| /Linux-v6.1/drivers/net/ethernet/netronome/nfp/nfdk/ |
| D | rings.c | 103 …ate TX descriptor ring memory, requested descriptor count: %d, consider lowering descriptor count\… in nfp_nfdk_tx_ring_alloc()
|
| /Linux-v6.1/tools/testing/selftests/mqueue/ |
| D | mq_open_tests.c | 169 printf("Temporarily lowering default queue parameters " in validate_current_settings()
181 printf("Temporarily lowering maximum queue parameters " in validate_current_settings()
|
| /Linux-v6.1/drivers/net/ethernet/intel/ixgb/ |
| D | ixgb_ee.c | 82 * and then raising and then lowering the clock (the SK bit controls in ixgb_shift_out_bits()
84 * by setting "DI" to "0" and then raising and then lowering the clock. in ixgb_shift_out_bits()
235 * Terminates a command by lowering the EEPROM's chip select pin
|
| /Linux-v6.1/drivers/net/ethernet/netronome/nfp/nfd3/ |
| D | rings.c | 138 …ate TX descriptor ring memory, requested descriptor count: %d, consider lowering descriptor count\… in nfp_nfd3_tx_ring_alloc()
|
| /Linux-v6.1/drivers/crypto/qat/qat_common/ |
| D | adf_pfvf_msg.h | 81 * For both formats, the message reception is acknowledged by lowering the
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn20/ |
| D | dcn20_clk_mgr.c | 323 // if clock is being lowered, increase DTO before lowering refclk in dcn2_update_clocks()
327 // if clock is being raised, increase refclk before lowering DTO in dcn2_update_clocks()
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/ |
| D | dcn30_clk_mgr.c | 304 /* if clock is being lowered, increase DTO before lowering refclk */ in dcn3_update_clocks()
308 /* if clock is being raised, increase refclk before lowering DTO */ in dcn3_update_clocks()
|
| /Linux-v6.1/tools/perf/util/ |
| D | record.c | 213 pr_warning("Lowering default frequency rate from %u to %u.\n" in record_opts__config_freq()
|
| /Linux-v6.1/fs/btrfs/ |
| D | block-group.h | 246 * In mixed mode the fragmentation is expected to be high, lowering the in btrfs_is_block_group_data_only()
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn316/ |
| D | dcn316_clk_mgr.c | 235 // increase per DPP DTO before lowering global dppclk in dcn316_update_clocks()
239 // increase global DPPCLK before lowering per DPP DTO in dcn316_update_clocks()
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | rk3288-veyron-mickey.dts | 113 * - After 696 MHz we stop lowering voltage, so throttling
|
| /Linux-v6.1/arch/arm64/include/asm/ |
| D | ptrace.h | 28 * than the value held in PMR, that IRQ is masked. Lowering the value of PMR
|
| /Linux-v6.1/Documentation/driver-api/media/drivers/ |
| D | zoran.rst | 527 If you experience timeouts, lowering the quality/buffersize or using
538 notes given in question 3 and try lowering quality/buffersize/capturesize
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn315/ |
| D | dcn315_clk_mgr.c | 201 // increase per DPP DTO before lowering global dppclk in dcn315_update_clocks()
205 // increase global DPPCLK before lowering per DPP DTO in dcn315_update_clocks()
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn21/ |
| D | rn_clk_mgr.c | 214 // increase per DPP DTO before lowering global dppclk with requested dppclk in rn_update_clocks()
232 // increase global DPPCLK before lowering per DPP DTO in rn_update_clocks()
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn301/ |
| D | vg_clk_mgr.c | 174 // increase per DPP DTO before lowering global dppclk in vg_update_clocks()
178 // increase global DPPCLK before lowering per DPP DTO in vg_update_clocks()
|
| /Linux-v6.1/drivers/gpu/drm/amd/display/dc/clk_mgr/dcn31/ |
| D | dcn31_clk_mgr.c | 230 // increase per DPP DTO before lowering global dppclk in dcn31_update_clocks()
234 // increase global DPPCLK before lowering per DPP DTO in dcn31_update_clocks()
|
| /Linux-v6.1/drivers/clk/ti/ |
| D | clkt_dpll.c | 92 pr_debug("rejecting n=%d due to Fint failure, lowering max_divider\n", in _dpll_test_fint()
|
| /Linux-v6.1/Documentation/hwmon/ |
| D | it87.rst | 309 try lowering the PWM base frequency (pwm1_freq). Depending on the fan,
|
