| /Linux-v6.1/Documentation/devicetree/bindings/phy/ |
| D | qcom,usb-hsic-phy.txt | 1 Qualcomm's USB HSIC PHY
8 Definition: Should contain "qcom,usb-hsic-phy" and more specifically one of the
11 "qcom,usb-hsic-phy-mdm9615"
12 "qcom,usb-hsic-phy-msm8974"
38 Definition: List of pinctrl settings to apply to keep HSIC pins in a glitch
44 Definition: List of pinctrl settings to apply to mux out the HSIC pins
51 compatible = "qcom,usb-hsic-phy-msm8974",
52 "qcom,usb-hsic-phy";
|
| D | nvidia,tegra124-xusb-padctl.txt | 13 or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller
65 - vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
83 For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie
86 For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is
97 HSIC pad:
103 - "trk": phandle and specifier referring to the HSIC tracking clock
146 - hsic: hsic-0, hsic-1
156 - hsic: hsic-0, hsic-1
212 HSIC ports:
250 - 2x HSIC: hsic-0, hsic-1
[all …]
|
| D | allwinner,sun9i-a80-usb-phy.yaml | 30 - description: HSIC 12MHz clock
31 - description: HSIC 480MHz clock
46 - description: HSIC Reset
52 - const: hsic
55 const: hsic
77 const: hsic
128 "hsic";
129 phy_type = "hsic";
|
| D | marvell,mmp3-hsic-phy.yaml | 5 $id: "http://devicetree.org/schemas/phy/marvell,mmp3-hsic-phy.yaml#"
8 title: Marvell MMP3 HSIC PHY
15 const: marvell,mmp3-hsic-phy
33 hsic-phy@f0001800 {
34 compatible = "marvell,mmp3-hsic-phy";
|
| D | pxa1928-usb-phy.txt | 1 * Marvell PXA1928 USB and HSIC PHYs
4 - compatible: "marvell,pxa1928-usb-phy" or "marvell,pxa1928-hsic-phy"
|
| /Linux-v6.1/drivers/phy/samsung/ |
| D | phy-exynos5250-usb2.c | 202 u32 hsic; in exynos5250_power_on() local
286 /* HSIC phy configuration */ in exynos5250_power_on()
287 hsic = (EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_12 | in exynos5250_power_on()
290 writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL1); in exynos5250_power_on()
291 writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL2); in exynos5250_power_on()
293 hsic &= ~EXYNOS_5250_HSICPHYCTRLX_PHYSWRST; in exynos5250_power_on()
294 writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL1); in exynos5250_power_on()
295 writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL2); in exynos5250_power_on()
326 u32 hsic; in exynos5250_power_off() local
349 hsic = (EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_12 | in exynos5250_power_off()
[all …]
|
| /Linux-v6.1/Documentation/devicetree/bindings/mfd/ |
| D | omap-usb-host.txt | 20 "ehci-hsic",
51 * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate.
52 * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate.
53 * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate.
54 * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate.
55 * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate.
56 * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate.
|
| /Linux-v6.1/drivers/phy/tegra/ |
| D | xusb-tegra124.c | 807 TEGRA124_LANE("hsic-0", 0x004, 14, 0x1, hsic),
808 TEGRA124_LANE("hsic-1", 0x004, 15, 0x1, hsic),
815 struct tegra_xusb_hsic_lane *hsic; in tegra124_hsic_lane_probe() local
818 hsic = kzalloc(sizeof(*hsic), GFP_KERNEL); in tegra124_hsic_lane_probe()
819 if (!hsic) in tegra124_hsic_lane_probe()
822 INIT_LIST_HEAD(&hsic->base.list); in tegra124_hsic_lane_probe()
823 hsic->base.soc = &pad->soc->lanes[index]; in tegra124_hsic_lane_probe()
824 hsic->base.index = index; in tegra124_hsic_lane_probe()
825 hsic->base.pad = pad; in tegra124_hsic_lane_probe()
826 hsic->base.np = np; in tegra124_hsic_lane_probe()
[all …]
|
| D | xusb.c | 291 if (strcmp(soc->name, "hsic") == 0) in tegra_xusb_pad_create()
292 padctl->hsic = pad; in tegra_xusb_pad_create()
874 static int tegra_xusb_hsic_port_parse_dt(struct tegra_xusb_hsic_port *hsic) in tegra_xusb_hsic_port_parse_dt() argument
883 struct tegra_xusb_hsic_port *hsic; in tegra_xusb_add_hsic_port() local
887 np = tegra_xusb_find_port_node(padctl, "hsic", index); in tegra_xusb_add_hsic_port()
891 hsic = kzalloc(sizeof(*hsic), GFP_KERNEL); in tegra_xusb_add_hsic_port()
892 if (!hsic) { in tegra_xusb_add_hsic_port()
897 err = tegra_xusb_port_init(&hsic->base, padctl, np, "hsic", index); in tegra_xusb_add_hsic_port()
901 hsic->base.ops = padctl->soc->ports.hsic.ops; in tegra_xusb_add_hsic_port()
903 hsic->base.lane = hsic->base.ops->map(&hsic->base); in tegra_xusb_add_hsic_port()
[all …]
|
| D | xusb-tegra210.c | 1604 /* save state, HSIC always comes up as HS */ in tegra210_pmc_hsic_enable_phy_sleepwalk()
1625 * stages of sleepwalk. Maintain a HSIC IDLE and keep driving HSIC in tegra210_pmc_hsic_enable_phy_sleepwalk()
2248 TEGRA210_LANE("hsic-0", 0x004, 14, 0x1, hsic),
2255 struct tegra_xusb_hsic_lane *hsic; in tegra210_hsic_lane_probe() local
2258 hsic = kzalloc(sizeof(*hsic), GFP_KERNEL); in tegra210_hsic_lane_probe()
2259 if (!hsic) in tegra210_hsic_lane_probe()
2262 INIT_LIST_HEAD(&hsic->base.list); in tegra210_hsic_lane_probe()
2263 hsic->base.soc = &pad->soc->lanes[index]; in tegra210_hsic_lane_probe()
2264 hsic->base.index = index; in tegra210_hsic_lane_probe()
2265 hsic->base.pad = pad; in tegra210_hsic_lane_probe()
[all …]
|
| /Linux-v6.1/drivers/phy/marvell/ |
| D | phy-pxa-28nm-hsic.c | 80 dev_err(&pdev->dev, "HSIC PHY PLL not locked after 100mS."); in mv_hsic_phy_init()
98 reg |= PHY_28NM_HSIC_S2H_HSIC_EN; /* Enable HSIC PHY */ in mv_hsic_phy_power_on()
114 dev_warn(&pdev->dev, "HSIC PHY READY not set after 100mS."); in mv_hsic_phy_power_on()
118 /* Waiting for HSIC connect int*/ in mv_hsic_phy_power_on()
122 dev_warn(&pdev->dev, "HSIC wait for connect interrupt timeout."); in mv_hsic_phy_power_on()
193 { .compatible = "marvell,pxa1928-hsic-phy", },
201 .name = "mv-hsic-phy",
208 MODULE_DESCRIPTION("Marvell HSIC phy driver");
|
| D | Kconfig | 85 tristate "Marvell USB HSIC 28nm PHY Driver"
89 Enable this to support Marvell USB HSIC PHY driver for Marvell
129 tristate "Marvell MMP3 USB HSIC PHY Driver"
133 Enable this to support Marvell MMP3 USB HSIC PHY driver for
135 driver to initialize the interface to internal USB HSIC
|
| D | phy-mmp3-hsic.c | 35 { .compatible = "marvell,mmp3-hsic-phy", },
72 .name = "mmp3-hsic-phy",
79 MODULE_DESCRIPTION("Marvell MMP3 USB HSIC PHY Driver");
|
| D | Makefile | 6 obj-$(CONFIG_PHY_MMP3_HSIC) += phy-mmp3-hsic.o
13 obj-$(CONFIG_PHY_PXA_28NM_HSIC) += phy-pxa-28nm-hsic.o
|
| /Linux-v6.1/Documentation/devicetree/bindings/usb/ |
| D | nvidia,tegra124-xusb.txt | 80 - Tegra124: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1
81 - Tegra132: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1
82 - Tegra210: usb2-0, usb2-1, usb2-2, usb2-3, hsic-0, usb3-0, usb3-1, usb3-2,
84 - Tegra186: usb2-0, usb2-1, usb2-2, hsic-0, usb3-0, usb3-1, usb3-2
|
| D | ci-hdrc-usb2.txt | 27 of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this
89 In case of HSIC-mode, "idle" and "active" pin modes are mandatory. In this
134 Example for HSIC:
143 phy_type = "hsic";
|
| D | usb.yaml | 38 serial is specified and High-Speed Inter-Chip feature if HSIC is
42 enum: [utmi, utmi_wide, ulpi, serial, hsic]
|
| /Linux-v6.1/drivers/phy/qualcomm/ |
| D | phy-qcom-usb-hsic.c | 55 /* Configure pins for HSIC functionality */ in qcom_usb_hsic_phy_power_on()
66 /* Enable HSIC mode in HSIC_CFG register */ in qcom_usb_hsic_phy_power_on()
143 { .compatible = "qcom,usb-hsic-phy", },
157 MODULE_DESCRIPTION("Qualcomm USB HSIC phy");
|
| /Linux-v6.1/drivers/usb/chipidea/ |
| D | ci_hdrc_imx.h | 24 unsigned int hsic:1; /* HSIC controller */ member
|
| D | ci_hdrc_msm.c | 44 bool hsic; member
113 if (!msm_ci->hsic) in ci_hdrc_msm_notify_event()
248 ci->hsic = of_device_is_compatible(phy_node, "qcom,usb-hsic-phy"); in ci_hdrc_msm_probe()
|
| D | usbmisc_imx.c | 80 /* HSIC enable */
82 /* Force HSIC module 480M clock on, even when in Host is in suspend mode */
448 /* For HSIC controller */ in usbmisc_imx6q_init()
449 if (data->hsic) { in usbmisc_imx6q_init()
477 * the first two USB controllers are non-HSIC controllers. in usbmisc_imx6_hsic_get_reg_offset()
565 /* For HSIC controller */ in usbmisc_imx6sx_init()
566 if (data->hsic) { in usbmisc_imx6sx_init()
652 if (!data->hsic) { in usbmisc_imx7d_init()
911 if (data->hsic) { in usbmisc_imx7ulp_init()
920 * For non-HSIC controller, the autoresume is enabled in usbmisc_imx7ulp_init()
[all …]
|
| /Linux-v6.1/drivers/clk/sunxi-ng/ |
| D | ccu-sun9i-a80-usb.c | 32 static SUNXI_CCU_GATE_DATA(usb1_hsic_clk, "usb1-hsic", clk_parent_hosc, 0x4, BIT(2), 0);
34 static SUNXI_CCU_GATE_DATA(usb2_hsic_clk, "usb2-hsic", clk_parent_hosc, 0x4, BIT(4), 0);
36 static SUNXI_CCU_GATE_DATA(usb_hsic_clk, "usb-hsic", clk_parent_hosc, 0x4, BIT(10), 0);
|
| /Linux-v6.1/drivers/pinctrl/tegra/ |
| D | pinctrl-tegra-xusb.c | 717 PINCTRL_PIN(PIN_HSIC_0, "hsic-0"),
718 PINCTRL_PIN(PIN_HSIC_1, "hsic-1"),
732 "hsic-0",
733 "hsic-1",
741 "hsic-0",
742 "hsic-1",
843 TEGRA124_LANE("hsic-0", 0x004, 14, 0x1, 0, usb),
844 TEGRA124_LANE("hsic-1", 0x004, 15, 0x1, 0, usb),
|
| /Linux-v6.1/drivers/usb/misc/ |
| D | Kconfig | 257 tristate "USB3503 HSIC to USB20 Driver"
261 This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver.
264 tristate "USB4604 HSIC to USB20 Driver"
267 This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver.
|
| /Linux-v6.1/drivers/gpu/drm/bridge/ |
| D | sil-sii8620.h | 338 /* HSIC RX Control3, default value: 0x07 */
345 /* HSIC RX INT Registers */
417 /* HSIC TX CRTL, default value: 0x00 */
425 /* HSIC TX INT Low, default value: 0x00 */
428 /* HSIC TX INT High, default value: 0x00 */
431 /* HSIC Keeper, default value: 0x00 */
437 /* HSIC Flow Control General, default value: 0x02 */
442 /* HSIC Flow Control CTR13, default value: 0xfc */
445 /* HSIC Flow Control CTR14, default value: 0xff */
448 /* HSIC Flow Control CTR15, default value: 0xff */
[all …]
|
