Searched +full:imx8qxp +full:- +full:mu (Results 1 – 5 of 5) sorted by relevance
| /Linux-v5.10/Documentation/devicetree/bindings/arm/freescale/ |
| D | fsl,scu.txt | 2 --------------------------------------------------------------------
4 The System Controller Firmware (SCFW) is a low-level system function
5 which runs on a dedicated Cortex-M core to provide power, clock, and
9 The AP communicates with the SC using a multi-ported MU module found
10 in the LSIO subsystem. The current definition of this MU module provides
12 (TZ, HV, standard Linux, etc.). The SC side of this MU module interfaces
13 with the LSIO DSC IP bus. The SC firmware will communicate with this MU
22 -------------------
23 - compatible: should be "fsl,imx-scu".
24 - mbox-names: should include "tx0", "tx1", "tx2", "tx3",
[all …]
|
| /Linux-v5.10/arch/arm64/boot/dts/freescale/ |
| D | imx8qxp.dtsi | 1 // SPDX-License-Identifier: GPL-2.0+
4 * Copyright 2017-2018 NXP
8 #include <dt-bindings/clock/imx8-clock.h>
9 #include <dt-bindings/firmware/imx/rsrc.h>
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
13 #include <dt-bindings/pinctrl/pads-imx8qxp.h>
14 #include <dt-bindings/thermal/thermal.h>
17 interrupt-parent = <&gic>;
[all …]
|
| /Linux-v5.10/Documentation/devicetree/bindings/mailbox/ |
| D | fsl,mu.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mailbox/fsl,mu.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: NXP i.MX Messaging Unit (MU)
10 - Dong Aisheng <aisheng.dong@nxp.com>
15 and control) through the MU interface. The MU also provides the ability
18 Because the MU manages the messaging between processors, the MU uses
20 Therefore, the MU must synchronize the accesses from one side to the
21 other. The MU accomplishes synchronization using two sets of matching
[all …]
|
| /Linux-v5.10/Documentation/devicetree/bindings/dsp/ |
| D | fsl,dsp.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Daniel Baluta <daniel.baluta@nxp.com>
14 advanced pre- and post- audio processing.
19 - fsl,imx8qxp-dsp
20 - fsl,imx8qm-dsp
21 - fsl,imx8mp-dsp
28 - description: ipg clock
29 - description: ocram clock
[all …]
|
| /Linux-v5.10/drivers/firmware/imx/ |
| D | scu-pd.c | 1 // SPDX-License-Identifier: GPL-2.0+
4 * Copyright 2017-2018 NXP
10 * single global power domain and implement the ->attach|detach_dev()
12 * From within the ->attach_dev(), we could get the OF node for
13 * the device that is being attached and then parse the power-domain
18 * Additionally, we need to implement the ->stop() and ->start()
20 * rather than using the above ->power_on|off() callbacks.
23 * 1. The ->attach_dev() of power domain infrastructure still does
33 * behavior changed if removing ->power_on|off() callback and use
34 * ->start() and ->stop() instead. genpd_dev_pm_attach will only power
[all …]
|
