| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | tps65132-regulator.txt | 17 -active-discharge-gpios: (active high, output) Some configurations use delay mechanisms
19 the enable signal goes low. This GPIO is used to actively discharge
20 the delay mechanism. Requires specification of ti,active-discharge-time-us
21 -ti,active-discharge-time-us: how long the active discharge gpio should be
22 asserted for during active discharge, in microseconds.
43 regulator-active-discharge = <0>;
|
| D | ti,tps62360.yaml | 49 ti,enable-vout-discharge:
50 description: Enable output discharge.
94 ti,enable-vout-discharge;
|
| D | maxim,max8973.yaml | 61 maxim,enable-active-discharge:
63 description: Eable active discharge.
135 maxim,enable-active-discharge;
|
| D | qcom-labibb-regulator.yaml | 52 qcom,discharge-resistor-kohms:
54 description: Discharge resistor value in KiloOhms.
|
| D | regulator.yaml | 203 regulator-active-discharge:
205 tristate, enable/disable active discharge of regulators. The values are:
206 0: Disable active discharge.
207 1: Enable active discharge.
|
| /Linux-v6.1/drivers/regulator/ |
| D | tps65132-regulator.c | 73 /* Hardware automatically enable discharge bit in enable */ in tps65132_regulator_enable()
78 dev_err(tps->dev, "Failed to disable active discharge: %d\n", in tps65132_regulator_enable()
153 "active-discharge", in tps65132_of_parse_cb()
155 "active-discharge"); in tps65132_of_parse_cb()
166 ret = of_property_read_u32(np, "ti,active-discharge-time-us", in tps65132_of_parse_cb()
169 dev_err(tps->dev, "Failed to read active discharge time:%d\n", in tps65132_of_parse_cb()
|
| D | tps62360-regulator.c | 250 /* Reset output discharge path to reduce power consumption */ in tps62360_init_dcdc()
308 if (of_find_property(np, "ti,enable-vout-discharge", NULL)) in of_get_tps62360_platform_data()
477 /* Configure the output discharge path */ in tps62360_shutdown()
|
| /Linux-v6.1/Documentation/devicetree/bindings/display/ |
| D | repaper.txt | 10 - discharge-gpios: Discharge control
47 discharge-gpios = <&gpio 15 0>;
|
| /Linux-v6.1/include/sound/ |
| D | wm2200.h | 39 unsigned int discharge:1; /** Actively discharge */ member
|
| D | da7218.h | 80 bool discharge; member
|
| /Linux-v6.1/Documentation/devicetree/bindings/power/supply/ |
| D | dlg,da9150-fuel-gauge.yaml | 27 description: Battery discharge level (%) where warning event raised.
34 Battery discharge level (%) where critical event raised.
|
| D | x-powers,axp20x-battery-power-supply.yaml | 10 The supported devices can read the battery voltage, charge and discharge
|
| /Linux-v6.1/include/linux/mfd/wm8350/ |
| D | audio.h | 596 int vmid_discharge_msecs; /* VMID --> OFF discharge time */
598 int cap_discharge_msecs; /* Cap ON (from OFF) discharge time */
601 u32 dis_out4:2; /* out4 discharge speed */
602 u32 dis_out3:2; /* out3 discharge speed */
603 u32 dis_out2:2; /* out2 discharge speed */
604 u32 dis_out1:2; /* out1 discharge speed */
|
| /Linux-v6.1/drivers/gpu/drm/tiny/ |
| D | repaper.c | 73 struct gpio_desc *discharge; member
618 /* Discharge pulse */ in power_off()
619 gpiod_set_value_cansleep(epd->discharge, 1); in power_off()
621 gpiod_set_value_cansleep(epd->discharge, 0); in power_off()
651 gpiod_set_value_cansleep(epd->discharge, 0); in repaper_pipe_enable()
818 /* Discharge internal */ in repaper_pipe_disable()
989 epd->discharge = devm_gpiod_get(dev, "discharge", GPIOD_OUT_LOW); in repaper_probe()
990 if (IS_ERR(epd->discharge)) { in repaper_probe()
991 ret = PTR_ERR(epd->discharge); in repaper_probe()
993 DRM_DEV_ERROR(dev, "Failed to get gpio 'discharge'\n"); in repaper_probe()
|
| /Linux-v6.1/Documentation/devicetree/bindings/sound/ |
| D | da7218.txt | 64 - dlg,discharge : Boolean flag, auto discharge of Mic Bias on jack removal
|
| /Linux-v6.1/include/linux/mfd/arizona/ |
| D | pdata.h | 61 unsigned int discharge:1; /** Actively discharge */ member
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | stm32mp15xx-osd32.dtsi | 177 regulator-active-discharge = <1>;
183 regulator-active-discharge = <1>;
|
| D | stm32mp15xx-dhcor-som.dtsi | 194 regulator-active-discharge = <1>;
200 regulator-active-discharge = <1>;
|
| D | stm32mp157a-stinger96.dtsi | 219 regulator-active-discharge = <1>;
225 regulator-active-discharge = <1>;
|
| /Linux-v6.1/include/linux/regulator/ |
| D | tps62360.h | 19 * @en_discharge: Enable discharge the output capacitor via internal
|
| D | machine.h | 52 /* Regulator active discharge flags */
152 * @active_discharge: Enable/disable active discharge. The enum
|
| /Linux-v6.1/Documentation/devicetree/bindings/display/panel/ |
| D | samsung,lms380kf01.yaml | 28 description: provides an optional ESD (electrostatic discharge)
|
| D | samsung,s6d27a1.yaml | 26 description: provides an optional ESD (electrostatic discharge)
|
| /Linux-v6.1/arch/arm/mach-pxa/ |
| D | poodle.h | 49 #define POODLE_GPIO_DISCHARGE_ON (42) /* Enable battery discharge */
|
| D | sharpsl_pm.h | 18 void (*discharge)(int); member
|
