Searched full:i2c4 (Results 1 – 25 of 491) sorted by relevance
12345678910>>...20
| /Linux-v6.1/arch/arm64/boot/dts/renesas/ |
| D | r8a779f0-spider-cpu.dtsi | 62 &i2c4 {
102 i2c4_pins: i2c4 {
103 groups = "i2c4";
104 function = "i2c4";
|
| D | r8a774a1-beacon-rzg2m-kit.dts | 21 i2c4 = &i2c4;
|
| D | hihope-common.dtsi | 17 i2c4 = &i2c4;
191 &i2c4 {
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts | 15 i2c0 = &i2c4;
21 i2c-bus = <&i2c4>;
59 i2c4: i2c@600 { label
|
| D | uniphier-pinctrl.dtsi | 104 pinctrl_i2c4: i2c4 {
105 groups = "i2c4";
106 function = "i2c4";
|
| D | r8a7794-alt.dts | 227 * I2C4 is routed to EXIO connector B, pins 73 (SCL) + 74 (SDA).
232 i2c-parent = <&i2c4>, <&gpioi2c4>;
311 i2c4_pins: i2c4 {
312 groups = "i2c4";
313 function = "i2c4";
446 &i2c4 {
|
| D | twl4030_omap3.dtsi | 25 * If your board is not using the I2C4 pins with twl4030, then don't include
27 * pins we need to configure I2C4, or else use the legacy sys_nvmode1 and
|
| D | uniphier-ld6b-ref.dts | 30 i2c4 = &i2c4;
|
| D | uniphier-pxs2-vodka.dts | 24 i2c4 = &i2c4;
|
| D | uniphier-pxs2-gentil.dts | 26 i2c4 = &i2c4;
|
| D | r8a77470-iwg23s-sbc.dts | 144 &i2c4 {
193 i2c4_pins: i2c4 {
195 function = "i2c4";
|
| D | nuvoton-npcm730-gsj.dts | 20 i2c4 = &i2c4;
248 &i2c4 {
|
| /Linux-v6.1/arch/arm64/boot/dts/socionext/ |
| D | uniphier-ld11-ref.dts | 30 i2c4 = &i2c4;
|
| D | uniphier-ld20-ref.dts | 30 i2c4 = &i2c4;
|
| D | uniphier-ld11-global.dts | 31 i2c4 = &i2c4;
|
| D | uniphier-ld20-akebi96.dts | 32 i2c4 = &i2c4;
|
| D | uniphier-ld20-global.dts | 31 i2c4 = &i2c4;
|
| /Linux-v6.1/arch/arm64/boot/dts/toshiba/ |
| D | tmpv7708_pins.dtsi | 68 i2c4_pins: i2c4-pins {
69 function = "i2c4";
|
| /Linux-v6.1/Documentation/devicetree/bindings/pinctrl/ |
| D | cirrus,lochnagar.yaml | 108 i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl, i2c4-sda,
136 i2c2-scl, i2c2-sda, i2c3-scl, i2c3-sda, i2c4-scl,
137 i2c4-sda, spdif-aif, psia1, psia1-bclk, psia1-lrclk,
|
| /Linux-v6.1/arch/arm64/boot/dts/mediatek/ |
| D | mt8195-evb.dts | 45 &i2c4 {
92 i2c4_pin: i2c4-pins {
|
| D | mt8186-evb.dts | 60 &i2c4 {
149 i2c4_pins: i2c4-default-pins {
|
| /Linux-v6.1/arch/arm64/boot/dts/rockchip/ |
| D | rk3566-soquartz-cm4.dts | 74 * i2c4 is exposed on CM2 / Module1B - to PI40
78 &i2c4 {
|
| /Linux-v6.1/arch/arm/mach-omap2/ |
| D | vc.c | 350 * By default let's use I2C4 signaling for retention idle in omap3_vc_init_pmic_signaling()
396 * retention signaled over I2C4, so we can keep voltsetup2 as 0.
397 * And the oscillator is not shut off over I2C4, so no need to
404 /* Configure PRWDM_POWER_OFF over I2C4 */ in omap3_set_i2c_timings()
407 /* Configure PRWDM_POWER_RET over I2C4 */ in omap3_set_i2c_timings()
759 * Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)". in omap_vc_i2c_init()
760 * Otherwise I2C4 eventually leads into about 23mW extra power being in omap_vc_i2c_init()
|
| /Linux-v6.1/arch/arm64/boot/dts/freescale/ |
| D | imx8mq-nitrogen.dts | 213 &i2c4 {
225 i2c4@0 {
260 ddc_i2c_bus: i2c4@1 {
267 i2c4@3 {
|
| /Linux-v6.1/arch/mips/boot/dts/ingenic/ |
| D | ci20.dts | 339 &i2c4 {
521 pins_i2c4: i2c4 {
522 function = "i2c4";
523 groups = "i2c4-data-e";
|
12345678910>>...20
