Home
last modified time | relevance | path

Searched +full:led +full:- +full:sources (Results 1 – 25 of 81) sorted by relevance

1234

/Linux-v5.15/Documentation/devicetree/bindings/leds/
Dleds-bcm6328.txt7 as spi-gpio. See Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml),
10 exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
13 BCM6328 LED controller has a HWDIS register, which controls whether a LED
16 is usually 1:1 for hardware to LED signals, but through the activity/link
18 explained later in brcm,link-signal-sources). Even if a LED is hardware
21 reason, hardware controlled LEDs aren't registered as LED class devices.
24 - compatible : should be "brcm,bcm6328-leds".
25 - #address-cells : must be 1.
26 - #size-cells : must be 0.
27 - reg : BCM6328 LED controller address and size.
[all …]
Dleds-lm3697.txt1 * Texas Instruments - LM3697 Highly Efficient White LED Driver
3 The LM3697 11-bit LED driver provides high-
5 LED strings while delivering up to 90% efficiency.
10 - compatible:
12 - reg : I2C slave address
13 - #address-cells : 1
14 - #size-cells : 0
17 - enable-gpios : GPIO pin to enable/disable the device
18 - vled-supply : LED supply
21 - reg : 0 - LED is Controlled by bank A
[all …]
Dcommon.yaml1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jacek Anaszewski <jacek.anaszewski@gmail.com>
11 - Pavel Machek <pavel@ucw.cz>
14 LED and flash LED devices provide the same basic functionality as current
15 regulators, but extended with LED and flash LED specific features like
18 Many LED devices expose more than one current output that can be connected
19 to one or more discrete LED component. Since the arrangement of connections
20 can influence the way of the LED device initialization, the LED components
[all …]
Dleds-lm3532.txt1 * Texas Instruments - lm3532 White LED driver with ambient light sensing
4 The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
5 programmable over an I2C-compatible interface and has independent
7 method allows for different LED currents in each current sink thus allowing
11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
16 - compatible : "ti,lm3532"
17 - reg : I2C slave address
18 - #address-cells : 1
19 - #size-cells : 0
22 - enable-gpios : gpio pin to enable (active high)/disable the device.
[all …]
Dleds-lm36274.txt1 * Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias
3 The LM36274 is an integrated four-channel WLED driver and LCD bias supply.
4 The backlight boost provides the power to bias four parallel LED strings with
5 up to 29V total output voltage. The 11-bit LED current is programmable via
9 Documentation/devicetree/bindings/mfd/ti-lmu.txt
12 Documentation/devicetree/bindings/regulator/lm363x-regulator.txt
15 - compatible:
16 "ti,lm36274-backlight"
17 - reg : 0
18 - #address-cells : 1
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/mfd/
Dti-lmu.txt6 ------ ---------------------------------
9 LM3633 Backlight, LED and fault monitor
14 - compatible: Should be one of:
20 - reg: I2C slave address.
28 - enable-gpios: A GPIO specifier for hardware enable pin.
29 - ramp-up-us: Current ramping from one brightness level to
31 Range from 2048 us - 117.44 s
32 - ramp-down-us: Current ramping from one brightness level to
34 Range from 2048 us - 117.44 s
35 - ti,brightness-resolution - This determines whether to use 8 bit brightness
[all …]
Dmax77693.txt1 Maxim MAX77693 multi-function device
4 - PMIC,
5 - CHARGER,
6 - LED,
7 - MUIC,
8 - HAPTIC
14 - compatible : Must be "maxim,max77693".
15 - reg : Specifies the i2c slave address of PMIC block.
16 - interrupts : This i2c device has an IRQ line connected to the main SoC.
19 - regulators : The regulators of max77693 have to be instantiated under subnode
[all …]
Dsky81452.txt4 - compatible : Must be "skyworks,sky81452"
5 - reg : I2C slave address
8 - backlight : container node for backlight following the binding
9 in leds/backlight/sky81452-backlight.txt
10 - regulator : container node for regulators following the binding
11 in regulator/sky81452-regulator.txt
20 compatible = "skyworks,sky81452-backlight";
21 name = "pwm-backlight";
22 led-sources = <0 1 2 3 6>;
23 skyworks,ignore-pwm;
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/leds/backlight/
Dlm3630a-backlight.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/backlight/lm3630a-backlight.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI LM3630A High-Efficiency Dual-String White LED
10 - Lee Jones <lee.jones@linaro.org>
11 - Daniel Thompson <daniel.thompson@linaro.org>
12 - Jingoo Han <jingoohan1@gmail.com>
15 The LM3630A is a current-mode boost converter which supplies the power and
26 '#address-cells':
[all …]
Darcxcnn_bl.txt1 Binding for ArcticSand arc2c0608 LED driver
4 - compatible: should be "arc,arc2c0608"
5 - reg: slave address
8 - default-brightness: brightness value on boot, value from: 0-4095
9 - label: The name of the backlight device
11 - led-sources: List of enabled channels from 0 to 5.
14 - arc,led-config-0: setting for register ILED_CONFIG_0
15 - arc,led-config-1: setting for register ILED_CONFIG_1
16 - arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
17 - arc,comp-config: setting for register CONFIG_COMP
[all …]
Dsky81452-backlight.txt1 SKY81452-backlight bindings
4 - compatible : Must be "skyworks,sky81452-backlight"
7 - name : Name of backlight device. Default is 'lcd-backlight'.
8 - gpios : GPIO to use to EN pin.
10 - led-sources : List of enabled channels from 0 to 5.
12 - skyworks,ignore-pwm : Ignore both PWM input
13 - skyworks,dpwm-mode : Enable DPWM dimming mode, otherwise Analog dimming.
14 - skyworks,phase-shift : Enable phase shift mode
15 - skyworks,short-detection-threshold-volt
17 - skyworks,current-limit-mA
[all …]
/Linux-v5.15/arch/mips/boot/dts/brcm/
Dbcm63268-comtrend-vr-3032u.dts1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
7 compatible = "comtrend,vr-3032u", "brcm,bcm63268";
8 model = "Comtrend VR-3032u";
17 stdout-path = &uart0;
23 brcm,serial-leds;
24 brcm,serial-dat-low;
25 brcm,serial-shift-inv;
27 led@0 {
29 brcm,hardware-controlled;
[all …]
/Linux-v5.15/drivers/video/backlight/
Darcxcnn_bl.c1 // SPDX-License-Identifier: GPL-2.0-only
24 * @leden : initial LED string enables, upper bit is global on/off
48 #define ARCXCNN_CMD_OVP_MASK 0x0C /* --- Over Voltage Threshold */
62 #define ARCXCNN_LEDEN 0x06 /* LED Enable Register */
63 #define ARCXCNN_LEDEN_ISETEXT 0x80 /* Full-scale current set extern */
64 #define ARCXCNN_LEDEN_MASK 0x3F /* LED string enables mask */
65 #define ARCXCNN_LEDEN_BITS 0x06 /* Bits of LED string enables */
73 #define ARCXCNN_WLED_ISET_LSB 0x07 /* LED ISET LSB (in upper nibble) */
75 #define ARCXCNN_WLED_ISET_MSB 0x08 /* LED ISET MSB (8 bits) */
99 ret = i2c_smbus_read_byte_data(lp->client, reg); in arcxcnn_update_field()
[all …]
Dsky81452-backlight.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * sky81452-backlight.c SKY81452 backlight driver
40 #define SKY81452_DEFAULT_NAME "lcd-backlight"
46 * If it is not defined, default name is lcd-backlight.
71 dev_get_platdata(bd->dev.parent); in sky81452_bl_update_status()
72 const unsigned int brightness = (unsigned int)bd->props.brightness; in sky81452_bl_update_status()
77 ret = regmap_write(regmap, SKY81452_REG0, brightness - 1); in sky81452_bl_update_status()
82 pdata->enable << CTZ(SKY81452_EN)); in sky81452_bl_update_status()
119 reg = !strcmp(attr->attr.name, "open") ? SKY81452_REG5 : SKY81452_REG4; in sky81452_bl_show_open_short()
155 strcat(buf, "over-current "); in sky81452_bl_show_fault()
[all …]
/Linux-v5.15/drivers/leds/
Dleds-lm36274.c1 // SPDX-License-Identifier: GPL-2.0
2 // TI LM36274 LED chip family driver
3 // Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
9 #include <linux/leds-ti-lmu-common.h>
15 #include <linux/mfd/ti-lmu.h>
16 #include <linux/mfd/ti-lmu-register.h>
26 * @led_dev: led class device
30 * @led_sources: The LED strings supported in this array
31 * @num_leds: Number of LED strings are supported in this array
49 return ti_lmu_common_set_brightness(&chip->lmu_data, brt_val); in lm36274_brightness_set()
[all …]
Dleds-bcm6328.c1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Driver for BCM6328 memory-mapped LEDs, based on leds-syscon.c
59 * struct bcm6328_led - state container for bcm6328 based LEDs
60 * @cdev: LED class device for this LED
63 * @pin: LED pin number
66 * @active_low: LED is active low
98 * bits [31:0] -> LEDs 8-23
99 * bits [47:32] -> LEDs 0-7
100 * bits [63:48] -> unused
105 return pin + 16; /* LEDs 0-7 (bits 47:32) */ in bcm6328_pin2shift()
[all …]
Dleds-lm3697.c1 // SPDX-License-Identifier: GPL-2.0
2 // TI LM3697 LED chip family driver
3 // Copyright (C) 2018 Texas Instruments Incorporated - https://www.ti.com/
15 #include <linux/leds-ti-lmu-common.h>
47 * struct lm3697_led -
48 * @hvled_strings: Array of LED strings associated with a control bank
49 * @label: LED label
50 * @led_dev: LED class device
53 * @control_bank: Control bank the LED is associated to. 0 is control bank A
55 * @enabled: LED brightness level (or LED_OFF)
[all …]
Dleds-lm3532.c1 // SPDX-License-Identifier: GPL-2.0
2 // TI LM3532 LED driver
3 // Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
16 #define LM3532_NAME "lm3532-led"
123 * @led_dev: led class device
125 * @control_bank: Control bank the LED is associated to
126 * @mode: Mode of the LED string
128 * @num_leds: Number of LED strings are supported in this array
129 * @full_scale_current: The full-scale current setting for the current sink.
130 * @led_strings: The LED strings supported in this array
[all …]
/Linux-v5.15/arch/arm/boot/dts/
Domap4-droid4-xt894.dts1 // SPDX-License-Identifier: GPL-2.0-only
2 /dts-v1/;
4 #include "motorola-mapphone-common.dtsi"
8 compatible = "gpio-keys";
14 linux,can-disable;
16 debounce-interval = <10>;
25 interrupts-extended = <&omap4_pmx_core 0xd6>;
27 linux,input-type = <EV_SW>;
29 linux,can-disable;
31 debounce-interval = <10>;
[all …]
Domap4-droid-bionic-xt875.dts1 // SPDX-License-Identifier: GPL-2.0-only
2 /dts-v1/;
4 #include "motorola-mapphone-common.dtsi"
8 compatible = "motorola,droid-bionic", "ti,omap4430", "ti,omap4";
12 keypad,num-rows = <8>;
13 keypad,num-columns = <8>;
21 led-controller@38 {
23 #address-cells = <1>;
24 #size-cells = <0>;
27 enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
[all …]
De60k02.dtsi1 // SPDX-License-Identifier: GPL-2.0
11 * found in ebook-readers like the Kobo Clara HD (with i.MX6SLL) and
14 #include <dt-bindings/input/input.h>
19 stdout-path = &uart1;
22 gpio_keys: gpio-keys {
23 compatible = "gpio-keys";
29 wakeup-source;
36 linux,input-type = <EV_SW>;
37 wakeup-source;
42 compatible = "gpio-leds";
[all …]
/Linux-v5.15/Documentation/networking/device_drivers/fddi/
Dskfp.rst1 .. SPDX-License-Identifier: GPL-2.0
6 SysKonnect driver - SKFP
9 |copy| Copyright 1998-2000 SysKonnect,
11 skfp.txt created 11-May-2000
53 - SK-5521 (SK-NET FDDI-UP)
54 - SK-5522 (SK-NET FDDI-UP DAS)
55 - SK-5541 (SK-NET FDDI-FP)
56 - SK-5543 (SK-NET FDDI-LP)
57 - SK-5544 (SK-NET FDDI-LP DAS)
58 - SK-5821 (SK-NET FDDI-UP64)
[all …]
/Linux-v5.15/drivers/leds/flash/
Dleds-max77693.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * LED Flash class driver for the flash cell of max77693 mfd.
11 #include <linux/led-class-flash.h>
13 #include <linux/mfd/max77693-common.h>
14 #include <linux/mfd/max77693-private.h>
20 #include <media/v4l2-flash-led-class.h>
59 /* corresponding LED Flash class device */
80 /* sub led data */
96 /* bitmask of FLED outputs use state (bit 0. - FLED1, bit 1. - FLED2) */
109 return (ua - FLASH_IOUT_MIN) / FLASH_IOUT_STEP; in max77693_led_iout_to_reg()
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/net/wireless/
Dmediatek,mt76.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 # Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
5 ---
7 $schema: http://devicetree.org/meta-schemas/core.yaml#
12 - Felix Fietkau <nbd@nbd.name>
13 - Lorenzo Bianconi <lorenzo@kernel.org>
14 - Ryder Lee <ryder.lee@mediatek.com>
24 - $ref: ieee80211.yaml#
29 - mediatek,mt76
30 - mediatek,mt7628-wmac
[all …]
/Linux-v5.15/drivers/usb/core/
Dledtrig-usbport.c1 // SPDX-License-Identifier: GPL-2.0
3 * USB port LED trigger
38 * usbport_trig_usb_dev_observed - Check if dev is connected to observed port
45 if (!usb_dev->parent) in usbport_trig_usb_dev_observed()
48 list_for_each_entry(port, &usbport_data->ports, list) { in usbport_trig_usb_dev_observed()
49 if (usb_dev->parent == port->hub && in usbport_trig_usb_dev_observed()
50 usb_dev->portnum == port->portnum) in usbport_trig_usb_dev_observed()
51 return port->observed; in usbport_trig_usb_dev_observed()
62 usbport_data->count++; in usbport_trig_usb_dev_check()
68 * usbport_trig_update_count - Recalculate amount of connected matching devices
[all …]

1234