Searched full:laser (Results 1 – 25 of 52) sorted by relevance
123
| /Linux-v5.10/Documentation/userspace-api/media/v4l/ |
| D | pixfmt-meta-d4xx.rst | 58 * - __u32 Laser power
59 - Power of the laser LED 0-360, used for depth measurement
75 * - __u32 Laser mode
138 0x00000004 Laser power
185 [2] depthIsActive - has a laser projector
|
| /Linux-v5.10/Documentation/devicetree/bindings/regulator/ |
| D | richtek,rtmv20-regulator.yaml | 7 title: Richtek RTMV20 laser diode regulator
14 It is used to drive laser diode. There're two signals for chip controls
|
| /Linux-v5.10/include/uapi/linux/ |
| D | mdio.h | 305 #define MDIO_PMA_LASI_TX_LASERPOWERFLT 0x0080 /* Laser output power fault */
306 #define MDIO_PMA_LASI_TX_LASERTEMPFLT 0x0100 /* Laser temperature fault */
307 #define MDIO_PMA_LASI_TX_LASERBICURRFLT 0x0200 /* Laser bias current fault */
|
| /Linux-v5.10/drivers/iio/proximity/ |
| D | ping.c | 46 /* pulse width of laser */
176 * read error code of laser ping sensor and give users chance to in ping_read()
|
| D | pulsedlight-lidar-lite-v2.c | 173 /* return -EINVAL since laser is likely pointed out of range */ in lidar_get_measurement()
|
| /Linux-v5.10/include/net/ |
| D | ip6_checksum.h | 9 * Authors: Jorge Cwik, <jorge@laser.satlink.net>
|
| D | checksum.h | 9 * Authors: Jorge Cwik, <jorge@laser.satlink.net>
|
| /Linux-v5.10/drivers/net/ethernet/intel/ixgbe/ |
| D | ixgbe_82599.c | 67 /* enable the laser control functions for SFP+ fiber in ixgbe_init_mac_link_ops_82599()
557 * ixgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser
562 * laser on the PHY, effectively halting physical link.
572 /* Disable tx laser; allow 100us to go dark per spec */ in ixgbe_disable_tx_laser_multispeed_fiber()
580 * ixgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser
585 * laser on the PHY, effectively starting physical link.
591 /* Enable tx laser; allow 100ms to light up */ in ixgbe_enable_tx_laser_multispeed_fiber()
599 * ixgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser
605 * so, we set the speed then disable and re-enable the tx laser, to
|
| /Linux-v5.10/drivers/net/ethernet/chelsio/cxgb/ |
| D | my3126.c | 199 /* Now lets enable the Laser. Delay 100us */ in my3126_phy_reset()
|
| D | mv88x201x.c | 248 /* Now lets enable the Laser. Delay 100us */ in mv88x201x_phy_reset()
|
| /Linux-v5.10/lib/ |
| D | checksum.c | 10 * Authors: Jorge Cwik, <jorge@laser.satlink.net>
|
| /Linux-v5.10/Documentation/networking/device_drivers/ethernet/intel/ |
| D | ixgbe.rst | 98 Laser turns off for SFP+ when ifconfig ethX down
100 "ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters.
101 "ifconfig ethX up" turns on the laser.
103 laser off and on.
|
| /Linux-v5.10/arch/x86/include/asm/ |
| D | checksum_32.h | 62 * By Jorge Cwik <jorge@laser.satlink.net>, adapted for linux by
|
| D | checksum_64.h | 37 * By Jorge Cwik <jorge@laser.satlink.net>, adapted for linux by
|
| /Linux-v5.10/Documentation/ABI/testing/ |
| D | sysfs-driver-hid-roccat-kone | 92 calibrate the laser power to fit the mousepad surface.
|
| /Linux-v5.10/arch/sh/include/asm/ |
| D | checksum_32.h | 82 * i386 version by Jorge Cwik <jorge@laser.satlink.net>, adapted
|
| /Linux-v5.10/drivers/scsi/bfa/ |
| D | bfa_defs.h | 827 SFP_XMTR_TECH_LL = (1 << 3), /* longwave laser */
828 SFP_XMTR_TECH_SL = (1 << 4), /* shortwave laser w/ OFC */
829 SFP_XMTR_TECH_SN = (1 << 5), /* shortwave laser w/o OFC */
832 SFP_XMTR_TECH_LC = (1 << 8), /* longwave laser */
|
| /Linux-v5.10/arch/x86/um/ |
| D | checksum_32.S | 9 * Authors: Jorge Cwik, <jorge@laser.satlink.net>
|
| /Linux-v5.10/arch/mips/include/asm/ |
| D | checksum.h | 94 * By Jorge Cwik <jorge@laser.satlink.net>, adapted for linux by
|
| /Linux-v5.10/arch/sh/lib/ |
| D | checksum.S | 11 * Authors: Jorge Cwik, <jorge@laser.satlink.net>
|
| /Linux-v5.10/drivers/gpu/drm/panel/ |
| D | Kconfig | 29 Zenfone 2 Laser Z00T devices.
|
| /Linux-v5.10/arch/x86/lib/ |
| D | checksum_32.S | 9 * Authors: Jorge Cwik, <jorge@laser.satlink.net>
|
| /Linux-v5.10/arch/m68k/lib/ |
| D | checksum.c | 9 * Authors: Jorge Cwik, <jorge@laser.satlink.net>
|
| /Linux-v5.10/drivers/usb/core/ |
| D | quirks.c | 214 /* Microsoft Wireless Laser Mouse 6000 Receiver */
|
| /Linux-v5.10/net/ipv4/ |
| D | ip_input.c | 15 * Jorge Cwik, <jorge@laser.satlink.net>
|
123
