Home
last modified time | relevance | path

Searched +full:debounce +full:- +full:delay +full:- +full:ms (Results 1 – 25 of 87) sorted by relevance

1234

/Linux-v5.15/Documentation/devicetree/bindings/input/
Dlpc32xx-key.txt3 This binding is based on the matrix-keymap binding with the following
7 - compatible: Should be "nxp,lpc3220-key"
8 - reg: Physical base address of the controller and length of memory mapped
10 - interrupts: The interrupt number to the cpu.
11 - clocks: phandle to clock controller plus clock-specifier pair
12 - nxp,debounce-delay-ms: Debounce delay in ms
13 - nxp,scan-delay-ms: Repeated scan period in ms
14 - linux,keymap: the key-code to be reported when the key is pressed
16 Documentation/devicetree/bindings/input/matrix-keymap.txt
18 Note: keypad,num-rows and keypad,num-columns are required, and must be equal
[all …]
Dgpio-matrix-keypad.txt6 keypad can sense a key-press and key-release by means of GPIO lines and
10 - compatible: Should be "gpio-matrix-keypad"
11 - row-gpios: List of gpios used as row lines. The gpio specifier
14 - col-gpios: List of gpios used as column lines. The gpio specifier
17 - linux,keymap: The definition can be found at
18 bindings/input/matrix-keymap.txt
21 - linux,no-autorepeat: do no enable autorepeat feature.
22 - wakeup-source: use any event on keypad as wakeup event.
24 - debounce-delay-ms: debounce interval in milliseconds
25 - col-scan-delay-us: delay, measured in microseconds, that is needed
[all …]
Dnvidia,tegra20-kbc.txt7 - compatible: "nvidia,tegra20-kbc"
8 - reg: Register base address of KBC.
9 - interrupts: Interrupt number for the KBC.
10 - nvidia,kbc-row-pins: The KBC pins which are configured as row. This is an
12 - nvidia,kbc-col-pins: The KBC pins which are configured as column. This is an
14 - linux,keymap: The keymap for keys as described in the binding document
15 devicetree/bindings/input/matrix-keymap.txt.
16 - clocks: Must contain one entry, for the module clock.
17 See ../clocks/clock-bindings.txt for details.
18 - resets: Must contain an entry for each entry in reset-names.
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/mfd/
Dtc3589x.txt1 * Toshiba TC3589x multi-purpose expander
3 The Toshiba TC3589x series are I2C-based MFD devices which may expose the
4 following built-in devices: gpio, keypad, rotator (vibrator), PWM (for
7 - TC35890
8 - TC35892
9 - TC35893
10 - TC35894
11 - TC35895
12 - TC35896
15 - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893",
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/auxdisplay/
Dholtek,ht16k33.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Robin van der Gracht <robin@protonic.nl>
13 - $ref: "/schemas/input/matrix-keymap.yaml#"
22 refresh-rate-hz:
29 debounce-delay-ms:
35 linux,no-autorepeat:
38 default-brightness-level:
45 - compatible
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/extcon/
Dextcon-palmas.txt5 - compatible: should contain one of:
6 * "ti,palmas-usb-vid".
7 * "ti,twl6035-usb-vid".
8 * "ti,palmas-usb" (DEPRECATED - use "ti,palmas-usb-vid").
9 * "ti,twl6035-usb" (DEPRECATED - use "ti,twl6035-usb-vid").
12 - ti,wakeup : To enable the wakeup comparator in probe
13 - ti,enable-id-detection: Perform ID detection. If id-gpio is specified
14 it performs id-detection using GPIO else using OTG core.
15 - ti,enable-vbus-detection: Perform VBUS detection.
16 - id-gpio: gpio for GPIO ID detection. See gpio binding.
[all …]
Dwlf,arizona.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - patches@opensource.cirrus.com
20 wlf,hpdet-channel:
30 wlf,use-jd2:
35 wlf,use-jd2-nopull:
40 wlf,jd-invert:
45 wlf,micd-software-compare:
50 wlf,micd-detect-debounce:
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/sound/
Drt5682.txt7 - compatible : "realtek,rt5682" or "realtek,rt5682i"
9 - reg : The I2C address of the device.
13 - interrupts : The CODEC's interrupt output.
15 - realtek,dmic1-data-pin
20 - realtek,dmic1-clk-pin
24 - realtek,jd-src
28 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
30 - realtek,btndet-delay
31 The debounce delay for push button.
32 The delay time is realtek,btndet-delay value multiple of 8.192 ms.
[all …]
Dwm8903.txt7 - compatible : "wlf,wm8903"
9 - reg : the I2C address of the device.
11 - gpio-controller : Indicates this device is a GPIO controller.
13 - #gpio-cells : Should be two. The first cell is the pin number and the
18 - interrupts : The interrupt line the codec is connected to.
20 - micdet-cfg : Default register value for R6 (Mic Bias). If absent, the
23 - micdet-delay : The debounce delay for microphone detection in mS. If
26 - gpio-cfg : A list of GPIO configuration register values. The list must
31 - AVDD-supply : Analog power supply regulator on the AVDD pin.
33 - CPVDD-supply : Charge pump supply regulator on the CPVDD pin.
[all …]
/Linux-v5.15/drivers/input/keyboard/
Dlpc32xx-keys.c1 // SPDX-License-Identifier: GPL-2.0-or-later
63 u32 deb_clks; /* Debounce clocks (based on 32KHz clock) */
64 u32 scan_delay; /* Scan delay (based on 32KHz clock) */
74 struct input_dev *input = kscandat->input; in lpc32xx_mod_states()
78 key = readl(LPC32XX_KS_DATA(kscandat->kscan_base, col)); in lpc32xx_mod_states()
79 changed = key ^ kscandat->lastkeystates[col]; in lpc32xx_mod_states()
80 kscandat->lastkeystates[col] = key; in lpc32xx_mod_states()
86 kscandat->row_shift); in lpc32xx_mod_states()
87 keycode = kscandat->keymap[scancode]; in lpc32xx_mod_states()
99 for (i = 0; i < kscandat->matrix_sz; i++) in lpc32xx_kscan_irq()
[all …]
Dtc3589x-keypad.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) ST-Ericsson SA 2010
73 * struct tc35893_keypad_platform_data - platform specific keypad data
77 * @debounce_period: platform specific debounce time
95 * struct tc_keypad - data structure used by keypad driver
117 struct tc3589x *tc3589x = keypad->tc3589x; in tc3589x_keypad_init_key_hardware()
118 const struct tc3589x_keypad_platform_data *board = keypad->board; in tc3589x_keypad_init_key_hardware()
121 if (board->kcol > TC3589x_MAX_KPCOL || board->krow > TC3589x_MAX_KPROW) in tc3589x_keypad_init_key_hardware()
122 return -EINVAL; in tc3589x_keypad_init_key_hardware()
126 (board->krow << KP_ROW_SHIFT) | board->kcol); in tc3589x_keypad_init_key_hardware()
[all …]
Dtegra-kbc.c1 // SPDX-License-Identifier: GPL-2.0-or-later
6 * Copyright (c) 2009-2011, NVIDIA Corporation.
13 #include <linux/delay.h>
33 /* KBC row scan time and delay for beginning the row scan. */
156 val = readl(kbc->mmio + KBC_KP_ENT0_0 + i); in tegra_kbc_report_keys()
165 keycodes[num_down] = kbc->keycode[scancode]; in tegra_kbc_report_keys()
167 if ((keycodes[num_down] == KEY_FN) && kbc->use_fn_map) in tegra_kbc_report_keys()
178 * Ghosting occurs if there are 3 keys such that - in tegra_kbc_report_keys()
182 if (kbc->use_ghost_filter && num_down >= 3) { in tegra_kbc_report_keys()
190 * and the other is in the same column as the i-th key. in tegra_kbc_report_keys()
[all …]
/Linux-v5.15/drivers/extcon/
Dextcon-palmas.c1 // SPDX-License-Identifier: GPL-2.0-or-later
5 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com
12 #include <linux/devm-helpers.h>
25 #define USB_GPIO_DEBOUNCE_MS 20 /* ms */
45 struct extcon_dev *edev = palmas_usb->edev; in palmas_vbus_irq_handler()
48 palmas_read(palmas_usb->palmas, PALMAS_INTERRUPT_BASE, in palmas_vbus_irq_handler()
52 if (palmas_usb->linkstat != PALMAS_USB_STATE_VBUS) { in palmas_vbus_irq_handler()
53 palmas_usb->linkstat = PALMAS_USB_STATE_VBUS; in palmas_vbus_irq_handler()
55 dev_dbg(palmas_usb->dev, "USB cable is attached\n"); in palmas_vbus_irq_handler()
57 dev_dbg(palmas_usb->dev, in palmas_vbus_irq_handler()
[all …]
Dextcon-max8997.c1 // SPDX-License-Identifier: GPL-2.0+
3 // extcon-max8997.c - MAX8997 extcon driver to support MAX8997 MUIC
8 #include <linux/devm-helpers.h>
18 #include <linux/mfd/max8997-private.h>
19 #include <linux/extcon-provider.h>
22 #define DEV_NAME "max8997-muic"
26 ADC_DEBOUNCE_TIME_0_5MS = 0, /* 0.5ms */
27 ADC_DEBOUNCE_TIME_10MS, /* 10ms */
28 ADC_DEBOUNCE_TIME_25MS, /* 25ms */
29 ADC_DEBOUNCE_TIME_38_62MS, /* 38.62ms */
[all …]
/Linux-v5.15/arch/arm64/boot/dts/qcom/
Dsdm630-sony-xperia-nile.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/input/gpio-keys.h>
16 qcom,msm-id = <318 0>;
17 qcom,board-id = <8 1>;
18 qcom,pmic-id = <0x1001b 0x101011a 0x00 0x00 0x1001b 0x201011a 0x00 0x00>;
20 /* This part enables graphical output via bootloader-enabled display */
24 #address-cells = <2>;
25 #size-cells = <2>;
[all …]
Dmsm8994-sony-xperia-kitakami.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/gpio-keys.h>
18 * and requires driver-side changes (including CPR, be warned!!).
21 qcom,msm-id = <207 0x20000>, <207 0x20001>;
23 qcom,pmic-id = <0x10009 0x1000a 0x00 0x00>;
25 qcom,board-id = <8 0>;
28 /delete-node/ psci;
31 compatible = "gpio-keys";
32 input-name = "gpio-keys";
[all …]
Dmsm8998-oneplus-common.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
3 * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
20 qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */
23 #address-cells = <2>;
24 #size-cells = <2>;
29 compatible = "simple-framebuffer";
38 reserved-memory {
[all …]
Dsdm845-oneplus-common.dtsi1 // SPDX-License-Identifier: GPL-2.0
8 /dts-v1/;
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/linux-event-codes.h>
12 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
18 /delete-node/ &rmtfs_mem;
27 stdout-path = "serial0:115200n8";
30 gpio-keys {
31 compatible = "gpio-keys";
35 pinctrl-names = "default";
[all …]
/Linux-v5.15/Documentation/devicetree/bindings/mmc/
Dmmc-controller.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/mmc/mmc-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Ulf Hansson <ulf.hansson@linaro.org>
25 "#address-cells":
30 "#size-cells":
37 broken-cd:
42 cd-gpios:
47 non-removable:
[all …]
/Linux-v5.15/arch/arm/boot/dts/
Domap4-duovero-parlor.dts1 // SPDX-License-Identifier: GPL-2.0-only
5 /dts-v1/;
7 #include "omap4-duovero.dtsi"
9 #include <dt-bindings/input/input.h>
13 compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
20 compatible = "gpio-leds";
24 linux,default-trigger = "heartbeat";
29 compatible = "gpio-keys";
30 #address-cells = <1>;
31 #size-cells = <0>;
[all …]
Dlpc3250-phy3250.dts1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * PHYTEC phyCORE-LPC3250 board
5 * Copyright (C) 2015-2019 Vladimir Zapolskiy <vz@mleia.com>
9 /dts-v1/;
13 model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
22 compatible = "gpio-leds";
26 default-state = "off";
31 linux,default-trigger = "heartbeat";
37 power-supply = <&reg_lcd>;
41 remote-endpoint = <&cldc_output>;
[all …]
Dste-href-tvk1281618-r3.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later
7 #include <dt-bindings/interrupt-controller/irq.h>
8 #include <dt-bindings/input/input.h>
12 compatible = "gpio-keys";
13 #address-cells = <1>;
14 #size-cells = <0>;
15 vdd-supply = <&ab8500_ldo_aux1_reg>;
16 pinctrl-names = "default";
17 pinctrl-0 = <&hall_tvk_mode>;
32 interrupt-parent = <&gpio2>;
[all …]
/Linux-v5.15/arch/powerpc/boot/dts/
Dac14xx.dts1 // SPDX-License-Identifier: GPL-2.0-or-later
14 #address-cells = <1>;
15 #size-cells = <1>;
26 timebase-frequency = <40000000>; /* 40 MHz (csb/4) */
27 bus-frequency = <160000000>; /* 160 MHz csb bus */
28 clock-frequency = <400000000>; /* 400 MHz ppc core */
49 compatible = "cfi-flash";
51 #address-cells = <1>;
52 #size-cells = <1>;
53 bank-width = <2>;
[all …]
/Linux-v5.15/sound/soc/codecs/
Dmt6359-accdet.c1 // SPDX-License-Identifier: GPL-2.0
3 // mt6359-accdet.c -- ALSA SoC mt6359 accdet driver
20 #include <linux/delay.h>
31 #include "mt6359-accdet.h"
35 #define REGISTER_VAL(x) ((x) - 1)
63 unsigned int debounce);
77 if (priv->data->eint_detect_mode == 0x3 || in adjust_eint_analog_setting()
78 priv->data->eint_detect_mode == 0x4) { in adjust_eint_analog_setting()
80 regmap_update_bits(priv->regmap, in adjust_eint_analog_setting()
83 if (priv->data->eint_detect_mode == 0x4) { in adjust_eint_analog_setting()
[all …]
/Linux-v5.15/drivers/usb/dwc2/
Dcore.c1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
3 * core.c - DesignWare HS OTG Controller common routines
5 * Copyright (C) 2004-2013 Synopsys, Inc.
16 * 3. The names of the above-listed copyright holders may not be used
48 #include <linux/dma-mapping.h>
49 #include <linux/delay.h>
61 * dwc2_backup_global_registers() - Backup global controller registers.
71 dev_dbg(hsotg->dev, "%s\n", __func__); in dwc2_backup_global_registers()
74 gr = &hsotg->gr_backup; in dwc2_backup_global_registers()
76 gr->gotgctl = dwc2_readl(hsotg, GOTGCTL); in dwc2_backup_global_registers()
[all …]

1234