Searched full:dirout (Results 1 – 12 of 12) sorted by relevance
| /Linux-v5.15/Documentation/devicetree/bindings/gpio/ |
| D | brcm,bcm6345-gpio.yaml | 19 BCM6338 have 8-bit data and dirout registers, where GPIO state can be read
21 BCM6345 have 16-bit data and dirout registers, where GPIO state can be read
24 and dirout registers, where GPIO state can be read and/or written, and the
53 - const: dirout
69 reg-names = "dirout", "dat";
80 reg-names = "dirout", "dat";
|
| /Linux-v5.15/drivers/gpio/ |
| D | gpio-mmio.c | 483 * - an output direction register (named "dirout") where a 1 bit
540 void __iomem *dirout, in bgpio_setup_direction() argument
544 if (dirout || dirin) { in bgpio_setup_direction()
545 gc->reg_dir_out = dirout; in bgpio_setup_direction()
588 * @dirout: MMIO address for the register to set the line as OUTPUT. It is assumed
601 void __iomem *clr, void __iomem *dirout, void __iomem *dirin, in bgpio_init() argument
629 ret = bgpio_setup_direction(gc, dirout, dirin, flags); in bgpio_init()
731 void __iomem *dirout; in bgpio_pdev_probe() local
766 dirout = bgpio_map(pdev, "dirout", sz); in bgpio_pdev_probe()
767 if (IS_ERR(dirout)) in bgpio_pdev_probe()
[all …]
|
| D | gpio-dwapb.c | 490 void __iomem *dat, *set, *dirout; in dwapb_gpio_add_port() local
505 dirout = gpio->regs + GPIO_SWPORTA_DDR + pp->idx * GPIO_SWPORT_DDR_STRIDE; in dwapb_gpio_add_port()
508 err = bgpio_init(&port->gc, gpio->dev, 4, dat, set, NULL, dirout, in dwapb_gpio_add_port()
|
| D | gpio-amd8111.c | 136 dev_dbg(&agp->pdev->dev, "Dirout gpio %d, value %d, reg=%02x\n", offset, !!value, temp); in amd_gpio_dirout()
|
| /Linux-v5.15/Documentation/devicetree/bindings/mfd/ |
| D | brcm,bcm6358-gpio-sysctl.yaml | 73 reg-names = "dirout", "dat";
|
| D | brcm,bcm6328-gpio-sysctl.yaml | 73 reg-names = "dirout", "dat";
|
| D | brcm,bcm6318-gpio-sysctl.yaml | 73 reg-names = "dirout", "dat";
|
| D | brcm,bcm63268-gpio-sysctl.yaml | 73 reg-names = "dirout", "dat";
|
| D | brcm,bcm6362-gpio-sysctl.yaml | 73 reg-names = "dirout", "dat";
|
| D | brcm,bcm6368-gpio-sysctl.yaml | 73 reg-names = "dirout", "dat";
|
| /Linux-v5.15/arch/arm64/boot/dts/broadcom/bcm4908/ |
| D | bcm4908.dtsi | 283 reg-names = "dirout", "dat";
|
| /Linux-v5.15/include/linux/gpio/ |
| D | driver.h | 608 void __iomem *clr, void __iomem *dirout, void __iomem *dirin,
|
