| /Linux-v6.1/drivers/net/wwan/iosm/ |
| D | iosm_ipc_devlink.h | 87 * @channel_id: Reserved channel id for flashing/CD collection to RAM
88 * @channel: Channel instance for flashing and coredump
100 * struct iosm_flash_params - List of flash params required for flashing
101 * @erase_full_flash: To set the flashing mode
130 * struct iosm_ebl_ctx_data - EBL ctx data used during flashing
159 * @param: Params required for flashing
|
| D | iosm_ipc_flash.h | 63 * enum iosm_flash_package_type - Enum for the flashing operations
67 * @FLASH_SET_ADDRESS: Set the address for flashing
68 * @FLASH_ERASE_START: Start erase before flashing
|
| D | iosm_ipc_devlink.c | 124 devlink_flash_update_status_notify(devlink, "Flashing success", in ipc_devlink_flash_update()
127 devlink_flash_update_status_notify(devlink, "Flashing failed", in ipc_devlink_flash_update()
|
| D | iosm_ipc_flash.c | 103 /* Allocate channel for flashing/cd collection */ in ipc_flash_link_establish()
329 /* Logic for flashing all the Loadmaps available for individual fls file */
|
| D | iosm_ipc_imem.h | 284 * @IPC_P_RUN: The phase after flashing to RAM is the RUNTIME phase.
593 * flashing to RAM interworking shall be
|
| /Linux-v6.1/Documentation/networking/devlink/ |
| D | iosm.rst | 26 the device during firmware flashing.
59 each having one secure bin file and at least one Loadmap/Region file. For flashing
61 data required for flashing. The data like region count and address of each region
64 If the device has to be fully erased before firmware flashing, user application
84 4) Once EBL is injected successfully, then the actual firmware flashing takes
91 b) Flashing the Loadmap/Region file
|
| /Linux-v6.1/Documentation/scsi/ |
| D | ChangeLog.ips | 13 4.90.08 - Increase Delays in Flashing ( Trombone Only - 4H )
51 4.70.09 - Use a Common ( Large Buffer ) for Flashing from the JCRM CD
|
| /Linux-v6.1/drivers/net/ethernet/mellanox/mlxfw/ |
| D | Kconfig | 10 flashing common logic.
|
| D | mlxfw_fsm.c | 336 mlxfw_info(mlxfw_dev, "Flashing component type %d\n", in mlxfw_flash_components()
|
| /Linux-v6.1/Documentation/devicetree/bindings/phy/ |
| D | phy-mapphone-mdm6600.txt | 9 normal mode versus USB flashing mode
|
| /Linux-v6.1/Documentation/devicetree/bindings/input/ |
| D | pine64,pinephone-keyboard.yaml | 14 It connects via I2C, providing a raw scan matrix, a flashing interface, and a
|
| /Linux-v6.1/Documentation/admin-guide/ |
| D | svga.rst | 66 Enter mode number or ``scan``: <flashing-cursor-here>
78 <flashing-cursor-here> encourages you to enter the item number or mode ID
97 what happens then. The screen will be probably flashing wildly for some time and
|
| /Linux-v6.1/Documentation/devicetree/bindings/mtd/partitions/ |
| D | brcm,bcm4908-partitions.yaml | 14 firmware. System can use that information e.g. for booting or flashing
|
| D | linksys,ns-partitions.yaml | 15 firmware. System can use that information e.g. for booting or flashing
|
| /Linux-v6.1/drivers/platform/x86/ |
| D | intel_scu_ipcutil.c | 75 * Support the I/O and firmware flashing interfaces of the SCU
|
| /Linux-v6.1/drivers/staging/greybus/ |
| D | arche-apb-ctrl.c | 154 /* for flashing device should be in reset state */ in fw_flashing_seq()
283 * and then enter FW flashing state in state_store()
|
| /Linux-v6.1/drivers/net/ethernet/intel/ice/ |
| D | ice_fw_update.c | 413 devlink_flash_update_status_notify(devlink, "Flashing", in ice_write_nvm_module()
440 devlink_flash_update_status_notify(devlink, "Flashing", in ice_write_nvm_module()
447 devlink_flash_update_status_notify(devlink, "Flashing failed", in ice_write_nvm_module()
450 devlink_flash_update_status_notify(devlink, "Flashing done", in ice_write_nvm_module()
|
| /Linux-v6.1/drivers/phy/motorola/ |
| D | phy-mapphone-mdm6600.c | 77 PHY_MDM6600_STATUS_RAM_DOWNLOADER, /* MDM6600 USB flashing mode */
388 * to configure USB flashing mode later on based on a module in phy_mdm6600_device_power_on()
|
| /Linux-v6.1/drivers/net/ethernet/sfc/ |
| D | ethtool.c | 32 /* Identify device by flashing LEDs */
|
| /Linux-v6.1/drivers/net/ethernet/sfc/siena/ |
| D | ethtool.c | 32 /* Identify device by flashing LEDs */
|
| /Linux-v6.1/arch/powerpc/kernel/ |
| D | rtas_flash.c | 323 /* In the case that the image is not ready for flashing, the memory in rtas_flash_write()
627 rtas_progress("Flashing \n", 0x0); in rtas_flash_firmware()
|
| /Linux-v6.1/drivers/net/ethernet/cavium/liquidio/ |
| D | liquidio_common.h | 697 u64 flashing:1; member
703 u64 flashing:1;
|
| /Linux-v6.1/drivers/net/netdevsim/ |
| D | dev.c | 1030 devlink_flash_update_status_notify(devlink, "Flashing", in nsim_dev_flash_update()
1038 devlink_flash_update_status_notify(devlink, "Flashing", in nsim_dev_flash_update()
1044 devlink_flash_update_status_notify(devlink, "Flashing done", in nsim_dev_flash_update()
|
| /Linux-v6.1/drivers/mtd/maps/ |
| D | amd76xrom.c | 52 * This is intended to prevent flashing the bios, perhaps accidentally.
|
| D | ck804xrom.c | 58 * This is intended to prevent flashing the bios, perhaps accidentally.
|
